Pelco PS7-24 User Manual

C350SM (10/99)
PS7 and PS7-24
Light-Duty Scanners

3500 Pelco Way,
Clovis, CA 93612-5699
USA

In North America & Canada:
Tel [phone]
FAX [phone]

International Customers:
Tel [phone]
FAX [phone]

www.pelco.com

This maintenance/service manual consists of an exploded assembly diagram, wiring diagrams,
and parts lists. Use this manual when ordering replacement parts for PS7/PS7-24 Scanners.

MAINTENANCE

Under normal operating conditions and usage, maintenance of this equipment is not necessary.
The scanners in the PS7 Series require no lubrication, and the motors are both clutch and im­pedance protected from overload. The outside of the scanner may be cleaned by wiping with a
dry cloth or spraying with clean air pressure. Do not use spray cleaners or water.

EXPLODED ASSEMBLY DIAGRAM

Figure 1. PS7 and PS7-24 Exploded Assembly

PS7 and PS7-24 Parts List

Item Qty Description Part Number

12Pan limit stop 58010006
22Clutch PS710000
31Drag clutch PS710002
42Limit friction disk PS710001
51Switch actuator PS74015COMP
61Switch bracket PS74016COMP
71PC board assembly

120 VAC (model PS7) PS71004COMP

24 VAC (model PS7-24) PS71003COMP
81Switch SWI11-314
91Rubber grommet GRO2170

10 1 Bottom plate PS74100COMP
11 1 Top plate PS74101COMP
12 1 Body PS74002
13 1 Limit support PS74003COMP
14 1 Mounting plate PS74004COMP
15 4 Spacer ZH30-0202-0404
16 1 Pressure plate PS74009COMP
17 1 Thrust collar PS74011COMP
18 1 Bearing holder PS74012COMP
19 1 Tilt table PS74134COMP
20 1 Bearing PS76000
21 2 Washer PS76001
22 1 Spring PS76002
23 1 Spring PS76003
24 1 Motor

120 VAC (PS7) 2708000

24 VAC (PS7-24) PS78001

25 2 Spacer, threaded 6-32 x 2.50 round SPA1857

A1Nut, 10-32 ZH10-32NUTSH
B3Set screw, 10-32 x .3125-inch ZH10-32X.312S
C5Screw, 10-32 x .375-inch, Phillips, pan head ZH10-32X.375SPP
D1Screw, 10-32 x .5-inch, Phillips, pan head ZH10-32X.500SPP
E2Screw, 10-32 x 1-inch, Phillips, flat head ZH10-32X1.00SFP
F7Internal tooth lock washer, #10 ZH10LWSIS

G2Screw, 2-56 x .75-inch, Phillips, pan head ZH2-56X.750SRS
H2Set screw, 6-32 x .1875-inch ZH6-32X.187S

I6Screw, 6-32 x .375-inch slot, flat head ZH6-32X.375SFP
J6Screw, 6-32 x .375-inch, Phillips, pan head ZH6-32X.375SPP
L2Internal tooth lock washer, #6 (not shown) ZH6LWSIS

M Not used
N2Screw, 10-32 x .75-inch Phillips, flat head ZH10-32X.750SFP

WIRING DIAGRAMS

PS7 WIRING DIAGRAM PS7-24 WIRIN G DIAGRAM

WARRANTY AND RETURN INFORMATION

WARRANTY
Pelco will repair or replace, without charge, any merchandise proved defective in material
or workmanship for a period of one year after the date of shipment.
Exceptions to this warranty are as noted below:

• Five years on FT/FR8000 Series fiber optic products.

• Three years on Genex® Series products (multiplexers, server, and keyboard).

• Three years on Camclosure® and fixed camera models, except the CC3701H-2,
CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2, and MC3651H-2X camera
models, which have a five-year warranty.

• Two years on standard motorized or fixed focal length lenses.

• Two years on Legacy®, CM6700/CM6800/CM9700 Series matrix, and DF5/DF8 Series
fixed dome products.

• Two years on Spectra®, Esprit®, ExSite™, and PS20 scanners, including when used in
continuous motion applications.

• Two years on Esprit® and WW5700 Series window wiper (excluding wiper blades).

• Eighteen months on DX Series digital video recorders, NVR300 Series network video
recorders, and Endura™ Series distributed network-based video products.months on DX
Series digital video recorders, NVR300 Series network video recorders, Endura™ Series
distributed network-based video products, and TW3000 Series twisted pair transmission
products.

• One year (except video heads) on video cassette recorders (VCRs). Video heads will be
covered for a period of six months.

• Six months on all pan and tilts, scanners or preset lenses used in continuous motion
applications (that is, preset scan, tour and auto scan modes).

Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco
shipment. All goods requiring warranty repair shall be sent freight prepaid to Pelco, Clovis,
California. Repairs made necessary by reason of misuse, alteration, normal wear, or
accident are not covered under this warranty.

Pelco assumes no risk and shall be subject to no liability for damages or loss resulting
from the specific use or application made of the Products. Pelco’s liability for any claim,
whether based on breach of contract, negligence, infringement of any rights of any party
or product liability, relating to the Products shall not exceed the price paid by the Dealer to
Pelco for such Products. In no event will Pelco be liable for any special, incidental or
consequential damages (including loss of use, loss of profit and claims of third parties)
however caused, whether by the negligence of Pelco or otherwise.

The above warranty provides the Dealer with specific legal rights. The Dealer may also
have additional rights, which are subject to variation from state to state.

REVISION HISTORY

Manual # Date Comments

C350SM 10/99 Original version.

If a warranty repair is required, the Dealer must contact Pelco at [phone] or
[phone] to obtain a Repair Authorization number (RA), and provide the following
information:

1. Model and serial number

2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number

3. Details of the defect or problem
If there is a dispute regarding the warranty of a product which does not fall under the

warranty conditions stated above, please include a written explanation with the product
when returned.

Method of return shipment shall be the same or equal to the method by which the item
was received by Pelco.

RETURNS
In order to expedite parts returned to the factory for repair or credit, please call the factory
at [phone] or [phone] to obtain an authorization number (CA number if
returned for credit, and RA number if returned for repair).
All merchandise returned for credit may be subject to a 20% restocking and refurbishing
charge.

Goods returned for repair or credit should be clearly identified with the assigned CA or RA
number and freight should be prepaid. Ship to the appropriate address below.
If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico, send goods
to:

If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico and are
instructed to return goods to the USA, you may do one of the following:
If the goods are to be sent by a COURIER SERVICE, send the goods to:

If the goods are to be sent by a FREIGHT FORWARDER, send the goods to:

Service Department
Pelco
3500 Pelco Way
Clovis, CA 93612-5699

Pelco
3500 Pelco Way
Clovis, CA 93612-5699 USA

Pelco c/o Expeditors
473 Eccles Avenue
South San Francisco, CA 94080 USA
Phone: [phone]
Fax: [phone]

® Pelco, the Pelco logo, Spectra, Esprit, Genex, Legacy, and Camclosure are registered trademarks of Pelco.
™ Endura and ExSite are trademarks of Pelco. © Copyright 1999, Pelco. All rights reserved.