Page 1
INSTALLATION
Rack Mount Chassis
RK5000PS-5U
For Endura Modules
C1615M-C (9/06)
Page 2
Contents
Regulatory Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Front View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Back View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Mounting a Chassis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Installing a Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Installing a Blank Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Installing an Internal Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Replacing an Internal Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Replacing a Fan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
List of Illustrations
1 Package Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2 RK5000PS-5U Front View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
3 RK5000PS-5U Back View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
4 Mounting an RK5000PS-5U into a Rack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
5 Inserting Cage Nuts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
6 Endura IP System Module Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
7 Blank Module Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
8 Power Supply Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
9 Fan Baffle Thumbscrews . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
10 Fan Baffle Back Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
11 Fan Screws . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
12 Fan Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
2 C1615M-C (9/06)
Page 3
Regulatory Notices
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
RADIO AND TELEVISION INTERFERENCE
This equipment has been tested and found to comply with the limits of a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may
cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in
which case the user will be required to correct the interference at his own expense.
Changes and Modifications not expressly approved by the manufacturer or registrant of this equipment can void your authority to operate this
equipment under Federal Communications Commission’s rules.
In order to maintain compliance with FCC regulations shielded cables must be used with this equipment. Operation with non-approved
equipment or unshielded cables is likely to result in interference to radio and television reception.
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.
C1615M-C (9/06) 3
Page 4
Before You Begin
Please familiarize yourself with the parts list before installing the unit.
PARTS LIST
Qty Description
1 RK5000PS-5U rack mount chassis with fan baffle for thermal management
1 USA standard power cord
1 European standard power cord
1 UK standard power cord
10 Thumbscrews for secondary standoffs
4 Screws with washers, 10-32 x 0.750-inch, Phillips, pan head
4 Cage nuts, 10-32
1 RK5000PS-5U Installation manual
1 RK5000PS-5U Safety instructions
PACKAGE CONTENTS
The following diagrams show the contents of the box. When installing the RK5000PS-5U, refer to these diagrams.
SHIPPING BOX
RK5000PS-5U
USA STANDARD
POWER CORD
(110 VAC)
1 EA.
SHOWN ACTUAL SIZE
EUROPEAN
STANDARD POWER
CORD (220 VAC)
1 EA.
THUMBSCREW
10 EA.
PHILLIPS PAN HEAD SCREW
WITH WASHER
10-32 x 0.750
4 EA.
Figure 1. Package Components
4 C1615M-C (9/06)
CAGE NUT
10-32
4 EA.
INSTALLATION MANUAL
SAFETY INSTRUCTIONS
UK
STANDARD POWER
CORD (250 VAC)
1 EA.
Page 5
Description
The RK5000PS-5U rack mount chassis supports Endura IP system modules. The chassis has 12 slots for single-width modules and 2 slots for an
internal, double-width power supply. You can fill the empty slots with single-width blank modules (RK5001B-4U).
The RK5000PS-5U chassis includes a fan baffle for cooling the modules. The fan baffle makes the chassis 5 rack units (RU) high even though the
modules are 4 RU high. You can mount the chassis into an EIA-standard, 19-inch (48.26 cm) rack.
For redundancy, you can use the optional 1 RU high external power supply (EPS5000-300). It provides redundant power for up to two fully
populated RK5000PS-5U chassis and can be mounted into a rack.
The internal power supply has a relay output connector that is directly wired to the power and is a normally closed (N.C.) dry contact. If the power
supply fails, the relay opens.
FRONT VIEW
Fan Baffle
Rack Ear (2)
Power Supply with Handle
Module Slot (12)
Figure 2. RK5000PS-5U Front View
C1615M-C (9/06) 5
Page 6
BACK VIEW
Thumbscrew for Fastening Modules (12)
Fan (10)
10-Pin Power Connector
Relay Output Connector
AC Power Cord Connector
Power Switch
Spare Fuse
Figure 3. RK5000PS-5U Back View
6 C1615M-C (9/06)
Page 7
Installation
MOUNTING A CHASSIS
The RK5000PS-5U chassis can be mounted into an EIA-standard, 19-inch rack. To mount the chassis into a rack, follow these steps and refer to
Figure 4.
1. Insert the chassis into the rack.
2. Secure the chassis to the rack with the supplied screws and washers.
Figure 4. Mounting an RK5000PS-5U into a Rack
If installing the RK5000PS-5U into a square-hole rack, insert two cage nuts in each side of the square-hole rack as shown in Figure 5.
CAGE NUT
Figure 5. Inserting Cage Nuts
C1615M-C (9/06) 7
Page 8
INSTALLING A MODULE
You can install up to 12 single-width modules into the RK5000PS-5U. To install a module, follow these steps and refer to Figure 6.
1. Insert the module into an empty slot of the chassis. The two slots on the right are for the power supply.
2. Secure the module by tightening the thumbscrew on the back of the chassis.
NOTE: Some versions of the Endura module do not have a threaded screw hole for the thumbscrew in the primary threaded standoff to engage.
If the threaded screw hole aligns with the secondary standoff, use one of the supplied thumbscrews.
SECONDARY
THREADED
STANDOFF
PRIMARY
THREADED
STANDOFF
Figure 6. Endura IP System Module Installation
8 C1615M-C (9/06)
Page 9
INSTALLING A BLANK MODULE
Single-width blank modules can be used to fill the empty module slots on the chassis. To install a blank module, follow these steps and refer to
Figure 7.
1. Insert the blank module into the empty slot on the chassis.
2. Secure the blank module by tightening the thumbscrew on the back of the chassis.
Figure 7. Blank Module Installation
C1615M-C (9/06) 9
Page 10
INSTALLING AN INTERNAL POWER SUPPLY
The double-width internal power supply must be installed into the RK5000PS-5U chassis. To install the internal power supply, follow these steps
and refer to Figure 8.
1. Insert the power supply into the rack.
2. Secure the power supply by tightening the two thumbscrews on the front of the chassis.
3. Plug in the power cord.
4. Turn on the power supply.
Figure 8. Power Supply Installation
10 C1615M-C (9/06)
Page 11
Service
REPLACING AN INTERNAL POWER SUPPLY
You can easily replace the internal power supply in the RK5000PS-5U with a replacement (RK5PWR-300). You will know if there is a problem
with the power supply because the blue Pelco badge on the front panel will turn off. Before replacing the power supply, check the fuse. It can be
replaced easily with the supplied spare. If the fuse is not the problem, then follow these steps and refer to Figure 8 to replace the power supply.
1. Unplug the AC power cord.
2. Unscrew the two thumbscrews on the front of the chassis that hold the power supply.
3. Pull the power supply out of the chassis using the handle.
4. Insert the new power supply.
5. Secure the power supply by tightening the two thumbscrews on the front of the chassis.
6. Plug in the AC power cord.
7. Turn on the power switch.
C1615M-C (9/06) 11
Page 12
REPLACING A FAN
The fan baffle on the RK5000PS-5U has 10 fans. These fans can be replaced easily in case of failure. To replace a fan, follow these steps and
refer to Figures 9-12.
1. Unscrew the two thumbscrews on the back of the fan baffle.
2. Lower the back panel until the fans are exposed.
3. Unscrew the two screws that hold the fan in place.
4. Unplug the red 2-pin connector from the bus board.
5. Remove the failed fan and insert the new one.
6. Plug in the 2-pin connector.
7. Tighten the two screws to hold the fan in place.
WARNING: Do not overtighten the two screws. Doing so can crack the plastic fan case.
8. Raise the back panel and tighten both thumbscrews.
Figure 9. Fan Baffle Thumbscrews
Figure 10. Fan Baffle Back Panel
12 C1615M-C (9/06)
Page 13
Figure 11. Fan Screws
Figure 12. Fan Connector
C1615M-C (9/06) 13
Page 14
Specifications
ELECTRICAL
Input Voltage 100-240 VAC, 50-60 Hz, autoranging
Output Voltage 12 VDC
Power Consumption Operating Maximum (non-inclusive of components within the rack)
100 VAC 110 W, 454 BTU/H
115 VAC 115 W, 471 BTU/H
220 VAC 220 W, 492 BTU/H
Fuse 4 amps/250 V
Redundant Capability Yes with optional EPS5000-300 power supply
MECHANICAL
Number of Slots 12 for modules and 2 for power supply
Module Orientation Vertical
Rack Units 5 (includes fan baffle)
Construction Aluminum
Finish Black
ENVIRONMENTAL
Ambient Temperature 70° to 74°F (21° to 23°C)
Operating Temperature 32° to 122°F (0° to 50°C) at air intake of unit
Storage Temperature -40° to 149°F (-40° to 65°C)
Operating Humidity 20% to 80% noncondensing
Maximum Humidity Gradient 10% per hour
Operating Altitude -50 ft to 10,000 ft (-16 m to 3,048 m)
Operating Vibration 0.25 G at 3 Hz to 200 Hz at a sweep rate of 0.5 octaves/minute
GENERAL
Dimensions 8.72" H x 17.70" W x 15.50" D (22.15 x 44.96 x 39.37 cm)
Mounting Fits 19-inch, EIA-standard rack
Unit Weight 12.7 lb (5.76 kg), with power supply
37.8 lb (17.15 kg), fully populated
14 C1615M-C (9/06)
Page 15
PRODUCT WARRANTY AND RETURN INFORMATION
WARRANTY
Pelco will repair or replace, without charge, any merchandise proved defective in material or
workmanship for a period of one year after the date of shipment.
Exceptions to this warranty are as noted below:
• Five years on FR/FT/FS Series fiber optic products and TW3000 Series unshielded twisted
pair transmission products.
• Three years on Genex
• Three years on Camclosure
CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2, and MC3651H-2X camera models,
which have a five-year warranty.
• Three years on PMCL200/300/400 Series LCD monitors.
• Two years on standard motorized or fixed focal length lenses.
• Two years on Legacy
fixed dome products.
• Two years on Spectra
continuous motion applications.
• Two years on Esprit and WW5700 Series window wiper (excluding wiper blades).
• Two years (except lamp and color wheel) on Digital Light Processing (DLP
The lamp and color wheel will be covered for a period of 90 days. The air filter is not
covered under warranty.
• Eighteen months on DX Series digital video recorders, NVR300 Series network video
recorders, and Endura
• One year (except video heads) on video cassette recorders (VCRs). Video heads will be
covered for a period of six months.
• Six months on all pan and tilts, scanners or preset lenses used in continuous motion
applications (that is, preset scan, tour and auto scan modes).
Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco
shipment. All goods requiring warranty repair shall be sent freight prepaid to Pelco, Clovis,
California. Repairs made necessary by reason of misuse, alteration, normal wear, or accident
are not covered under this warranty.
Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from
the specific use or application made of the Products. Pelco’s liability for any claim, whether
based on breach of contract, negligence, infringement of any rights of any party or product liability, relating to the Products shall not exceed the price paid by the Dealer to Pelco for such
Products. In no event will Pelco be liable for any special, incidental or consequential damages
(including loss of use, loss of profit and claims of third parties) however caused, whether by
the negligence of Pelco or otherwise.
The above warranty provides the Dealer with specific legal rights. The Dealer may also have
additional rights, which are subject to variation from state to state.
®
Series products (multiplexers, server, and keyboard).
®
and fixed camera models, except the CC3701H-2,
®
, CM6700/CM6800/CM9700 Series matrix, and DF5/DF8 Series
®
, Esprit®, ExSite™, and PS20 scanners, including when used in
®
) displays.
™
Series distributed network-based video products.
If a warranty repair is required, the Dealer must contact Pelco at (800)þ289-9100 or
(559) 292-1981 to obtain a Repair Authorization number (RA), and provide the following
information:
1. Model and serial number
2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number
3. Details of the defect or problem
If there is a dispute regarding the warranty of a product which does not fall under the
warranty conditions stated above, please include a written explanation with the product when
returned.
Method of return shipment shall be the same or equal to the method by which the item was
received by Pelco.
RETURNS
In order to expedite parts returned to the factory for repair or credit, please call the factory at
(800) 289-9100 or (559) 292-1981 to obtain an authorization number (CA number if returned for
credit, and RA number if returned for repair).
All merchandise returned for credit may be subject to a 20% restocking and refurbishing
charge.
Goods returned for repair or credit should be clearly identified with the assigned CA or RA
number and freight should be prepaid. Ship to the appropriate address below.
If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico, send goods to:
Service Department
Pelco
3500 Pelco Way
Clovis, CA 93612-5699
If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico and are
instructed to return goods to the USA, you may do one of the following:
If the goods are to be sent by a COURIER SERVICE, send the goods to:
Pelco
3500 Pelco Way
Clovis, CA 93612-5699 USA
If the goods are to be sent by a FREIGHT FORWARDER, send the goods to:
Pelco c/o Expeditors
473 Eccles Avenue
South San Francisco, CA 94080 USA
Phone: 650-737-1700
Fax: 650-737-0933
The materials used in the manufacture of this document and its components are compliant to the requirements of Directive 2002/95/EC.
This equipment contains electrical or electronic components that must be recycled properly to comply with Directive 2002/96/EC of the European Union
regarding the disposal of waste electrical and electronic equipment (WEEE). Contact your local dealer for procedures for recycling this equipment.
REVISION HISTORY
Manual # Date Comments
C1615M 4/05 Original version.
C1615M-A 9/05 Added Before You Begin section. Added Figure 5. Revised Power Consumption in Specifications.
C1615M-B 1/06 Revised rack illustrations to show two shelf dividers.
C1615M-C 9/06 Revised specifications.
Pelco, the Pelco logo, Spectra, Genex, Esprit, Cam closure, and Legacy are registered trademarks of Pelco. © Copyright 2006, Pelco. All rights reserved.
Endura and ExSite are trademarks of Pelco.
DLP is a registered trademark of Texas Instruments, Inc.
Page 16
Worldwide Headquarters
3500 Pelco Way
Clovis, California 93612 USA
USA & Canada
Tel: 800/289-9100
Fax: 800/289-9150
International
Tel: 1-559/292-1981
Fax: 1-559/348-1120
www.pelco.com
ISO9001
Australia|Canada|Finland|France|Italy|Russia|Singapore|Spain|Sweden|The Netherlands|United Arab Emirates|United Kingdom|United States
Loading...