Pelco RMA429 User Manual

®

RMA429

Rack Mount Kit

Installation/Operation

Manual C979M (1/93)

1.0 WARNINGS

Prior to installation and use of this product, the following
WARNINGS should be observed.

1. Installation and servicing should only be done by
Qualified Service Personnel and conform to all
Local codes.

2. Unless the unit is specifically marked as a NEMA
Type 3, 3R, 3S, 4, 4X, 6, or 6P enclosure, it is
designed for indoor use only and it must not be
installed where exposed to rain and moisture.

3. Use only installation methods and materials capable
of supporting four (4) times the maximum specified
load.

4. Only use replacement parts recommended by Pelco.

Please thoroughly familiarize yourself with the infor­mation in this manual prior to installation and opera­tion.

2.0 SCOPE

The information within this manual covers the installa­tion of the RMA429 Rack Mount Kit.

3.0 DESCRIPTION

The RMA429 Rack Mount Kit is designed to provide
rack mounting for single or dual Sanyo VM4509 and
HR4512 9" (22.86 cm) monitors.

This versatile rack will fit any standard 19 inch
(48.26 cm) wide console or rack configuration.

Pelco • 300 W. Pontiac Way, Clovis, CA 93612-5699 • USA • [phone] or (1-209) 292-1981

FAX [phone] or (1-209) 292-3827 • DataFAX [phone] or (1-209) 292-0435

International customers call (1-209) 292-1981 or FAX [phone]

4.0 INSTALLATION

1. Remove rubber feet on bottom of monitor.

2. Install monitor through rear of rack and align holes
in bottom of monitor with mounting holes in rack.

3. Use hardware from rubber feet to mount monitor
to rack.

4. Install rack and monitor as an assembly into con­sole and make any required electrical connections.

5. Hold into place, aligning mounting holes of the
RMA429 with mounting holes in console, and in­sert and tighten required fasteners (not supplied).
If only a single monitor is used, install cover plate
up against window frame and then insert fasteners
and tighten.

2 Pelco Manual C979M (1/93)

5.0 SPECIFICATIONS

Dimensions: See Figure 1

Construction: 16-gauge steel

Weight: 5.56 lbs (2.50 kg)

Figure 1. RMA429 Dimension Drawing

Pelco Manual C979M (1/93) 3

6.0 WARRANTY AND RETURN

INFORMATION

WARRANTY

If a warranty repair is required, contact Pelco at (800)
289-9100 or [phone] for a Repair

Authorization number (RA), and provide the following
information:

Pelco will repair or replace, without charge, any
merchandise proved defective in material or
workmanship for a period of one (1) year after the date
of shipment. Exceptions to this warranty are as noted
below:

• Two (2) years on all standard motorized and fixed
focal length lenses.

• Two (2) years on Legacy®, Intercept®, CM8500/
CM9500/CM9750 Matrix and DF8 Fixed Dome
products.

• Two (2) years on WW5700 series window wiper
(excluding wiper blades).

• Two (2) years on cameras.

• Six (6) months on all pan and tilts, scanners or
preset lenses used in continuous motion
applications (e.g., preset scan, tour and auto scan
modes).

Pelco will warranty all replacement parts and repairs
for 90 days from the date of shipment. All goods for
warranty work shall be sent freight prepaid to our
Clovis, California facility. Repairs made necessary by
reason of misuse, alteration, normal wear, or accident
are not covered under this warranty. Pelco is not liable
for any incidental or consequential expenses or liability
incurred by the customer as a result of field repair,
installation, or any other reason.

1. Model and serial number

2. Date of shipment, P.O. number, Sales Order
number, or Pelco invoice number

3. Details of the defect or problem

If there is a dispute regarding the warranty of a product
which does not fall under the warranty conditions
stated above, please include a written explanation with
the product when returned.

Ship freight prepaid to: Pelco

300 West Pontiac Way
Clovis, CA 93612-5699

Method of return shipment shall be the same as method
by which the repair item is received by Pelco.

RETURNS

In order to expedite parts returned to the factory for
repair or credit, please call the factory at (800) 289-
9100 or [phone] to obtain an authorization
number (CA number if returned for credit, and RA
number if returned for repair). Goods returned for
repair or credit should be clearly identified with the
assigned CA/RA number and freight should be prepaid.
All merchandise returned for credit may be subject to
a 20% restocking and refurbishing charge.

Ship freight prepaid to: Pelco

300 West Pontiac Way
Clovis, CA 93612-5699

The above warranty is in lieu of any other expressed or
implied warranty, condition, or guarantee by Pelco of
the equipment listed herein. Pelco makes no warranties
except for intended use and will not be liable for any
loss, damage, or costs arising, whether consequential
or incidental, from the use of said merchandise.

This warranty gives you specific legal rights. You may
also have additional rights, which are subject to variation
from state to state.

4 Pelco Manual C979M (1/93)