7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one blade wider than the
other. A grounding plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the
provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the points where they exit from
the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Only use with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use
caution when moving the cart/apparatus combination to avoid injury from tip-over.
13. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power
supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or
moisture, does not operate normally, or has been dropped.
14. Unplug the apparatus during lightning storms or when unused for long periods of time.
15. Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases shall be placed on the apparatus.
16. WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.
17. Installation should be done only by qualified personnel and conform to all local codes.
18. Unless this unit is specifically marked as NEMA Type 3, 3R, 3S, 4, 4X, 6, or 6P enclosure, it is designed for indoor use only and it must not
be installed where exposed to rain and moisture.
19. Only use installation methods and materials capable of supporting four times the maximum specified load.
20. Only use replacement parts recommended by Pelco.
21. Avoid touching the screen directly with your fingers as the oils from your skin may be difficult to remove from the LCD.
22. Do not apply direct pressure on the screen.
23. Keep the monitor in a dust-free environment and away from strong electromagnetic fields.
24. Do not use attachments, such as mounts, that are not recommended by Pelco. They may be hazardous.
25. Do not place the monitor on an unstable stand, bracket, or mount. The unit may fall, causing serious damage to the unit or injury to a
person. Only use mounts recommended by Pelco.
26. A CCC-approved power cord must be used to power this equipment when used in China.
27. A still image displayed too long may cause permanent damage to the LCD panel. Watching the LCD in 4:3 format for a long time may leave
traces of borders displayed on the left, right and center of the screen caused by the difference of light emission on the screen. Using a
camera or a system may cause a similar effect to the screen. Damages caused by this effect are not covered by the warranty.
The product and/or manual may bear the following marks:
C2967M-C (8/11)5
This symbol indicates that dangerous voltage constituting a risk of electric shock is present
within this unit.
This symbol indicates that there are important operating and maintenance instructions in
the literature accompanying this unit.
Important Notices
REGULATORY NOTICES
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
RADIO AND TELEVISION INTERFERENCE
This equipment has been tested and found to comply with the limits of a Class A digital device, pursuant to Part 15 of the FCC rules. These limits
are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual,
may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference
in which case the user will be required to correct the interference at his own expense.
Changes and Modifications not expressly approved by the manufacturer or registrant of this equipment can void your authority to operate this
equipment under Federal Communications Commission’s rules.
In order to maintain compliance with FCC regulations shielded cables must be used with this equipment. Operation with non-approved
equipment or unshielded cables is likely to result in interference to radio and television reception.
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.
6C2967M-C (8/11)
Description
Pelco’s PMCL500 Series small, full high-definition (FHD) monitors deliver 1920 x 1080 native resolution with high performance and the truest
color reproduction available. These 24- and 32-inch displays combine the latest technologies into a perfect compliment to your investment in
megapixel imaging and performance. These monitors are specifically engineered to exceed the demands of surveillance operators.
NOTE: When the PC goes into sleep mode, the monitor turns off. Activating the PC (either by moving the mouse, hitting a keyboard key, or
pressing the power button) does not activate the monitor. You must press the power button for the video to resume.
MODELS
PMCL524FL24-inch LCD monitor (610 mm)
PMCL532F32-inch LCD monitor (813 mm)
RECOMMENDED MOUNTS
The PMCL-V200 adapter plate is required when mounting a PMCL532F monitor using any of the following equipment.
PMCL-WMWall mount
PMCL-WMTTilt/swivel wall mount
PMCL-CMCeiling mount
PMCL-CMPCeiling mount with pole
PMCL-WM1ATilt/swivel single-arm wall mount
C2967M-C (8/11)7
PACKAGE CONTENTS
Figure 1. Package Contents
ì
24- or 32-inch FHD Monitor (1 ea.)
î
Power Adapter (1 ea.)
ï
USA Standard Power Cord (1 ea.)
ñ
European Standard Power Cord (1 ea.)
ó
DVI Cable (1 ea.)
r
VGA Cable with 15-Pin D-Sub Connection (1 ea.)
NOTE: Consider keeping the box and packaging in storage for use in the future when you may need to transport the monitor. The fitted foam
packing is ideal for protecting the monitor during transport.
8C2967M-C (8/11)
s
(PMCL532F only) Saddle for Power Adapter (1 ea.)
t
(PMCL532F only) Saddle Screws (2 ea.)
u
(PMCL532F only) Remote Control (1 ea.)
~í
(PMCL532F only) AAA Batteries (2 ea.)
~â
Quick Start Guide (1 ea.)
~ä
Operation Manual Resource Disc (1 ea.)
Installation
STAND SCREWS
STAND SCREWS
REMOVING THE STAND FOR WALL MOUNTING
1. Turn off the monitor and the power before disconnecting the power cable.
2. Turn off the computer before disconnecting the monitor signal cable.
3. Clear an open area on a flat workspace, such as your desk.
4. To protect the monitor and screen, place a soft towel between the screen and the desk to create a padded surface.
5. Lay the screen face down on the towel and unscrew the four screws that attach the stand to the monitor (refer to Figure 2 or Figure 3,
depending on model).
PMCL524FL
Figure 2. Unscrewing the Stand Screws (PMCL524FL)
PMCL532F
Figure 3. Unscrewing the Stand Screws (PMCL532F)
C2967M-C (8/11)9
Loading...
+ 19 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.