Pelco RMA121SU User Manual

®

RMA131SU

Rack Mount Kit

Installation/Operation Manual

C917M (5/96)

1.0 WARNINGS

Prior to installation and use of this product, the follow­ing WARNINGS should be observed.

1. Installation and servicing should only be done by
Qualified Service Personnel and conform to all
Local codes.

2. Unless the unit is specifically marked as a NEMA
Type 3, 3R, 3S, 4, 4X, 6, or 6P enclosure, it is de­signed for indoor use only and it must not be in­stalled where exposed to rain and moisture.

3. Only use replacement parts recommended by
Pelco.

2.0 SCOPE

The information within this manual covers the installa­tion of the RMA131SU Rack Mount Kit.

Installation should be in accordance with all applicable
local and national electric codes, utilizing approved ma­terials only.

Please thoroughly familiarize yourself with the infor­mation in this manual prior to installation and opera­tion.

3.0 DESCRIPTION

The RMA131SU Rack Mount Kit is designed to pro­vide rack mounting for a single JVC TM-131SU 13"
monitor.

This versatile rack will fit any standard 19 inch wide
console or rack configuration.

PELCO • 3500 Pelco Way, Clovis, CA 93612-5699 • USA • [phone] or (1-559) 292-1981

FAX [phone] or (1-559) 292-3827

4.0 SPECIFICATIONS

Dimensions: See Figure 1

Construction: 14 and 16-gauge steel

To install the rack kit and monitor, perform the follow­ing steps:

1. Assemble the rack as shown in Figure 2 using the
supplied hardware.

Weight: 4 lbs 10 oz. (2.08 kg)

5.0 INSTALLATION

The RMA131SU rack kit is supplied unassembled. The
following hardware is provided for use in assembling
the rack kit.

Qty Description

6 8-32 Hex nuts
6 #8 Lock Washers

While assembling, install all hardware loosely un­til all components are attached and then finish by
tightening all hardware.

2. Slide the monitor into the rack, tight against the
rear stop.

3. Install rack and monitor as an assembly into con­sole and make any required electrical connections.

4. Hold into place, aligning mounting holes of the
RMA131SU with mounting holes in console, and
insert and tighten required fasteners (not supplied).

NOTE: VALUES IN PARENTHESES ARE CENTIMETERS; ALL OTHERS ARE INCHES.

Figure 1. RMA131SU Dimension Drawing

2 Pelco Manual C917M (5/96)

6.0 RMA131SU EXPLODED ASSEMBLY DIAGRAM

Figure 2. RMA131SU Rack Kit Assembly

6.1 RMA131SU EXPLODED DIAGRAM PARTS LIST

Item # Qty Description Part Number

11 Base, Rack mount RMA131SU4000COMP
21 Side, Left rack mount RMA131SU4001COMP
31 Side, Right rack mount RMA131SU4002COMP

Pelco Manual C917M (5/96) 3

7.0 WARRANTY AND RETURN
INFORMATION

WARRANTY

Pelco will repair or replace, without charge, any merchandise proved
defective in material or workmanship for a period of one year after the date
of shipment.

Exceptions to this warranty are as noted below:

• Five years on FT/FR8000 Series fiber optic products.

• Three years on Genex

keyboard).

• Three years on Camclosure

CC3701H-2, CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2,
and MC3651H-2X camera models, which have a five-year warranty.

• Two years on standard motorized or fixed focal length lenses.

• Two years on Legacy

DF5/DF8 Series fixed dome products.

• Two years on Spectra

ing when used in continuous motion applications.

• Two years on Esprit

wiper blades).

• Eighteen months on DX Series digital video recorders, NVR300

Series network video recorders, and Endura
network-based video products.

• One year (except video heads) on video cassette recorders (VCRs).

Video heads will be covered for a period of six months.

• Six months on all pan and tilts, scanners or preset lenses used in

continuous motion applications (that is, preset scan, tour and auto scan
modes).

Pelco will warrant all replacement parts and repairs for 90 days from the
date of Pelco shipment. All goods requiring warranty repair shall be sent
freight prepaid to Pelco, Clovis, California. Repairs made necessary by
reason of misuse, alteration, normal wear, or accident are not covered
under this warranty.

Pelco assumes no risk and shall be subject to no liability for damages or
loss resulting from the specific use or application made of the Products.
Pelco’s liability for any claim, whether based on breach of contract,
negligence, infringement of any rights of any party or product liability,
relating to the Products shall not exceed the price paid by the Dealer to
Pelco for such Products. In no event will Pelco be liable for any special,
incidental or consequential damages (including loss of use, loss of profit
and claims of third parties) however caused, whether by the negligence
of Pelco or otherwise.

The above warranty provides the Dealer with specific legal rights. The
Dealer may also have additional rights, which are subject to variation from
state to state.

If a warranty repair is required, the Dealer must contact Pelco at (800) 289­9100 or [phone] to obtain a Repair Authorization number (RA),
and provide the following information:

1. Model and serial number

2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice

number

3. Details of the defect or problem

If there is a dispute regarding the warranty of a product which does not fall
under the warranty conditions stated above, please include a written
explanation with the product when returned.
Method of return shipment shall be the same or equal to the method by
which the item was received by Pelco.

®

Series products (multiplexers, server, and

®

and fixed camera models, except the

®

, CM6700/CM6800/CM9700 Series matrix, and

®

, Esprit®, ExSite™, and PS20 scanners, includ-

®

and WW5700 Series window wiper (excluding

™

Series distributed

RETURNS

In order to expedite parts returned to the factory for repair or credit, please
call the factory at [phone] or [phone] to obtain an
authorization number (CA number if returned for credit, and RA number
if returned for repair).

All merchandise returned for credit may be subject to a 20% restocking
and refurbishing charge.

Goods returned for repair or credit should be clearly identified with the
assigned CA or RA number and freight should be prepaid. Ship to the
appropriate address below.

If you are located within the continental U.S., Alaska, Hawaii or Puerto
Rico, send goods to:

If you are located outside the continental U.S., Alaska, Hawaii or Puerto
Rico and are instructed to return goods to the USA, you may do one of the
following:
If the goods are to be sent by a COURIER SERVICE, send the goods to:

If the goods are to be sent by a FREIGHT FORWARDER, send the goods
to:

Service Department
Pelco
3500 Pelco Way
Clovis, CA 93612-5699

Pelco
3500 Pelco Way
Clovis, CA 93612-5699 USA

Pelco c/o Expeditors
473 Eccles Avenue
South San Francisco, CA 94080 USA
Phone: [phone]
Fax: [phone]

®

Pelco

300 West Pontiac Way, Clovis, CA 93612-5699

[phone] • [phone]

FAX [phone] or [phone]

International customers call 1-559-292-1981 or

FAX [phone]

Pelco, the Pelco logo, Camclosure, Esprit,
Genex, Legacy, and Spectra are registered
trademarks of Pelco.
Endura and ExSite are trademarks of Pelco.

© Copyright 1996, Pelco. All rights reserved.

(Product specifications subject to change

without notice.)

C917M

4 Pelco Manual C917M (5/96)