Spectra® IV SL and Spectra IV SE are Pelco’s premier integrated dome systems. These systems feature a high resolution camera/optics package
with configurable dome drive software.
This manual is designed primarily to be a reference tool for the installation and operation of your system. Inside you will find information about
features and commands, as well as a detailed menu tree and a quick start guide.
Be sure to thoroughly familiarize yourself with the information in this manual before installing and using your system.
C3463M-C (7/11)7
Installation
SW1
SW2
ON
12345678910
ON
12345678
This manual contains installation instructions for the Spectra IV dome drive only. For complete installation instructions for a Spectra IV dome
system, refer to the installation manual that was shipped with the back box.
SWITCH SETTINGS
Before installing the dome drive, you must configure the receiver address, termination, and baud setting. The DIP switches used to configure
these settings are located on the base of the dome drive.
Figure 1 shows the default settings for the DIP switches. Switch SW1-1 (SW1, swit
ch 1) is set to the ON position; all other switches are set to
the OFF position.
Refer to the following sections to set the address, termination, and baud settings for the dome drive.
Figure 1. Default Switch Settings
SW1: RECEIVER ADDRESS
Set the SW1 switches for the address of the dome drive. The following information is required to set the dome drive address:
Pelco P-type control: The default address is 2. Refer to Tab le F on page 66 for address settings that use Pelco P-type control. The maximum
number of receivers is 32.
Pelco D-type control: The default address is 1. Refer to Ta bl e G on page 67 for address settings that use Pelco D-type control. The maximum
number of receivers is 254.
SW2 SWITCH 1: AD-32 PRESET SYSTEM
SW2-1 should be set to the ON position if an AD-32 controller and Pelco’s TXB-AD translator board are used to control the dome system.
SW2 SWITCH 2: CM9502 SETTING
If a CM9502 matrix system is used with the dome drive, set SW2-2 to the ON position.
SW2 SWITCH 3: CONTROL SYSTEM COMPATIBILITY
Coaxial Control Systems
Although Spectra IV dome systems can operate with coaxial control systems from many manufacturers, the system is designed for optimal
performance with Pelco Coaxitron
To compensate for coaxial control systems from other manufacturers, Pelco has provided DIP switch SW2-3. Setting SW2-3 to the ON po
may improve dome control with these control systems.
If you are using a Pelco Coaxitron controller, leave SW2-3 in the default OFF position.
NOTES:
•This coaxial control system compatibility featu
IV Horizon dome drives). The revision number can be found on the barcode label on the top of the dome drive. Software version 1.090 and
later indicates this mode is available by placing an asterisk next to the switch number in the Dip Switch Information menu.
•In some configurations, Pelco CM9502 Series matrix systems use no
you experience problems with these functions, set SW2-3 to the ON position.
8C3463M-C (7/11)
®
control products within the length specified for coaxial cable.
re is only available for dome drive revisions A4 and later (revisions A0 and later for Spectra
nstandard Coaxitron commands for functions like pattern playback. If
sition
Pelco P Protocol Control Systems
To compensate for Pelco P protocol control systems from other manufacturers, set SW2-3 to the ON position. This may improve dome control
with some of these control systems.
SW2 SWITCHES 4 AND 5: SERIAL PORT SETTINGS
RS-422 Setting (Default)
SW2-4 and SW2-5 should both be set to the OFF position for RS-422 setting.
For control, only two wires should be connected to the RX- and RX+ connectors on the circuit board inside the back box. For bidirectional control,
four wires should be connected to the RX-, RX+, TX-, and TX+ connectors on the circuit board inside the back box.
RS-485, 4-Wire Setting
SW2-4 should be set to OFF and SW2-5 should be set to ON if a 4-wire serial port connection is used with RS-485.
NOTE: This setting is most commonly used with Pelco Endura® systems.
RS-485, 2-Wire Setting
SW2-4 and SW2-5 should both be set to the ON position if a 2-wire serial port connection is used with RS-485.
This setting is used to allow the Spectra dome system to transmit and receive commands on the same pair of wires. Only two wires should be
connected to the RX- and RX+ connectors on the circuit board inside the back box.
SW2 SWITCHES 6 TO 8: BAUD SETTINGS
Pelco D-type controllers are set for 2400 baud. The default setting for the dome drive is 2400 baud. If you are using a Pelco D-type controller, do
not reset SW2 switches 1 to 3 or SW2 switches 6 to 8.
Pelco P-type controllers can operate at 2400, 4800, and 9600 baud. Set the SW2 switches (6, 7, and 8), located on the base of the dome drive, to
the same baud as the Pelco P-type controller.
Table A. Baud Settings
Switch NumberSW2-6SW2-7SW2-8
2400 Baud (default for Pelco D-type control)OffOffOff
4800 Baud (default for Pelco P-type control)OnOffOff
9600 BaudOffOnOff
SW2 Switch 9: Coaxial/UTP Cable
SW2-9 should be set to the OFF position (default) if you are using coaxial cable. If you are using unsheilded twisted pair (UTP) cable, set SW2-9
to the ON position.
SW2 Switch 10: Termination Setting
When connecting more than one Spectra IV dome system to a single controller, terminate the unit farthest from the controller. Termination is only
required for the last dome in the series.
The dome drive is shipped from the factory in the unterminated (OFF) position. To terminate the dome drive, set SW2-10 to the ON position.
NOTE: Dome termination is not required for Coaxitron control.
C3463M-C (7/11)9
DOME DRIVE
To install the dome drive:
1. Align the blue and red tabs with the blue and red arrows on the hinged door inside the back box.
2. Push the tabs in. Insert one side and then the other side.
3. Continue pushing on the ends of the tabs until both sides click into place (refer to Figure 2).
NOTE: When removing a dome drive that has been in use, caution should be taken to avoid direct contact with the top plate of the unit. This
section of the unit will be warm to the touch when first removed from an operating unit.
Figure 2. Dome Drive Installation
4. Apply power to the Spectra IV dome system. The system will start a configuration sequence. When configuration is done, the foll
information is displayed:
Pelco Spectra IV SL/Spectra IV SE
Version X.XX
D Address: 1
P Address: 2
Comm 2400, N, 8, 1
CONFIGURE DONE
This information will remain on the moni
NOTE: When installing a Spec
complete, the dome drive will continue with a normal configuration sequence.
tor until dome operation begins.
tra IV dome drive in a Spectra III™ back box for the first time, a message appears. When the installation is
owing
10C3463M-C (7/11)
Operation
*Digital zoom magnifies the image electronically and the picture may appear pixilated. The larger the digital zoom limit the greater the reduction in
resolution.
†
The dome cannot do electronic zoom in a pattern. Optical zoom will operate in a pattern.
QUICK OPERATION GUIDE
Pan and TiltMove the joystick or press the direction keys left/right and up/down.
Zoom FarT
Zoom WideP
Scanning
PresetsRef
Patterns
ZonesRe
AlarmsRe
Auto FlipT
†
o zoom far:
1. Press the Zoom Tele button or turn the joystick clockwise until zoom stops at the optical zoom limit.
2. Release the button or joystick for one second.
3. To continue zooming (digitally), press the button or turn the joystick clockwise again until you have the picture you want
o
r reach the digital zoom* limit.
ress the Zoom Wide button or turn the joystick counterclockwise.
Stop ScanPreset 96
Random ScanPreset 97
Frame ScanPreset 98
Auto ScanPreset 99
er to the documentation supplied with the control system.
Refer to the documentation supplied with the control system.
fer to Zones on page 42 and to the documentation supplied with the control system.
fer to Alarms on page 46.
urn on or off in the camera menu. Refer to Auto Flip on page 30.
QUICK CONFIGURATION GUIDE
1. Configure preset 95 to access the main menu (refer to Preset 95: Accessing Main Menu on page 12).
2. Use the joystick to position the cursor beside the menu selection.
NOTE: If your controller does not have a joystick, use the up or down key.
3. Press Iris Open, the submenu/cursor moves to the right.
4. Move the joystick up or down to
5. Press Iris Open to enter the selection.
6. Press Iris Close to cancel the selection.
view the selections.
C3463M-C (7/11)11
PRESET 95: ACCESSING MAIN MENU
You can call up the main menu on your monitor by configuring (setting or creating) preset 95 (preset 28 in AD-32 preset mode).
Configuring preset 95 for Pelco’s controllers varies according to the type of controller you are using. Instructions for configuring preset 95 are
given below for various Pelco controllers.
CM6700/CM6800
1. Enter the number of the Spectra IV dome system and press the CAM key.
2. Enter 95 and hold the PRESET key for two seconds.
3. In the Edit Preset menu, go to SET and press the ACK key. The main menu appears.
KBD200A/KBD300A: Direct Mode Only
1. Enter 95.
2. Hold the PRESET key (approximately five seconds) until the main menu appears on the screen.
CM9500
1. Enter the number of the Spectra IV dome system and press the CAM key. The main menu appears.
2. Highlight SETUP in the main menu and press the SELECT key.
3. Highlight CAM in the Setup menu and press the SELECT key.
4. Highlight PRESET in the Camera menu and press the SELECT key.
5. Enter 95 and press the F1 key. The main menu appears.
CM9740/CM9760/CM9770/CM9780
1. Press the ESCAPE key to open the main menu. Select DEF. The Define submenu appears.
2. Enter your four-digit PIN if this is your first time entering this mode.
3. Enter 95 and select PRST. The main menu appears.
4. Select the Quit icon to return to the default menu.
KBD4000/KBD4002
1. Press the SPOT MONITOR key.
2. Enter 95, then hold the PRESET key (approximately five seconds) until the main menu appears on the screen.
MPT9500
Extended Coaxitron or RS-485 Mode
1. Enter 95 and press the PRESET SET key.
2. Press the F2 key. The main menu appears.
NET300/NET350/NET4001A
1. Check the Set box.
2. Click the preset 95 button. The main menu appears.
12C3463M-C (7/11)
ENDURA WORKSTATION
1. Right-click in the video pane of the Spectra IV dome system.
2. Click Preset and then click Select Preset.
3. Enter 95 and then click OK.
VCD5000
1. Enter 95 for the preset action. The shortcuts menu appears.
2. Press the Preset button on the KBD5000.
DX4100/DX4500/DX4600/DX8100
1. Click the PTZ button on the toolbar. The PTZ control appears.
2. Click the Program button on the PTZ control. The main menu appears.
DIGITAL SENTRY® SYSTEM SOFTWARE
1. Click the PTZ tab.
2. Click the right or left arrows below the Go to Preset button until Go to Preset 95 appears on the button.
3. Click the Go to Preset 95 button. The main menu appears.
DIGITAL SENTRY DS CONTROLPOINT
1. Click the PTZ Controls icon. The PTZ Control tab appears below the PTZ video frame.
2. Click the up and down arrows to display 95 in the Preset Name text box.
3. Click the Call button. The main menu appears.
DVR5100
1. While in live view mode, select a video pane that is displaying video from a Spectra IV dome system.
2. From the Main menu, click Actions. The Actions menu appears.
3. From the Actions menu, click PTZ Operations. The PTZ Operations dialog box appears.
4. In the PTZ Operations dialog box, type 95 in the text box, and then click Presets. The main menu appears.
C3463M-C (7/11)13
23X LowLight Day/Night Menu Tree
CLEAR ALL ZONES
CLEAR ALL PRESETS
CLEAR ALL PATTERNS
CLEAR ALL WINDOW BLANKINGRESTORE FACTORY DEFAULTS
CLEAR
TEMPERATURE
DEWPOINT
PRESSURE
REFRESH
CURRENT READING
CONSTAN T
ALWAYS ON
NO
REPEAT
ACK ACTION
ACTIVATE AUX
<CURRENT READING>
RESET ALERT
STYLE
BLANK ALL ABOVE
BLANK ALL BELOW
<SET WINDOWS>
WINDOW BLANKING
1
ON
OFF
ZONE NUMBER
***ZONE NOT DEFINED***
<EDIT ZONE LABEL>
<EDIT ZONE>
ZONE ENABLED
ZONE BLANKING
<CLEAR ZONE>
ZONES
ON
ON
0
NONE
25
AUTO
ON
AUTO FLIP
PROPORTIONAL PAN
PARK TIME (MINUTES)
PARK ACTIONSCAN SPEED DEG/S
PRESET FREEZE FRAME
LIMIT STOPS
<SET MANUAL STOPS>
<CLEAR MANUAL STOPS>
<SET SCAN STOPS>
<CLEAR SCAN STOPS>
<SET AZIMUTH ZERO>
<CLEAR AZIMUTH ZERO>
MOTION
AUTO
28
AUTO
66
8
ON
26
ON
255
255
OFF
HIGH
SHUTTER SPEED
AGC LIMIT
AUTO IRIS
AUTO IRIS LEVEL
AUTO IRIS PEAK
AUTO SHARPNESSSHARPNESS LEVEL
AUTO WHITE BALANCE
R GAIN
B GAIN
BACKLIGHT COMP
VIDEO LEVEL
ADVANCED SETTINGS
T1
ON
XXXX
XXXX
TYPE OF LIGHTING
AUTO FOCUS
IR CUT FILTER
AUTO IR LEVEL
<ADVANCED SETTINGS>
PRESET LABEL
ZONE LABEL
ZOOM
AZIMUTH/ELEVATION
DIRECTION
ALARM MESSAGE
DATE/TIME
<LABEL POSITIONS>
RESTORE FACTORY DEFAULTS
DISPLAY SETUP
12345678 1234567890
SW1[--------] SW2[----------]
SW1 1-8:
D ADDRESS 1
P ADDRESS 2
SW2 1 : 32 PRESETS. OFF
SW2 2 : CM9500 MODE. OFF
SW2 3 : COAX SPIV COMM
SW2 4-5 : RS422 <->
SW2 6-8 : COMM. 2400.N.8.1
SW2 9 : UTC SOURCE. COAX
SW2 10 : TX/RX TERM.. OFF
PRESS IRIS OPEN TO CONTINUE
DIPSWITCH INFORMATION
XXXXXX
POWER ON
0°
YES
YES
NORMAL
XXXX-XXXX
ENGLISH X.XX
ITALIANO X.XX
FREE MEMORY
LAST RESET
AZIMUTH ZERO OFFSET
MOTOR ACTIVECAMERA ACTIVE
VIDEO LEVEL
CAMERA MODEL
LANGUAGE 1
. . .
LANGUAGE 10
<DIPSWITCH INFORMATION>
ADDITIONAL
XXXXXXXXXXXXXX
XX-XXXX
AVAILABLE
XX.X
XX.X
XXXXXXXXXX
1
2
OFF
OFF
C
X.XX
SERIAL #
DOME DRIVE MODEL
BACK BOX MEMORYSOFTWARE VERSION
BUILD
FONT VERSION
COMM
D ADDRESS
P ADDRESSCM95OO MODE
32 PRESETS
PROTOCOL
PRESSURIZED*
<ADDITIONAL>
*This setting applies to Pressurized Spectra IV dome systems only. Spectra IV systems that are not pressurized will not display this menu item.
NOTE: The BACK and EXIT options do not appear in these menus due to space limitations. See the individual menus in this document for complete
configurations.
14C3463M-C (7/11)
INTERNAL CLOCK
12 HOUR
12:00 AM
MM/DD/YYYY
00/00/0000
OFF
TIME BASE
TIME FORMAT
SET TIME
DATE FORMAT
SET DATE
DAYLIGHT SAVINGS
STYLE
BLANK ALL ABOVE
BLANK ALL BELOW
<SET WINDOWS>
WINDOW BLANKING
1
ON
OFF
ZONE NUMBER
***ZONE NOT DEFINED***
<EDIT ZONE LABEL>
<EDIT ZONE>
ZONE ENABLED
ZONE BLANKING
<CLEAR ZONE>
ZONES
1
0%
100%
PATTERN NUMBER
<PROGRAM PATTERN>
<CLEAR PATTERN>
<EDIT SCHEDULE>
REFERENCE INFO
PATTERN USAGE
REMAINING
PATTERNS
OFF
ON
HIGH
60
ON
STOP
OFF
AUTO TRACKING
DISPLAY SETUP
SENSITIVITY
START TIME
ZOOM
LOST ACTION
RETURN
AUTO TRACKING
ON
ON
0
NONE
25
AUTO
ON
AUTO FLIP
PROPORTIONAL PAN
PARK TIME (MINUTES)
PARK ACTIONSCAN SPEED DEG/S
PRESET FREEZE FRAME
LIMIT STOPS
<SET MANUAL STOPS>
<CLEAR MANUAL STOPS>
<SET SCAN STOPS>
<CLEAR SCAN STOPS>
<SET AZIMUTH ZERO>
<CLEAR AZIMUTH ZERO>
REFERENCE INFORMATION
MANUAL LIMITS SETSCAN LIMITSSET
MOTION
AUTO
28
AUTO
66
8
ON
26
ON
255
255
OFF
OFF
ON
HIGH
OFF
DEFAULT
30 CM
NIGHT
SHUTTER SPEED
AGC LIMIT
AUTO IRIS
AUTO IRIS LEVEL
AUTO IRIS PEAK
AUTO SHARPNESSSHARPNESS LEVEL
AUTO WHITE BALANCE
R GAIN
B GAIN
BACKLIGHT COMP
WIDE DYNAMIC RANGE
NEXT
BACK
EXIT
LOW LUX NOISE REDUCTION
VIDEO LEVEL
FIELD ALIGN
LOW LIGHT SHARPNESS
MINIMUM FOCUS DISTAN CE
ZOOM FOCUS TRACE
ADVANCED SETTINGS
T1
NORMAL
ON
OFF
OFF
XXXX
XXXX
XXXXXX
XXXX
DUSK
OFF
TYPE OF LIGHTING
PICTURE MODE
AUTO FOCUSSURE FOCUS
PT FOCUS LOCK
ZOOM LIMIT
ZOOM SPEED
LOW LIGHT LIMIT
IR CUT FILTER
AUTO IR LEVEL
LOW LIGHT FOCUS
PRESET LABEL
ZONE LABEL
ZOOM
AZIMUTH/ELEVATION
DIRECTION
ALARM MESSAGE
DATE/TIME
EVENT LABEL
<LABEL POSITIONS>
RESTORE FACTORY DEFAULTS
DISPLAY SETUP
12345678 1234567890
SW1[--------] SW2[----------]
SW1 1-8:
D ADDRESS 1
P ADDRESS 2
SW2 1 : 32 PRESETS. OFF
SW2 2 : CM9500 MODE. OFF
SW2 3 : COAX SPIV COMM
SW2 4-5 : RS422 <->
SW2 6-8 : COMM. 2400.N.8.1
SW2 9 : UTC SOURCE. COAX
SW2 10 : TX/RX TERM.. OFF
PRESS IRIS OPEN TO CONTINUE
DIPSWITCH INFORMATION
XXXXXX
POWER ON
0°
YES
YES
NORMAL
XXXX-XXXX
ENGLISH X.XX
ITALIANO X.XX
FREE MEMORY
LAST RESET
AZIMUTH ZERO OFFSET
MOTOR ACTIVE
CAMERA ACTIVE
VIDEO LEVEL
CAMERA MODEL
LANGUAGE 1
. . .
LANGUAGE 10
<DIPSWITCH INFORMATION>
ADDITIONAL
XXXXXXXXXXXXXX
XX-XXXX
AVAILABLE
XX.X
XX.X
XXXXXXXXXX
1
2
OFF
OFF
C
X.XX
SERIAL #
DOME DRIVE MODEL
BACK BOX MEMORY
SOFTWARE VERSION
BUILD
FONT VERSION
COMM
D ADDRESS
P ADDRESSCM95OO MODE
32 PRESETS
PROTOCOL
PRESSURIZED*
<ADDITIONAL>
*This setting applies to Pressurized Spectra IV dome systems only. Spectra IV systems that are not pressurized will not display this menu item.
NOTE: The BACK and EXIT options do not appear in these menus due to space limitations. See the individual menus in this document for complete
configurations.
16C3463M-C (7/11)
EVENT01
ON
12:00 AM
ON
ON
ON
ON
ON
ON
ON
SKIP HOLIDAYS
PRESET
1
EVENT LABEL
EVENT ACTIVE
EVENT TIME
EVENT OCCURSSUNDAY
MONDAY
TUESDAY
WEDNESDAY
THURSDAY
FRIDAY
SATURDAY
HOLIDAY
STYLE
BLANK ALL ABOVE
BLANK ALL BELOW
<SET WINDOWS>
WINDOW BLANKING
1
ON
OFF
ZONE NUMBER
***ZONE NOT DEFINED***
<EDIT ZONE LABEL>
<EDIT ZONE>
ZONE ENABLED
ZONE BLANKING
<CLEAR ZONE>
ZONES
1
0%
100%
PATTERN NUMBER
<PROGRAM PATTERN>
<CLEAR PATTERN>
<EDIT SCHEDULE>
REFERENCE INFO
PATTERN USAGE
REMAINING
PATTERNS
OFF
ON
HIGH
60
ON
STOP
OFF
AUTO TRACKING
DISPLAY SETUP
SENSITIVITY
START TIME
ZOOM
LOST ACTION
RETURN
AUTO TRACKING
ON
ON
0
NONE
25
AUTO
ON
AUTO FLIP
PROPORTIONAL PAN
PARK TIME (MINUTES)
PARK ACTIONSCAN SPEED DEG/S
PRESET FREEZE FRAME
LIMIT STOPS
<SET MANUAL STOPS>
<CLEAR MANUAL STOPS>
<SET SCAN STOPS>
<CLEAR SCAN STOPS>
<SET AZIMUTH ZERO>
<CLEAR AZIMUTH ZERO>
MOTION
AUTO
28
AUTO
66
8
ON
26
ON
255
255
OFF
OFF
OFF
ON
HIGH
OFF
DEFAULT
30 CM
NIGHT
SHUTTER SPEED
AGC LIMIT
AUTO IRIS
AUTO IRIS LEVEL
AUTO IRIS PEAK
AUTO SHARPNESSSHARPNESS LEVEL
AUTO WHITE BALANCE
R GAIN
B GAIN
BACKLIGHT COMP
E. IMAGE STABILIZER
WIDE DYNAMIC RANGE
NEXT
BACK
EXIT
LOW LUX NOISE REDUCTION
VIDEO LEVEL
FIELD ALIGN
LOW LIGHT SHARPNESS
MINIMUM FOCUS DISTAN CE
ZOOM FOCUS TRACE
ADVANCED SETTINGS
T1
NORMAL
ON
OFF
OFF
XXXX
XXXX
XXXXXX
XXXX
DUSK
OFF
TYPE OF LIGHTING
PICTURE MODE
AUTO FOCUSSURE FOCUS
PT FOCUS LOCK
ZOOM LIMIT
ZOOM SPEED
LOW LIGHT LIMIT
IR CUT FILTER
AUTO IR LEVEL
LOW LIGHT FOCUS
PRESET LABEL
ZONE LABEL
ZOOM
AZIMUTH/ELEVATION
DIRECTION
ALARM MESSAGE
DATE/TIME
EVENT LABEL
<LABEL POSITIONS>
RESTORE FACTORY DEFAULTS
DISPLAY SETUP
12345678 1234567890
SW1[--------] SW2[----------]
SW1 1-8:
D ADDRESS 1
P ADDRESS 2
SW2 1 : 32 PRESETS. OFF
SW2 2 : CM9500 MODE. OFF
SW2 3 : COAX SPIV
SW2 4-5 : RS422 <->
SW2 6-8 : COMM. 2400.N.8.1
SW2 9 : UTC SOURCE. COAX
SW2 10 : TX/RX TERM.. OFF
PRESS IRIS OPEN TO CONTINUE
DIPSWITCH INFORMATION
XXXXXX
POWER ON
0°
YES
YES
NORMAL
XXXX-XXXX
ENGLISH X.XX
ITALIANO X.XX
FREE MEMORY
LAST RESET
AZIMUTH ZERO OFFSET
MOTOR ACTIVE
CAMERA ACTIVE
VIDEO LEVEL
CAMERA MODEL
LANGUAGE 1
. . .
LANGUAGE 10
<DIPSWITCH INFORMATION>
ADDITIONAL
XXXXXXXXXXXXXX
XX-XXXX
AVAILABLE
XX.X
XX.X
XXXXXXXXXX
1
2
OFF
OFF
C
X.XX
SERIAL #
DOME DRIVE MODEL
BACK BOX MEMORY
SOFTWARE VERSION
BUILD
FONT VERSION
COMM
D ADDRESS
P ADDRESSCM95OO MODE
32 PRESETS
PROTOCOL
PRESSURIZED*
<ADDITIONAL>
*This setting applies to Pressurized Spectra IV dome systems only. Spectra IV systems that are not pressurized will not display this menu item.
NOTE: The BACK and EXIT options do not appear in the menus due to space limitations. See the individual menus in this document for complete
configurations.
18C3463M-C (7/11)
EVENT01
ON
12:00 AM
ON
ON
ON
ON
ON
ON
ON
SKIP HOLIDAYS
PRESET
1
EVENT LABEL
EVENT ACTIVE
EVENT TIME
EVENT OCCURSSUNDAY
MONDAY
TUESDAY
WEDNESDAY
THURSDAY
FRIDAY
SATURDAY
HOLIDAY
*This setting applies to Pressurized Spectra IV dome systems only.
The language for the on-screen menus is selectable. Available languages include English, Spanish, French, German, Italian, Portuguese, Russian,
Polish, Turkish, and Czech. The factory default language is English.
To change the display language:
1. Use the joystick to position the cursor beside LANGUAGE.
2. Press Iris Open. The cursor moves to the right, beside the current, selected language.
3. Move the joystick up or down to view the selections. Press Iris Open to enter the selection. All on-screen menus are changed to the
selected language.
SERIAL #
DOME DRIVE MODEL
BACK BOX MEMORY
SOFTWARE VERSION
BUILD
FONT VERSION
COMM
D ADDRESS
P ADDRESS
CM9500 MODE
32 PRESETS
PROTOCOL
PRESSURIZED*
<ADDITIONAL>
SYSTEM INFORMATION
BACK
EXIT
FREE MEMORY
LAST RESET
AZIMUTH ZERO OFFSET
MOTOR ACTIVE
CAMERA ACTIVE
VIDEO LEVEL
CAMERA MODEL
LANGUAGE 1
LANGUAGE 2
LANGUAGE 3
LANGUAGE 4
LANGUAGE 5
LANGUAGE 6
LANGUAGE 7
LANGUAGE 8
LANGUAGE 9
LANGUAGE 10
<DIPSWITCH INFORMATION>
ADDITIONAL
System Information
*This setting applies to Pressurized Spectra IV dome systems only.
DIP SWITCH INFORMATION
1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 9 0
SW1[- - - - - - - -] SW2[- - - - - - - - - -]
SW1 1-8 :
D ADDRESS 1
P ADDRESS 1
SW2 1 : 32 PRESETS. OFF
SW2 2 : CM9500 MODE. OFF
SW2 3 : COAX SPIV
SW2 4-5 : RS422 <->
SW2 6-8 : COMM. 2400.N.8.1
SW2 9 : UTC SOURCE. COAX
SW2 10 : TX/RX TERM.. OFF
PRESS IRIS OPEN TO CONTINUE
The System Information menu displays the dome drive model, software version, available memory, DIP switch information, and other diagnostic
information.
System settings cannot be changed using this menu; this information is for reference only.
Use the following steps to display the System Information menu:
1. Use the joystick to position the cursor beside SYSTEM
INFORMATION.
2. Press Iris Open. The SYSTEM INFORMA
DIP SWITCH INFORMATION
The DIP Switch Information menu displays the dome drive’s current DIP switch settings. This provides a way to remotely view the DIP switch
settings without removing the dome drive from the back box.
TION menu opens.
C3463M-C (7/11)21
Loading...
+ 53 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.