Pelco SM-IDM4018-3908, SM-IDM4018-3993 Specsheet

PRODUCT SPECIFICATION

IWM24-GY

camera solutions

IWM Series, IWM24 Series, and IDM4018 Mount

WALL MOUNT, SPECTRA®, DF5, DF8, AND SARIX™ IE SERIES DOMES

Product Features

• For Use with Spectra®, DF5, DF8, and Sarix™ IE Series Domes;

Can Also Be Used with Other Pendant Domes Using 1.5-inch NPT Threaded Pipe for Mounting

• Constructed of Aluminum (IDM4018) and Cast Aluminum

(IWM Series)

• Mounts Directly to Vertical Load-Bearing Surface for Wall Mount

Applications

• Supports up to 75 lb (34 kg)

• Includes Cable Feedthrough Hole

• IWM24 Series Includes Integral 24 VAC, 100 VA Transformer for Use

with Spectra and Sarix IE Series Domes

• Optional Parapet, Pole, and Corner Adapters are Available

The

IWM Series, IWM24 Series,

and

IDM4018

indoor/outdoor wall mounts are designed primarily for use with Pelco pendant domes including Spectra®, DF5, DF8, and Sarix™ IE Series. They can also be used with other pendant domes that require 1.5-inch NPT pipe thread for installation. For Sarix IE Series domes, the IWM-SR and IWM24-SR wall mounts require the Sarix IE-P pendant mount adapter.

All mounts feature a feedthrough opening in the mounting surface for easy routing of video and power cables and are threaded for

1.5-inch NPT pipe, making them ready to accept a variety of Pelco pendant back box models.

14.629 (37.15)

13.50 (34.30)

8.0

(20.32)

7.5

(19.05)

4.5 (11.43)

5.50 (13.97)

6.5

(16.51)

The

IWM24 Series

includes an integral 24 VAC, 100 VA transformer. Input power (120 or 240 VAC, 50/60 Hz) is selectable using an internal slide switch that is easily accessible through a front access cover plate. Input wiring can enter the arm from openings in the mounting plate or a ﬂexible metal conduit ﬁtting may be installed on the bottom of the mount. When installed with Sarix IE Series domes, the power from the IWM24-SR mount is used for the dome heater.

The

IWM Series, IWM24 Series

, and

IDM4018

mounts can be attached directly to any vertical load-bearing surface. All mounts are designed to support up to 75 pounds (34 kg).

The

IWM Series

and

IWM24 Series

are constructed of cast

aluminum and are available in black, gray, or light gray ﬁnish. The

IDM4018

is constructed of aluminum and has a gray polyester powder coat ﬁnish. Optional parapet, pole, and corner adapters are available.

NOTE: VALUES IN PARENTHESES ARE CENTIMETERS;

ALL OTHERS ARE INCHES.

International Standards

Organization Registered Firm;

ISO 9001 Quality System

C203 / REVISED 10-6-10

TECHNICAL SPECIFICATIONS

MODELS

IWM-BK Wall mount with cable feedthrough for use

with Spectra, DF5, and DF8 Series pendant

domes; black ﬁnish. IWM-GY Same as IWM-BK except gray ﬁnish. IWM-SR Same as IWM-BK except light gray ﬁnish.* IWM24-BK Wall mount with cable feedthrough for use

with Spectra, DF5, and DF8 Series pendant

domes; includes integral 24 VAC, 100 VA

transformer; black ﬁnish. IWM24-GY Same as IWM24-BK except gray ﬁnish. IWM24-SR Same as IWM24-BK except light gray ﬁnish.* IDM4018 Wall mount with removable front end cap and

feedthrough capabilities for use with Spectra,

DF5, and DF8 Series pendant domes.

ELECTRICAL

(IWM24 Series Only)

Input Power 120/240 VAC, 50/60 Hz, switchable through

an internal slide switch Output Power 24 VAC, 100 VA transformer Fuse One 1.6 A, 120 VAC, fast acting

One 500 mA, 240 VAC, fast acting

GENERAL

Suggested Mounting Method

IWM/IWM24 Series Secure with four 3/8-inch fasteners (not

supplied) suitable for the mounting surface

IDM4018 Secure with four 5/16-inch fasteners (not

supplied) suitable for the mounting surface Dome Mounting Dome screws directly into mount Cable Entry

IWM Series and IDM4018 One cable feedthrough hole in mounting plate IWM24 Series Two cable feedthrough holes in mounting

plate; can accommodate 1/2-inch (1.27 cm)

conduit ﬁttings or PG13.5 liquid-tight gland

ﬁttings; one 3/4-inch (1.91 cm) conduit

opening on the bottom of mount arm for

ﬂexible metal conduit connectors Maximum Load 75 lb (34 kg) Effective Projected Area (EPA)

IWM/IWM24 Series ~48 square inches IDM4018 ~54 square inches

Construction

IWM/IWM24 Series Cast aluminum IDM4018 5052H32 Aluminum

Finish

IWM-BK Black polyester powder coat IWM-GY Gray polyester powder coat IWM-SR Light gray polyester powder coat IWM24-BK Black polyester powder coat IWM24-GY Gray polyester powder coat IWM24-SR Light gray polyester powder coat

IDM4018 Gray polyester powder coat Environment Indoor/outdoor Weight Unit Shipping

IWM Series 2.46 lb (1.12 kg) 7 lb (3.17 kg)

IWM24 Series 6.58 lb (2.98 kg) 11 lb (4.98 kg)

IDM4018 4.00 lb (1.81 kg) 6 lb (2.71 kg)

CERTIFICATIONS/RATINGS

• CE compliant (IWM24-BK, IWM24-GY, and IWM24-SR only)

• UL/cUL Listed (IWM/IWM24 Series only)

• Meets NEMA Type 4 Standards (IWM/IWM24 Series only)

OPTIONAL MOUNT ADAPTERS

Corner

CM400 Corner mount adapter; use with IDM4018 and

Pole

PA402 Pole mount adapter; use with IDM4018 and

Parapet

PP400 Parapet wall adapter; use with IDM4018 and

PP4348 Rooftop parapet adapter; use with IDM4018

4.50

0.75

(1.90)

6.50

(16.51)

0.75

(1.90)

(11.43)

6.00

(15.24)

NOTE: VALUES IN PARENTHESES ARE CENTIMETERS; ALL OTHERS ARE INCHES.

*The IWM-SR and IWM24-SR require the IE-P adapter for use with

Sarix IE Series domes.

IWM/IWM24 Series

and IWM/IWM24 Series

IDM4018

8.00

2.50

(20.32)

(6.35)

0.31 (0.95) THRU (4X)

18.00 (45.72)

1.75

(4.45)

Pelco, Inc. Worldwide Headquarters:

3500 Pelco Way, Clovis, California 93612-5699 USA

USA & Canada International www.pelco.com

Tel: (800) 289-9100 • FAX: (800) 289-9150

Tel: +1 (559) 292-1981 • FAX: +1 (559) 348-1120

Pelco, the Pelco logo, and other trademarks associated with Pelco products referred

to in this publication are trademarks of Pelco, Inc. or its afﬁliates. All other

product names and services are the property of their respective companies.

Product speciﬁcations and availability are subject to change without notice.