Pelco POE1AT-US Specsheet

PRODUCT SPECIFICATION

transmission and power

POE1AT Single-Port IEEE802.3at Midspan

GIGABIT HIGH POWER OVER ETHERNET

Product Features

• Fully 802.3at Compliant Detection, Disconnect, Over Voltage, and

Current Protection

• 30 W Output

• Full Protection

– Over Current Protection (OCP)

– Over Voltage Protection (OVP)

• Diagnostic LEDs

• Gigabit Compatibility

• Nonvented Case

The POE1AT Power over Ethernet (PoE) single-port midspan is designed to meet the demanding data rate and power requirements of IP cameras with high-quality streaming video capabilities. The PoE+ single-port midspan offers total output power of 30 W, and meets the IEEE802.3at standard for detection, connection, disconnection, and fault protection.

The POE1AT AC input voltage range is 90 to 264 VAC. Maximum input current is 0.8 A (RMS) at 120 VAC; 0.55 A (RMS) at 240 VAC.

International Standards

Organization Registered Firm;

ISO 9001 Quality System

C3961 / NEW 9-13-13

TECHNICAL SPECIFICATIONS

MODELS

POE1AT-US Single-port PoE+ midspan

with US power cord

POE1AT-EU Single-port PoE+ midspan

with European power cord

ELECTRICAL

Input

Input Voltage Rating 90 to 264 VAC AC Input Current 0.8 A (RMS) maximum at 120 VAC;

0.55 A (RMS) maximum at 240 VAC Leakage Current 350 µA maximum AC Input Frequency 47 to 63 Hz AC Inrush Current 60 A maximum at 240 VAC and maximum load

Output

Output Power 30 W Efficiency 80% (typical) at maximum load; 120 VAC,

60 Hz

Hold-Up Time 10 milliseconds minimum; 1 20 VAC, 60 Hz and

maximum load

Transient O/P Voltage Protection 60 V maximum at switch on and off at any

AC line phase

Isolation (HI-POT) Primary to Secondary:

1,500 VAC for 1 minute, 10 mA

Insulation Resistance Primary to Secondary:

>10 Mohm at 500 VDC

Over Voltage/Current, Short Circuit Protection The output is equipped with short-circuit

protection and overload protection according to the IEEE802.3at specification and conforms to UL60950-2; the output can be shorted permanently without damage

FRONT PANEL INDICATORS/FUNCTIONS

Status LED Color Description

Blinking Green Powered ON and ready for connection

Solid Green Valid IEEE802.3at load connected to OUT

Blinking Red/Green Incorrect signature; invalid load connected

Solid Red Overload indication

ENVIRONMENTAL

Operating Temperature 0° to 40°C (32° to 104°F) Storage Temperature –25° to 65°C (–13° to 149°F) Maximum Humidity Gradient 5% to 90% Immunity

ESD EN61000-4-2, Level 3 RS EN61000-4-3, Level 3 EFT/Burst EN61000-4-4, Level 2 Surge EN61000-4-5, Level 3 CS EN61000-4-6, Level 3 Voltage Dips EN61000-4-11 Harmonic EN61000-3-2 Class A

OPTIONAL ACCESSORIES

POE1XT Single-Port PoE Gigabit Extender extends PoE

100 meters (328 feet) providing a single-port

802.3af output; refer to the POE1XT specification sheet for capabilities

CERTIFICATIONS

• CE, EN55022 Class B

• FCC, Part 15, Class B

• UL/cUL Listed

Connection

AC Input Connector IEC320 inlet 3-pin (C14) Output Connection

+pins 3, 6 –pins 1, 2

Data IN/OUT Connector RJ-45

Pelco by Schneider Electric

3500 Pelco Way, Clovis, California 93612-5699 United States

USA & Canada Tel (800) 289-9100 Fax (800) 289-9150 International Tel +1 (559) 292-1981 Fax +1 (559) 348-1120 www.pelco.com www.pelco.com/community

VALUES IN PARENTHESES ARE INCHES; ALL OTHERS ARE CENTIMETERS.

0.89

(0.35)

16.3

(6.42)

0.33

(0.13)

STATUS

Pelco, the Pelco logo, and other trad emarks associated with Pelco products referred

to in this publication are trademarks of Pelco, Inc. or its affiliates. ONVIF and the

ONVIF logo are trademarks of ONVIF Inc. All othe r product names and

Product specifications and availability are subject to change without no ti ce.

services are the property of their respective comp anies.

6.5

(2.56)

OUT

3.6

(1.42)