®
Installation/Operation
PMCS14A, PMCS17A, and PMCS19A
Super-High Resolution Color Monitors
C1991M-B (2/01)
Pelco • 3500 Pelco Way, Clovis • CA 93612-5699 USA • Pelco Online @ http://www.pelco.com
In North America and Canada: Tel (800) 289-9100 or FAX (800) 289-9150 • DataFAX (800) 289-9108
International Customers: Tel +1 (559) 292-1981 or FAX +1 (559) 348-1120 • DataFAX +1 (559) 292-0435
PelcoEurope BV • Dillenburg Center, Dillenburgstraat 5F • 5652 AM Eindhoven • The Netherlands
Tel +31(40) 251-9870 • FAX +31(40) 251-9835
IMPORTANT SAFEGUARDS AND WARNINGS
1. Operate this unit only from the type of power source indicated on the label.
2. Do not block or cover ventilation openings on the back or bottom of the monitor cabinet.
3. Do not place this monitor near a radiator or heating vent.
4. Do not push objects of any kind through cabinet openings. This may result in fire or electrical shock.
5. Before adding attachments always ask a service technician to perform routine safety tests to determine that equipment is in safe operating condition. Ground potential tests should be part of the routine safety check made by the service technician.
6. Do not place monitor on an unstable cart, stand or shelf where it may fall and injure personnel or
damage equipment.
7. Route power cords so that they cannot be walked upon or tripped over. Do not allow anything to rest
on the power cord.
8. Do not install monitor in wet areas, or where it may be exposed to rain or water. Do not spill liquid of
any kind on the unit.
9. Unplug the power cord from the unit before cleaning the display. Use only a damp cloth. Do not use
alcohol, spirits, or ammonia to clean the display. DO NOT ATTEMPT TO CLEAN THE INTERIOR
OF THIS UNIT - THIS ACTION MUST BE PERFORMED BY A SERVICE TECHNICIAN AS REQUIRED DURING NORMAL MAINTENANCE.
10. Refer all servicing to qualified service personnel. REMOVAL OF BACK COVER BY UNAUTHORIZED PERSONNEL MAY EXPOSE THE USER TO DANGEROUS VOLTAGES OR OTHER HAZARDS.
11. Unplug the unit immediately and notify a service technician:
a. If liquid has been spilled into the display or the display has been exposed to rain or water.
b. If the unit has been dropped or the cabinet damaged.
c. If fuses continue to blow.
d. If the power cord is damaged or frayed.
e. If a distinct change from normal operation is apparent.
When replacement parts are required, be sure that the service technician uses components specified by
the manufacturer. UNAUTHORIZED SUBSTITUTIONS MAY RESULT IN FIRE, ELECTRICAL SHOCK
OR OTHER HAZARDS.
Upon completion of any service or repairs, ask a technician to perform safety checks to determine that
the equipment is in safe operating condition.
WARNING SERIOUS SHOCK HAZARDS EXIST WITHIN THE COVER OF THIS MONITOR.
DO NOT OPEN THE COVER UNDER ANY CIRCUMSTANCES. THERE ARE NO USER SERVICEABLE COMPONENTS INSIDE.
[ 2 ] Pelco Manual C1991M-B (2/01)
DESCRIPTION
The PMCS14A, PMCS17A, and PMCS19A are super-high resolution color monitors. All monitors have
computer-grade picture tubes.The PMCS14A and PMCS17A produce horizontal resolution of 700 TV
lines and PMCS19A produces 800 TV lines. Standard high-resolution monitors produce only about 350
TV lines.
The monitors automatically detect the power supply input (90-260 VAC, 50/60 Hz).
Models
PMCS14A Super-high resolution color monitor, 14-inch (35.56 cm) diagonal picture display
PMCS17A Super-high resolution color monitor, 17-inch (43.18 cm) diagonal picture display
PMCS19A Super-high resolution color monitor, 19-inch (48.26 cm) diagonal picture display
Pelco Manual C1991M-B (2/01) [ 3 ]
INSTALLATION
The monitor may be placed on any flat surface (desk or table) or rack-mounted. To rack-mount the
monitor follow the instructions supplied with the rack-mount kit.
Video and Power Connections
1. Video Cable Connection (Refer to Table A for video coaxial cable requirements.)
a. Connect the video cable to the BNC video input labeled V1 IN on the back panel of the monitor.
If the installation requires a second video input, connect a video cable to the BNC video input labeled V2 IN.
b. Looping Operation Only - Connect a video cable to the BNC connector labeled V1 OUT. If the in-
stallation requires a second video output, connect a video cable to the BNC video output labeled
V2 OUT. Refer to Figures 2 and 3.
2. Impedance Switch Setting
a. Terminating Operation Only - Set the termination switch to 75Ω position.
b. Looping Operation Only - Set the impedance switch to the V1-HI and V2-HI positions. Refer to
Figures 2 and 3.
3. Plug the power cord (provided) into the AC INLET connection on the back panel. Plug the other end
of the cord into a power receptacle.
FRONT
VOLUME SHARP BRIGHT CONT. COLOR TINT
BACK
V1-HI
75
V1 IN AU1 IN
V1 OUT
V2 IN
V2 OUT
AU1 OUT
V2-HI
75
AC INLET
AU1 AU2
VIDEO 1 VIDEO 2 S-VIDEO
AU2 IN
Y/C-HI
75
AU2 OUT
S-VIDEO IN
S-VIDEO OUT
Figure 1. Model PMCS14A, PMCS17A, and PMCS19A Color Monitors, Front and Back Panels
[ 4 ] Pelco Manual C1991M-B (2/01)
Table A. Video Coaxial Cable Requirements
Cable Type* Maximum Distance
RG59/U 750 ft (229 m)
RG6/U 1,000 ft (305 m)
RG11/U 1,500 ft (457 m)
* Minimum cable requirements:
75 ohms impedance
All-copper center conductor
All-copper braided shield with 95% braid coverage
V1-H
CAMERA CAMERA
V1-L
V1 IN AU1 IN
V2-H
V2-L
V1 OUT
V2 OUT
V2 IN
AU1 OUT
AU2 IN
AU2 OUT
S-VHS IN
S-HI
S-LO
S-VHS OUT
VCR VCR
Figure 2. Looping Operation - One Monitor with External Video Equipment
V1-H
V1-L
V1 IN AU1 IN
V2-H
V2-L
V1 OUT
V2 OUT
CAMERA
AU2 IN
V2 IN
AU1 OUT
AU2 OUT
S-HI
S-LO
S-VHS IN
S-VHS OUT
V1-H
V1-L
V1 IN AU1 IN
V2-H
V2-L
V1 OUT
V2 OUT
V1-H
V1-L
V2 IN
AU1 OUT
AU2 OUT
S-HI
S-LO
S-VHS OUT
S-VHS IN
AU2 IN
V1 IN AU1 IN
V2-H
V2-L
V1 OUT
V2 OUT
AU2 IN
V2 IN
AU1 OUT
AU2 OUT
VCR
Figure 3. Looping Operation - Maximum of Three Monitors with External Video Equipment
Pelco Manual C1991M-B (2/01) [ 5 ]
S-VHS IN
S-HI
S-LO
S-VHS OUT
OPERATION
1. Set the video format switch located on the front panel to one of the following settings:
VIDEO1 - Composite video (NTSC/PAL) mode
VIDEO2 - Composite video (NTSC/PAL) mode for two, video input operation
S-VIDEO - S-VHS mode if the S-VHS input jack on the back of the monitor is used
2. If required adjust the picture using the control knobs on the front panel.
Front Panel Adjustments
TINT Color phase adjustment. Turn clockwise to increase the greenish tones in the picture.
Turn counterclockwise to increase the reddish tones in the picture.
COLOR Color saturation level. Turn the control knob clockwise to increase the saturation level
CONT Contrast adjustment. Proper adjustment will allow maximum gradations between the
BRIGHT Brightness display adjustment. Turn the control clockwise to increase brightness and
SHARP Sharpness adjustment. Adjust control knob to obtain the clearest picture.
VOLUME Audio adjustment. Turn the control clockwise to increase volume and counterclockwise
and counterclockwise to decrease the saturation level.
darkest and lightest picture contrast. Turn the control clockwise to increase picture contrast and counterclockwise to decrease contrast.
counterclockwise to decrease brightness.
to decrease volume.
[ 6 ] Pelco Manual C1991M-B (2/01)
MAINTENANCE
If the quality of the picture is poor and cannot be improved by making adjustments on the front control
panel, inspect all system connections and cable runs.
To reduce the risk of electrical shock, do not remove the cover or back of monitor. No user-serviceable
parts are inside. Refer servicing to qualified personnel, or contact the Pelco Customer Service Department for assistance. Refer to the Warranty and Return Information section.
SPECIFICATIONS
ELECTRICAL
Input Voltage 90-260 VAC, 50/60 Hz, automatic switching
Power Consumption
PMCS14A 60 watts
PMCS17A 95 watts
PMCS19A Approx. 100 Watts
Horizontal Resolution
PMCS14A 700 TV lines
PMCS17A 700 TV lines
PMCS19A 800 TV lines
Visual Picture Size
PMCS14A 13-inch diagonal
PMCS17A 16-inch diagonal
PMCS19A 18-inch diagonal
Sweep Linearity 10%
Speaker Output 1.0 watt (-3 dBV)
GENERAL
Input/Output
Video 2 BNC inputs, 75 ohms, or Hi-Z
Audio 2 RCA inputs, Hi-Z
S-Video 1 input DIN
Construction Steel cabinet
Finish Black with black bezel around screen
Dimensions
PMCS14A 14.0 (W) x 12.9 (H) x 15.0 (D) inches
PMCS17A 16.0 (W) x 14.5 (H) x 16.0 (D) inches
PMCS19A 17.4 (W) x 16.4 (H) x 17.5 (D) inches
Weight
PMCS14A 29 lb (13.0 kg)
PMCS17A 41 lb (18.5 kg)
PMCS19A 50 lb (22.5 kg)
2 looping through outputs
2 looping through outputs
1 looping output
(35.6 x 32.7 x 38.1 cm)
(40.6 x 36.9 x 40.6 cm)
(44.0 x 41.5 x 44.5 cm)
ENVIRONMENTAL
Operating Temperature 32° to 106°F (0° to 41°C)
Humidity 0% to 90% (non-condensing)
(Design and product specifications subject to change without notice.)
Pelco Manual C1991M-B (2/01) [ 7 ]
REGULATORY NOTICES
This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant
to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that the interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try and correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Any changes or modifications not expressly approved by the party responsible for compliance could
void the user ’s authority to operate the equipment.
WARRANTY AND RETURN INFORMATION
WARRANTY
Pelco will repair or replace, without charge, any merchandise proved
defective in material or workmanship for a period of one year after
the date of shipment. Exceptions to this warranty are as noted below:
• Three years on Genex® Series (multiplexers, server, and keyboard).
• Two years on cameras and all standard motorized or fixed focal
length lenses.
• Two years on Legacy®, Camclosure™ Camera Systems,
CM6700/CM8500/CM9500/CM9750/CM9760 Matrix,
PelcoVision®, DF5 Series and DF8 Fixed Dome products.
• Two years on Spectra® and Esprit™, including when used in
continuous motion applications.
• Two years on WW5700 series window wiper (excluding wiper
blades).
• Six months on all pan and tilts, scanners or preset lenses used
in continuous motion applications (that is, preset scan, tour and
auto scan modes).
Pelco will warrant all replacement parts and repairs for 90 days
from the date of Pelco shipment. All goods requiring warranty repair shall be sent freight prepaid to Pelco, Clovis, California. Repairs made necessary by reason of misuse, alteration, normal wear,
or accident are not covered under this warranty.
Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from the specific use or application made of
the Products. Pelco’s liability for any claim, whether based on breach
of contract, negligence, infringement of any rights of any party or
product liability, relating to the Products shall not exceed the price
paid by the Dealer to Pelco for such Products. In no event will Pelco
be liable for any special, incidental or consequential damages (including loss of use, loss of profit and claims of third parties) however
caused, whether by the negligence of Pelco or otherwise.
® Pelco, the Pelco logo, Spectra, Genex, Legacy, and PelcoVision are registered trademarks of Pelco.
™ Esprit and Camclosure are trademarks of Pelco.
© Copyright 2001, Pelco. All rights reserved.
The above warranty provides the Dealer with specific legal rights.
The Dealer may also have additional rights, which are subject to
variation from state to state.
If a warranty repair is required, the Dealer must contact Pelco at
(800) 289-9100 or (559) 292-1981 to obtain a Repair Authorization
number (RA), and provide the following information:
1. Model and serial number
2. Date of shipment, P.O. number, Sales Order number, or Pelco
invoice number
3. Details of the defect or problem
If there is a dispute regarding the warranty of a product which does
not fall under the warranty conditions stated above, please include
a written explanation with the product when returned.
Method of return shipment shall be the same or equal to the method
by which the item was received by Pelco.
RETURNS
In order to expedite parts returned to the factory for repair or credit,
please call the factory at (800) 289-9100 or (559) 292-1981 to obtain an authorization number (CA number if returned for credit, and
RA number if returned for repair). Goods returned for repair or credit
should be clearly identified with the assigned CA/RA number and
freight should be prepaid. All merchandise returned for credit may
be subject to a 20% restocking and refurbishing charge.
Ship freight prepaid to: Pelco
3500 Pelco Way
Clovis, CA 93612-5699
REVISION HISTORY
Manual # Date Comments
C1991M 11/00 Original version.
C1991M-A 01/01 Added ETL and cETL certifications.
C1991M-B 2/01 Added information on model PMCS19A.
® Pelco, the Pelco logo, Spectra, Genex, Legacy, and PelcoVision are registered trademarks of Pelco.
Loading...