Pelco POE21U1AF Specsheet

PRODUCT SPECIFICATION

transmission and power

POE21U1AF Series High-Power, Single-Port Injector

19.6 WATT POWER OVER ETHERNET ADAPTER

Product Features

• Fully Compliant Detection, Disconnect, Overload and Voltage Control

(IEEE802.3af)

• Diagnostic LEDs

• Full Protection

– Overcurrent Protection (OCP)

– Overvoltage Protection (OVP)

• Nonvented Case

The POE21U1AF Power over Ethernet (PoE) single port power injector is designed to meet the demanding data rate and power requirements of IP cameras with high-quality streaming video capabilities. The injector offers total output power of 19.6 W, which meets the IEEE802.3af standard for detection, connection, disconnection, and fault protection.

The POE21U1AF power injector is compatible with 10/100Base-T systems and systems up to 1000 Mbps. AC input voltage ranges from 100 to 240 VAC with input frequency from 47 to 63 Hz. Maximum output load current is 350 mA at 56 VDC.

International Standards

Organization Registered Firm;

ISO 9001 Quality System

C3941 / NEW 2-15-13

TECHNICAL SPECIFICATIONS

STATUS

OUT IN

MODEL

POE21U1AF High-power, single-port PoE injector POE21U1AF-EU High-power, single-port PoE injector with

220 V, European power cord

ELECTRICAL

Input Voltage Rating 100 to 240 VAC AC Input Current 0.8 A (RMS) maximum for 120 VAC;

Leakage Current 350 AC Input Frequency 47 to 63 Hz AC Inrush Current 60 A (RMS) maximum for 240 VAC Total Output Power 19.6 W Efficiency 80% (typical) at maximum load; 120 VAC,

Hold-up Time 10 milliseconds minimum; 120 VAC and

Transient O/P Voltage Protection 60 V maximum at switch; on and off at any

Over Voltage/Current, Short Circuit Protection Outputs equipped with short circuit

Input Connectors IEC320 inlet 3-pin

0.55 A (RMS) maximum for 240 VAC

µA

60 Hz

maximum load

AC line phase

protection and overload protection according to IEEE802.3af specification; the output can be shorted permanently without damage

FRONT PANEL INDICATORS/FUNCTIONS

Status/Color Description

Solid Green Valid IEEE802.3af load detected and connected

Blinking Red/Green Invalid load connected

Blinking Red Fault; outbound power turned off due to overload

ENVIRONMENTAL

Operating Temperature 0° to 40°C (32° to 104°F) Storage Temperature –20° to 65°C (–4° to 149°F) Maximum Humidity Gradient 5% to 90%

CERTIFICATIONS

• CE, Class B

• FCC, Class B

• UL/cUL Listed

VALUES IN PARENTHESES ARE INCHES; ALL OTHERS ARE CENTIMETERS.

3.6

(1.4)

16.3 (6.4)

6.5

(2.6)

13.65 (5.37)

Pelco by Schneider Electric

3500 Pelco Way, Clovis, California 93612-5699 United States

USA & Canada Tel (800) 289-9100 Fax (800) 289-9150 International Tel +1 (559) 292-1981 Fax +1 (559) 348-1120 www.pelco.com www.pelco.com/community

Pelco, the Pelco logo, and other trad emarks associated with Pelco products referred

to in this publication are trademarks of Pelco, Inc. or its affiliates. ONVIF and the

ONVIF logo are trademarks of ONVIF Inc. All othe r product names and

Product specifications and availability are subject to change without no ti ce .

services are the property of their respective comp anies.