Pelco S66X User Manual

®

S66/S66X

Sun Shroud

Installation Manual

Manual C410M - 9/94

1.0 WARNINGS

Prior to installation and use of this product, the following
WARNINGS should be observed.

1. Installation and servicing should only be done by
Qualified Service Personnel and conform to all
Local codes.

2. Unless the unit is specifically marked as a NEMA
Type 3-6P enclosure, it is designed for Indoor use
only and it must not be installed where exposed to
rain and moisture.

4. Only use replacement parts recommended by
PELCO.

2.0 SCOPE

This manual covers the S66/S66X Sun Shroud for the
EH66 and EH66X Series Environmental Enclosures.

3.0 DESCRIPTION

The S66/S66X sun shroud is designed to protect the
EH66/EH66X enclosure from the direct rays of the sun
and reduce internal temperature approximately 10-15°.

The following items are required for proper installa­tion of the sun shroud assembly:

Quantity Item

6 Washer, Internal Star #10 SS

(Part # ZH10LWSIS)

6 Screw, 10-32 x 2" Pan Hd. Phil. SS

(Part # ZH10-32X2.00SPP)

6 Spacer, 5/16" DIA x 1.5" L, #10

Clear (Part # SPA8549)

Note: Use the six 10-32-UNC nuts and flat
washers provided with the enclosure assembly
(not included in this package).

PELCO • 300 W. Pontiac Way, Clovis, CA 93612-5699 • USA • [phone] or (1-559) 292-1981

FAX [phone] or (1-559) 292-3827 • DataFAX [phone] or (1-559) 292-0435

4.0 INSTALLATION

T o install the sun shroud, perform the following steps:

1. Unclamp the enclosure lid and remove.

2. Remove the six (6) screws from the enclosure

lid.

3. Align the screw holes in the sun shroud and en­closure lid.

Note: The sun shroud can be aligned in
either direction and fits over the top of the
enclosure and vent cap(s).

4. Install the screws with the spacers as illustrated
in Figure 1 and tighten.

Figure 1. Sun Shroud Assembly Diagram

2 PELCO Manual C410M — 9/94

5.0 WARRANTY AND RETURN
INFORMATION

WARRANTY

PELCO will repair or replace, without charge, any
merchandise proved defective in material or workman­ship for a period of one year after the date of shipment
(six months on all pan and tilts with auto scan and
medium duty scanners, and two years on Legacy®,
Intercept™ and CM9500/CM8500 Matrix products).
PELCO will warranty all replacement parts and repairs
for 90 days from the date of shipment. All goods for
warranty work shall be sent freight prepaid to our
Clovis, California facility. Repairs made necessary by
reason of misuse, alteration, normal wear, or accident
are not covered under this warranty. PELCO is not
liable for any incidental or consequential expenses or
liability incurred by the customer as a result of field
repair, installation, or any other reason.

The above warranty is in lieu of any other expressed or
implied warranty, condition, or guarantee by PELCO
of the equipment listed herein. PELCO makes no
warranties except for intended use and will not be liable
for any loss, damage, or costs arising, whether conse­quential or incidental, from the use of said merchan­dise.

RETURNS

In order to expedite parts returned to the factory for
repair or credit, please call the factory at (800) 289-
9100 or [phone] to obtain an authoriza­tion number (CA number if returned for credit, and RA
number if returned for repair). Goods returned for
repair or credit should be clearly identified with the
assigned CA/RA number and freight should be pre­paid. All merchandise returned for credit may be sub­ject to a 20% restocking and refurbishing charge.

Ship freight prepaid to: PELCO

300 West Pontiac Way
Clovis, CA 93612-5699

This warranty gives you specific legal rights. You may
also have additional rights, which are subject to varia­tion from state to state.

If a warranty repair is required, contact PELCO at
[phone] or [phone] for a
Repair Authorization number (RA), and provide the
following information:

1. Model and serial number

2. Date of shipment, P.O. number, Sales Order
number, or PELCO invoice number

3. Details of the defect or problem

If there is a dispute regarding the warranty of a product
which does not fall under the warranty conditions
stated above, please include a written explanation with
the product when returned.

Ship freight prepaid to: PELCO

300 West Pontiac Way
Clovis, CA 93612-5699

Method of return shipment shall be the same as method
by which the repair item is received by PELCO.

PELCO Manual C410M —9/94 3

®

PELCO

300 West Pontiac Way, Clovis, CA 93612-5699 [phone] • [phone]

FAX [phone] or [phone] • DataFAX [phone] or [phone]

(Product specifications subject to change without notice.)

C410M

4 PELCO Manual C410M — 9/94