Pelco SRXP4-2V10-IMD, SRXP4-2V10-IMD-IR, SRXP4-2V10-EMD, SRXP4-2V10-EMD-IR, SRXP4-3V10-IMD operations manual

Sarix® Professional 4

Operations Manual

Document number:C6724M

Publication date:10/22

Sarix® Professional 4 Operations Manual

Table of Contents

Introduction 4

System Requirements 4

Accessing Camera Settings 5

Accessing the Camera Web Interface 5

Creating the Initial User 5

Logging In 5

Logging Out 6

Using the Live View 7

Saving a Still Image 7

Configuring the System Settings 8

Configuring General Settings 8

Managing the Camera Firmware 8

Configuring Storage Management 9

Enabling Onboard Storage 9
Downloading Recorded Video from the Web Interface 10
Downloading Recorded Video from the SD Card 10
Deleting Recorded Video 11

Configuring Diagnostics 11

Configuring the Network and Security Settings 12

Configuring the Network Settings 12

Configuring the Users 14

Adding a User 14
Modifying Users and Passwords 14
Removing a User 14
Keeping Usernames and Passwords After Firmware Revert 15

Configuring 802.1x Port-Based Authentication 15

Configuring the 802.1X Port Security 15
Switching 802.1X Authentication Profiles 16
Removing an 802.1X Authentication Profile 16
Returning to the Network Page 16

Configuring SNMP 16

Configuring the IP Filter 17

Configuring Imaging 19

Configuring General Imaging Settings 19

Understanding Backlight Compensation (BLC) and Wide Dynamic Range (WDR) 21

Adjusting White Balance Settings 21

Using Window Blanking 23

Setting a Window Blank 23
Deleting a Window Blank 24

C6724M | 10/22

2

Sarix® Professional 4 Operations Manual

Configuring A/V Streams 25

Compression and Image Rate 25

Enabling and Configuring Smart Compression 25

Saving or Restoring VideoConfigurations 26

Viewing the RTSP Stream URI 26

Accessing the Still Image URI 27

Setting Audio Configurations 27

Configuring Smart Compression Advanced Settings 27

Configuring Events 29

Configuring Motion Detection 29

Configuring Sabotage Detection 29

Configuring Digital Inputs and Outputs 30

C6724M | 10/22

3

Sarix® Professional 4 Operations Manual

Introduction

Before you access the web interface, make sure all the procedures described in the camera installation
guide have been completed.

Note: Features and options are disabled if they are not supported by the camera.

System Requirements

The web interface can be accessed from any Windows, Mac, or mobile device using one of the following
browsers:

l

Microsoft Edge

l

Mozilla Firefox

l

Google Chrome™

l

Android™

l

Apple iOS

Note: The web interface may work with older or unsupported browsers, but this has not been
tested.

C6724M | 10/22

4

Sarix® Professional 4 Operations Manual

Accessing Camera Settings

Use the Motorola Camera Configuration Tool (CCT) https://www.pelco.com/camera-configuration-tool/
or the camera web user interface to access camera settings.

Note:Smart Analytics configuration requires the CCT.

Accessing the Camera Web Interface

After the camera has been installed, use the camera's IP address to access the web interface. The IP
address can be found in the Motorola Camera Configuration (MCC) Tool — Click the Network tab to see
the details of the selected cameras.

After you identify the IP address, complete the following procedure to access the web interface:

Note:The web browser must be configured to accept cookies or the camera web interface will not
function correctly.

1. On a computer with access to the same network as the camera, enter the camera's IP address
into a web browser in the format http://<camera IP address>/

For example: http://192.168.1.40/

2. You will automatically be prompted to enter your username and password to access the camera.
You will be asked to create a user with administrator privileges before the device will be
operational. For more information, see Adding a User.

Creating the Initial User

Cameras do not have a default username and password and will be in a factory default state.

Caution

If the camera is in the factory default state, you will be redirected to the New User page to create an
administrator user:

1. Enter a new User Name or keep the default administrator name.

2. Enter a new Password for the user. It is recommended to use a secure and complex password.

3. Confirm the new password.

4. For the first user, Administrator must be selected in the Security Group drop-down menu.

5. Click Apply. After creating the user, you will be asked to login.

: You must create a user with

administrator

privileges before the camera is operational.

Logging In

You will automatically be prompted to enter your username and password to access the camera.

l

If the camera is in the factory default state, you will be asked to create a user with administrator
privileges before the camera will be operational. Use these credentials when logging in.

Note:Pelco recommends that you add a password after your first login. For more information, see

Modifying Users and Passwords.

C6724M | 10/22

5

Sarix® Professional 4 Operations Manual

Logging Out

To log out of the camera, at the upper right corner of the window, click Logout.

Note:After 15 minutes of inactivity, the Web UIwill automatically log the user out.

C6724M | 10/22

6

Sarix® Professional 4 Operations Manual

Using the Live View

After you log in, the first page you see is the Live View. The Live View contains an image panel that
displays the live video stream.

Use the tabs at the top of the window to navigate through the web interface. Click the Live View tab at
any time to return to this page.

Note: Features and options are disabled if they are not supported by the camera.

Saving a Still Image

If you see the Save Still to SDCard button on the Live View page, the camera supports the ability to
take snapshots of live video from the web interface.

To use this feature, the following settings are required for the camera:

l

There is an SD card inserted in the camera. For more information, see the camera's installation
guide.

l

The camera's onboard storage settings are enabled on the Storage Management page. For more
information, see Configuring Storage Management.

l

The camera's video format must be set to MJPEG in the VideoConfigurations page. For more
information, see Compression and Image Rate.

After all the requirements have been met, you can click Save Still to SDCard and the image that is
displayed in the Live View page is automatically saved to the SD card.

To download the snapshot, see Compression and Image Rate.

C6724M | 10/22

7

Sarix® Professional 4 Operations Manual

Configuring the System Settings

Use the System tab to configuring General Settings, Firmware, Storage Management, and Diagnostics.

Configuring General Settings

The General Settings page allows you to set the camera's identity.

Note: Features and options are disabled if they are not supported by the camera.

1. Click the System tab, and then click the General Settings tab.

2. In the Name field, give the camera a meaningful name.

3. In the Location field, describe the camera's location.

4. Select the Disable device status LEDs check box to disable the camera LED indicators.

5. Select any of the Overlay Settings check boxes to display and stamp that information on the
camera's video stream. The options are:

l

Display Date—Selecting the Display Date check box also enables the Date Format drop-
down menu. From the list, choose the date format.

l

Display Time

l

Display GMT Offset

l

Display Name

l

Display Location

6. In the Time Settings area, select how the camera keeps time.

l

To manually set the camera’s date and time, enter the time zone on this page.

l

Select the Automatically adjust clock for Daylight Savings Time check box, if required.

l

To auto-synchronize the camera’s date and time with an NTP server, configure the NTP
server on the Network and Security tab, Network page. See the section titled Configuring the

Network Settings.

Caution: The time setting must always be current. To ensure that the time is always current
you should do one of the following:

- Set up NTP on the DHCPserver, if your VMSsupports this feature.

- Use a valid public NTP server.

- Manually set the correct time in the Time Settings fields.

7. Click Apply to save the settings.

Managing the Camera Firmware

The Firmware page provides the current firmware version. From this page, you can also manually
upgrade the firmware, reboot the device, and restore to the factory defaults.

l

To manually upgrade the camera firmware:

1. Download the latest version of the firmware .bin file from the Pelco website
(www.pelco.com/training-support/).

C6724M | 10/22

8

Sarix® Professional 4 Operations Manual

2. Click the System tab, and then click the Firmware button.

3. Click Choose File, and then browse to and locate the downloaded firmware file.

4. Click Upgrade. Wait until the camera upgrade is complete.

l

To download a bug report, in the Download Bug Report area, click Download.

l

To reboot the camera, in the Reboot Device area, click Reboot.

l

To restore the camera to factory defaults, in the Restore to Factory Defaults area, click Restore.

Configuring Storage Management

On the Storage Management page, you can enable the camera’s onboard storage feature and download
recorded video directly from the camera. Onboard storage is available only on cameras equipped with an
SDcard or microSD card slot.

Note: For cameras with 2 microSD card slots, you will only be able to configure the microSD card
that is inserted first, in either card slot. The second microSD card slot is reserved for future use.

To access the Storage Management page, click the System tab, and then click the Storage
Management button.

Current information about the camera is presented in theDevice Information section at the top of the
page. It includes Status, Capacity, Current Usage, Remaining Capacity, and Measured Write Speed.

You can perform two actions in the Device Information area:

l

To format the SDcard, click Format Card.

l

Click to select or deselect the checkbox for Enable video alert overlay on severe SDcard failure.
When enabled, this feature shows an overlay on the video stream when the card cannot record
video, indicating that you must replace the card.

Enabling Onboard Storage

To use the camera’s onboard storage feature, you must first insert an SD card into the camera. Refer to
the camera’s installation manual for the location of the SD card slot.

The SD card will record from the camera's highest resolution stream. In most cases, this will be the
primary stream.

1. Click the System tab, and then click the Storage Management button.

2. In the Settings and Actions area, click to select the Enable Onboard Storage check box.

3. By default, the camera is set to only record to the SD card when it is unable to communicate with
the network video management server. If you prefer to have the camera record video to both the
network video management server and to the SD card, click to deselect the checkbox for the
Record only when server connection is interrupted to disable the setting.

4. Select one of the following recording modes:

l

Continuous: the camera never stops recording to the SD card.

l

On Motion: the camera only records when there is motion in the scene.
If you are configuring a Pelco video analytics camera, the On Motion setting will record either
pixel change in the scene or analytics motion events depending on how the camera is
configured.

The recorded video will be divided into files no more than five minutes in length or 100MB in size.

C6724M | 10/22

9

Sarix® Professional 4 Operations Manual

5. On the VideoConfigurations page, make sure the format is set to H.264 or H.265 to maximize the
SD card recording capacity and performance. See the section titled Compression and Image

Rate.

Downloading Recorded Video from the Web Interface

Listed in the Export Recordings section are all the videos that have been recorded to the SD card.

If you are using a CryptR micro card in the camera SD slot for FIPS level 3 encryption, you will not be
able to use onboard storage in the SD card slot. For cameras with 2 microSD slots you can only use the
slots for either storage or the CryptR micro card, both options cannot be used at the same time.

It is recommended that you download recorded video from the web interface. However, if your bandwidth
is limited, you can choose to download the recorded video directly from the SD card. For more
information, see Downloading Recorded Video from the SD Card.

To download recorded video from the web interface, perform the following:

1. Click the System tab, and then click the Storage Management button.

2. In the Export Recordings area, click to select the checkbox beside all the videos you want to
download.
To help you find the video you want, filter the videos by date and time. Click to select the checkbox
for Filter, type in the dates in the From and To fields, and then select the From and To time range.

3. Click Download.

The selected video files are automatically downloaded to your browser’s default Downloads folder. If you
are prompted by the browser, allow the download to occur.

Note: Do not close your browser window until the download is complete or the file might not
download correctly. This is important if you are downloading multiple video files because the files
are downloaded one by one.

Downloading Recorded Video from the SD Card

If you do not have enough bandwidth to download recorded video directly from the web interface, you
can choose to download the recorded video directly from the SD card.

To download recorded video directly from the SD card:

1. Click the System tab, and then click the Storage Management button.

2. In the Settings area, click to deselect the Enable Onboard Storage check box, and then click
Apply.

3. Remove the SD card from the camera.

4. Insert the SD card into a card reader.

5. When the Windows AutoPlay dialog box appears, select Open folder to view files.

6. Todownload all the recorded videos, click Download All; to download specific video, select the
video files you want then click Download Selected.

7. When you are prompted, choose a location to save the video files.
The files start downloading from the SD card and are saved to the selected location.

8. When you are ready, eject the SD card.

9. Insert the SD card back into the camera then click to select the checkbox for Enable Onboard
Storage to begin recording to the SD card again.

C6724M | 10/22

10