Pelco RM2001SD User Manual

C1957M (3/99) RM2001 Series VCR Rack Mount
®
3500 Pelco Way Clovis, CA 93612-5699 USA
In North America & Canada: Tel (800) 289-9100 FAX (800) 289-9150
International Customers: Tel (1-559) 292-1981 FAX (1-559) 348-1120
www.pelco.com
IMPORTANT SAFEGUARDS AND WARNINGS
Prior to installation and use of this product, the following WARNINGS should be observed.
1. Installation and servicing should be done by qualified installation and service personnel
2. Installation should be done according to all local and national electrical and mechanical
3. Use only installation methods and materials capable of supporting four times the
Please thoroughly familiarize yourself with the information in this manual prior to installation and operation.
DESCRIPTION
The RM2001 Rack Mount holds a single Pelco TLR Series VCR. This versatile rack mount will fit any standard 19-inch (48.26 cm) wide console or rack configuration. The RM2001SD model is the same as the RM2001, but is supplied with a lockable security door (not installed) having a smoked Lexan® window. The rack mounts have a black polyester powder coat finish.
MODELS
RM2001 Rack mount for TLR Series VCR. Does not include front door. RM2001SD Rack mount for TLR Series VCR. Includes locking front door.
INSTALLATION
NOTE:
A security door (item 1),
To install the RM2001 Series VCR Rack Mount:
backstop bracket (item 2), and five 6-32 Phillips screws (item 3) are shipped as loose equipment
Steps 1 and 2 apply to both the RM2001 and RM2001SD VCR Rack Mounts:
1. Place the rack mount in the console or equipment rack, align the mounting holes, and
for the RM2001SD model (refer to Figure 1). The backstop bracket should be installed in the
2. Set the VCR into the rack mount, pushing it back until it stops at the backstop bracket
hole provided in the rear of the rack mount base whenever the rack mount will be used
out
the security door. If the
with-
Step 3 applies to the RM2001SD VCR Rack Mount only:
3. Attach the security door (item 1) to the front of the rack mount with four 6-32 Phillips
backstop bracket is installed when using the security door, the VCR will protrude and not allow the door to close.
Table A. RM2001SD VCR Rack Mount
Loose Parts List
only.
codes, using only approved materials.
maximum weight of the VCR and rack mount.
insert and tighten the required fasteners (not supplied).
(RM2001 model) or the rear lip of the rack mount base (RM2001SD model).
screws (item 3). Refer to Figure 1 and Table A.
3
RM2001
2
2
SHIPPED LOOSE FOR RM2001SD
INSTALLED FOR RM2001
Item Qty Description
11Security door 21Backstop bracket (see note) 35Phillips screws, 6-32 x 1/4 in.
3
1
Figure 1. RM2001 Series VCR Rack Mount
SPECIFICATIONS
Construction: Steel
Finish: Black polyester powder coat
Dimensions
Inside: 3.87 in. H x 16.73 in. W x 12.82 in. D (9.83 x 42.49 x 32.56 cm) Outside: 5.22 in. H x 18.98 in. W x 13.16 in. D (13.26 x 48.21 x 33.43 cm)
Weight: Unit Shipping
RM2001 5.5 lb (2.5 kg) 8.0 lb (3.6 kg) RM2001SD 6.9 lb (3.1 kg) 10.0 lb (4.5 kg)
(Design and product specifications subject to change without notice.)
PRODUCT WARRANTY AND RETURN INFORMATION
WARRANTY
Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment.
Exceptions to this warranty are as noted below:
• Five years on FT/FR8000 Series fiber optic products.
®
• Three years on Genex
• Three years on Camclosure CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2, and MC3651H-2X camera models, which have a five-year warranty.
•Two years on standard motorized or fixed focal length lenses.
•Two years on Legacy fixed dome products.
•Two years on Spectra continuous motion applications.
•Two years on Esprit
• Eighteen months on DX Series digital video recorders, NVR300 Series network video recorders, and Endura
• One year (except video heads) on video cassette recorders (VCRs). Video heads will be covered for a period of six months.
• Six months on all pan and tilts, scanners or preset lenses used in continuous motion applications (that is, preset scan, tour and auto scan modes).
Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco shipment. All goods requiring warranty repair shall be sent freight prepaid to Pelco, Clovis, California. Repairs made necessary by reason of misuse, alteration, normal wear, or accident are not covered under this warranty.
Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from the specific use or application made of the Products. Pelco’s liability for any claim, whether based on breach of contract, negligence, infringement of any rights of any party or product liability, relating to the Products shall not exceed the price paid by the Dealer to Pelco for such Products. In no event will Pelco be liable for any special, incidental or consequential damages (including loss of use, loss of profit and claims of third parties) however caused, whether by the negligence of Pelco or otherwise.
The above warranty provides the Dealer with specific legal rights. The Dealer may also have additional rights, which are subject to variation from state to state.
Series products (multiplexers, server, and keyboard).
®
and fixed camera models, except the CC3701H-2,
®
, CM6700/CM6800/CM9700 Series matrix, and DF5/DF8 Series
®
, Esprit®, ExSite™, and PS20 scanners, including when used in
®
and WW5700 Series window wiper (excluding wiper blades).
Series distributed network-based video products.
If a warranty repair is required, the Dealer must contact Pelco at (800) 289-9100 or (559) 292-1981 to obtain a Repair Authorization number (RA), and provide the following information:
1. Model and serial number
2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number
3. Details of the defect or problem
If there is a dispute regarding the warranty of a product which does not fall under the warranty conditions stated above, please include a written explanation with the product when returned.
Method of return shipment shall be the same or equal to the method by which the item was received by Pelco.
RETURNS
In order to expedite parts returned to the factory for repair or credit, please call the factory at (800) 289-9100 or (559) 292-1981 to obtain an authorization number (CA number if returned for credit, and RA number if returned for repair).
All merchandise returned for credit may be subject to a 20% restocking and refurbishing charge.
Goods returned for repair or credit should be clearly identified with the assigned CA or RA number and freight should be prepaid. Ship to the appropriate address below.
If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico, send goods to:
Service Department Pelco 3500 Pelco Way Clovis, CA 93612-5699
If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico and are instructed to return goods to the USA, you may do one of the following:
If the goods are to be sent by a COURIER SERVICE, send the goods to:
Pelco 3500 Pelco Way Clovis, CA 93612-5699 USA
If the goods are to be sent by a FREIGHT FORWARDER, send the goods to:
Pelco c/o Expeditors 473 Eccles Avenue South San Francisco, CA 94080 USA Phone: 650-737-1700 Fax: 650-737-0933
REVISION HISTORY
Manual # Date Comments
C1957M 3/99 Original version.
Pelco, the Pelco logo, Camclosure, Esprit, Genex, Legacy, and Spectra are registered trademarks of Pelco. © Copyright 1999, Pelco. Endura and ExSite are trademarks of Pelco. All rights reserved.
Loading...