Pelco PT680-24P Specsheet

PRODUCT SPECIFICATION

PT680-24P Pan/Tilt

OUTDOOR, MEDIUM DUTY, FEEDTHROUGH

Product Features

• 24 VAC Operation

• Outdoor Applications

• Adjustable Worm-Gear Final Drive

• Prewired for Zoom Lens, Camera Power, Enclosure Power, and Video

• Optional Preset Positioning Available

• Maximum Load 50 lb (22.7 kg)

The

PT680-24P

a maximum load of 50 pounds (22.7 kg). The unit is factory prewired for feedthrough of the motorized zoom lens, camera power, enclosure power, and video signals. All connections are made at the input connector, eliminating the need for wiring harnesses made in the ﬁeld. This feature greatly reduces installation time, while increasing the reliability and serviceability of the system.

The

PT680-24P

minimize backlash and prevent wind drift. The drives are fully adjustable for wear.

An aluminum and coated-steel housing limits the effects of corrosion in outdoor applications. The with our EH4700 Series environmental enclosures.

is a medium duty outdoor pan/tilt designed to accept

features rugged worm-gear ﬁnal drive assemblies to

PT680-24P

is recommended for use

5.87

(14.91)

2.93

(7.44)

Ø 0.312 (0.79) 4X

7.00

(17.78)

9.87

(25.07)

10.87

(27.61)

camera solutions

0.281 X 0.656 OBROUND 2X (0.71 X 1.67)

Ø 0.281 (0.71)

2.37

5.00

(6.02)

(12.70)

11.50

(29.21)

6.00

(15.24)

Ø 0.390 X 0.80 (0.99 X 2.03) SLOT 4X EQ SP ON A Ø4.75 (12.06) B.C.

NOTE: VALUES IN PARENTHESES ARE CENTIMETERS;

ALL OTHERS ARE INCHES.

International Standards

Organization Registered Firm;

ISO 9001 Quality System

C337 / REVISED 8-17-10

41” (104.14) LONG FEEDTHROUGH CABLE

TECHNICAL SPECIFICATIONS

MODEL

PT680-24P Medium duty outdoor pan/tilt, 24 VAC

operation, supplied with factory-assembled pigtail cable and connector.

MECHANICAL

Pan 0 to 355° movement in horizontal plane

Speed 9°/sec ±1° Torque 10 ft-lb with speciﬁed voltage

Tilt ±90° movement in vertical plane

Speed 3°/sec ±0.5°

Maximum Load 50 lb (22.7 kg) at 5" (12.7 cm) from tilt table

surface to center of gravity

Gearing Adjustable worm-gear ﬁnal drive to prevent

drift and minimize backlash

Bearings

Pan Heavy duty ball bearings Tilt Oilite bronze bushing

Duty Cycle 50% duty cycle; 30 minute rating

ELECTRICAL

Input Voltage 24 VAC, 50/60 Hz Power Requirements

Pan 0.9 A (21.6 VA)

Tilt 1 A (24.0 VA) Connectors AMP CPC type, mate supplied Motors Two-phase induction type, instantaneous

Limit Switches 5 A each (pan and tilt) Conductor Requirements 13, plus ground and coaxial cable Maximum Operating Distances*

5 Conductors 20 AWG (0.5 mm

6 Conductors† 20 AWG (0.5 mm2) 118 ft (35 m)

*Distances are calculated with both motors (pan and tilt) running and

assuming a 10% voltage drop.

†

Using 2-wire motor common.

reversing

) 60 ft (18 m) 18 AWG (1.0 mm2) 95 ft (29 m) 16 AWG (1.5 mm2) 155 ft (47 m)

18 AWG (1.0 mm2) 185 ft (56 m) 16 AWG (1.5 mm2) 295 ft (90 m)

GENERAL

Construction Aluminum plate, all parts corrosion protected Finish Gray polyester powder coat Environment Outdoor operation;

–10° to 120°F (–23° to 49°C) Unit Weight 21.26 lb (9.6 kg) Shipping Weight 26 lb (11.7 kg)

CERTIFICATIONS/RATINGS

• UL Listed

• Meets NEMA Type 3R standards

RECOMMENDED CONTROLS

Coaxitron

or Matrix Refer to individual speciﬁcation sheets for

information. MPT24DT Desktop control for 24 VAC pan/tilt. MPTAZ24DT Desktop pan/tilt and zoom lens control with

auto/random scan for 24 VAC pan/tilts.

RECOMMENDED ENCLOSURES

EH4700 Series Environmental enclosure EH5700 Series Environmental enclosure

RECOMMENDED MOUNTS

PA2000 Adapter plate; required when using WM2000. PM2000, PM2010 Ceiling/pedestal mount; maximum load

ST1 Support strut for WM2000/PM2000/ PM2010. WM2000 Wall mount; maximum load 75 lb (34 kg).

125 lb (56.7 kg).

When used with ST1 support strut, maximum

load is increased to 150 lb (68 kg). Must be

used with PA2000 adapter.

Pelco, Inc. Worldwide Headquarters:

3500 Pelco Way, Clovis, California 93612-5699 USA

USA & Canada International www.pelco.com

Tel: (800) 289-9100 • FAX: (800) 289-9150

Tel: +1 (559) 292-1981 • FAX: +1 (559) 348-1120

Pelco, the Pelco logo, and other trademarks associated with Pelco products referred

to in this publication are trademarks of Pelco, Inc. or its afﬁliates. All other product names and services are the property of their respective companies. Product speciﬁcations and availability are subject to change without notice.