Pelco PMCL-WMT installation manual

INSTALLATION

PMCL-WMT Monitor Mount

C2224M-C (10/14)

Important Safety Instructions

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Installation should be done only by qualified personnel and conform to all local codes.

6. Only use installation methods and materials capable of supporting four times the maximum specified load.

7. Only use replacement parts recommended by Pelco.

8. This unit is designed for indoor use only, and it must not be installed where exposed to rain or moisture.

Description

The PMCL-WMT is a tilt/swivel wall mount that can be used to mount any of Pelco’s 300, or 400 Series flat panel LCD monitors. This mount supports Pelco
500 Series PMCL524BL and PMCL532BLLCD monitors, although a PMCL-V200 adapter plate is required. This mount can be swiveled 360 degrees to allow
you to use the monitor in either landscape or portrait view. The mount also allows you to tilt the monitor 35 degrees for the best viewing angle.
The PMCL-WMT is capable of supporting a maximum load of 40.8 kg (90 lbs).

PARTS LIST

The following parts are supplied:

Qty Description

1 Wall bracket
1 Monitor mount
4 M4 x 10 mm pan head Phillips screws, stainless steel
4 Split lock washers
4 M6 x 12 mm pan head Phillips screws, stainless steel
4 Flat washers
1 10-32 socket head screw
1 Flat washer, #10, stainless steel
1 Allen wrench, 3/16 in.
1 Allen wrench, 5/32 in.

USER-SUPPLIED PARTS LIST

Parts for attaching the wall bracket to the wall are required but not supplied. Lag bolts, toggle bolts, or anchor bolts are required as specified on the
following page for attaching the wall bracket to the wall. The type of parts the user is required to supply is dependent on the type of wall to which the
bracket is installed.

Installation

To install the tilt/swivel wall mount:

1. Disassemble the monitor mount from the wall bracket by removing the 10/32-inch socket
head screw and flat washer from the underside of the mount. Use the 5/32-inch Allen
wrench (supplied) to loosen the screw. Slide the two pieces apart and retain the washer
and screw for reassembly.

2. Attach the monitor mount to the monitor. Refer to Figure 1 and do one of the following:

• 31-inch Monitor or Smaller: Align the monitor to the correct hole

pattern on the mounting plate. Use the M4 x 10 mm screws and split
lock washers (supplied) to secure the monitor to the mounting plate.

or

• Monitors Larger than 31-inches: Align the monitor to the outside

hole pattern of the monitor plate. Use the M6 x 12 mm screws and
flat washers (supplied) to secure the monitor to the mounting plate.

3. Attach the wall bracket to the wall with the short side pointing down.
Mounting hardware is not supplied.

Figure 1. Attaching the Monitor Mount

Installing the mount to a wood stud wall

WARNING:

• The wood stud must be at least 2-inch x 4-inch.

• The studs must be covered with a maximum 1/2-inch thick layer of wallboard or plywood.

1. Use a stud finder to locate and mark the edges of the wood stud in which the mount will be attached.

2. Center two of the wall bracket mounting holes vertically between the edges of the wood stud. Use the wall bracket as a template to mark the two
mounting hole locations.

3. At the two marked mounting hole locations, drill 11/64-inch diameter holes 2-inches deep from the wall surface into the wood stud.

4. Attach the wall bracket to the wall securing it to the wood stud using two 1/4-inch diameter x 2-inch lag bolts as shown in Figure 2 and Figure 3.

5. If mounting on a wallboard surface, secure the remaining two wall bracket mounting holes by drilling 11/16-inch diameter holes through the remaining
two wall bracket mounting holes through the wallboard. Attach using the recommended spring wing toggle bolt specified in the following table for
recommended hardware and supplier.

6. If mounting on a plywood surface, secure the bracket by inserting a lag bolt through each wall bracket mounting hole and through the plywood. Refer
to the following table for recommended hardware and supplier.

Mounting Surface Hardware Supplier

Minimum 2-inch x 4-inch wood stud with
maximum 1/2-inch thick wallboard

Minimum 2-inch x 4-inch wood stud with
maximum 1/2-inch thick plywood

Two toggle bolts, 1/4-inch diameter x 2-inch
requires 11/16-inch diameter holes through wall

Two lag bolts, 1/4-inch diameter x 2-inch Any hardware supplier

Simpson Toggle Bolt, Strong-Tie Spring Wing
Simpson part number: SWTB25300M

2 C2224M-C (10/14)

INSTALLING THE MOUNT TO A SOLID CONCRETE OR CINDER BLOCK WALL

WARNING:

• Do not install hardware into mortar joints in filled or non-filled cinder block walls.

• Concrete must be a minimum of 3600 psi or 25 Mpa density.

• Concrete must be minimum 3-inch thickness or concrete filled cinder block.

1. Level and use the wall bracket as a template to mark the mounting hole locations on the wall.

2. At the marked mounting hole locations, drill 1/4-inch diameter holes 1.75-inches deep.

Use two toggle bolts on wallboard

WOOD STUD

TOGGLE BOLT

WOOD STUD

PLYWOOD

LAG BOLT

Figure 2. Attaching the Wall Bracket to

Wood Stud and Plywood

LAG BOLT

Figure 3. Attaching the Wall Bracket to

Wall Board and Wood Stud

WALLBOARD

3. Attach the wall bracket to the wall using 1/4-inch diameter x 2-inch wedge anchors as shown in Figure 4. The recommended anchor for this hole
diameter is ITW Red Head Trubolt Wedge Anchor SWW-1422.

SOLID

CONCRETE

WALL

NUT

WEDGE

ANCHOR

CINDER BLOCK

WALL

Figure 4. Attaching the Wall Bracket to Solid Concrete or Cinder Block Wall

4. Carefully slide the monitor mount into the slots of the wall bracket. Use the 10-32 socket head screw and the flat washer (supplied) to fasten the wall
bracket to the monitor mount. Refer to Figure 5. Use the 5/32-inch Allen wrench (supplied) to tighten the screw.

5. Using the 3/16-inch Allen wrench (supplied), loosen the button head bolts on the side of the mounting head. Tilt the monitor to the desired angle.
To secure the monitor in place, retighten the button head bolts. Refer to Figure 6.

3 C2224M-C (10/14)

6. To swivel the monitor between portrait and landscape views, loosen the nut on the back side of the mounting head using a 9/16-inch wrench (not
supplied). Retighten the nut to secure the monitor in place.

Figure 5. Attaching the Wall Mount

and Monitor

Figure 6. Securing the Monitor

WARRANTY

For information about Pelco’s product warranty and thereto related information, refer to www.pelco.com/warranty.

REVISION HISTORY

Manual # Date Comments

C2224M 8/06 Original version.
C2224M-A 11/06 Inserted statement per UL about minimum2x4wood stud.
C2224M-B 12/06 Added hardware information for large monitors per ECO 06-17078.
C2224M-C 10/14 Added mounting details for UL compliance and updated template.

Pelco, the Pelco logo, and other trademarks associated with Pelco products referred to in this publication are trademarks of Pelco, Inc. or its affiliates. © Copyright 2014,Pelco, Inc.
ONVIF and the ONVIF logo are trademarks of ONVIF Inc. All other product names and services are the property of their respective companies. All rights reserved.
Product specifications and availability are subject to change without notice.

Pelco, Inc. 625 W. Alluvial Ave., Fresno, CA 93711 United States

USA & Canada Tel [phone] Fax [phone]

International Tel [phone] Fax [phone]

www.pelco.com