Pelco MR5000 User Manual

®

Installation/Operation

ICS-DO101ABK
Integrated Camera System for
the MR5000 Series Public View System

C2436M-B (9/02)

Pelco

• 3500 Pelco Way • Clovis, CA 93612-5699 USA •

In North America and Canada:

International Customers:

Tel [phone] • FAX [phone]

Tel [phone] • FAX [phone]

 '

www.pelco.com

[ 2 ] Pelco Manual C2436M-B (9/02)

TABLE OF CONTENTS

IMPORTANT SAFEGUARDS AND WARNINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

ADJUSTMENTS (COLOR CAMERA ONLY) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

VERTICAL PHASE (24 VAC OPERATION ONLY) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

AUTO IRIS LEVEL ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

FOCUS ADJUSTMENT FOR FIXED FOCAL LENGTH LENS WITH AUTO IRIS . . . . . . . . . . . . . . 9

SWITCH SETTINGS FOR FIXED FOCAL LENGTH LENS WITH AUTO IRIS . . . . . . . . . . . . . . . . 9

SWITCH SETTINGS FOR FIXED FOCAL LENGTH LENS WITHOUT AUTO IRIS . . . . . . . . . . . 10

SWITCH SETTINGS FOR VARIFOCAL LENS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

REGULATORY NOTICES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

WARRANTY AND RETURN INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Pelco Manual C2436M-B (9/02) [ 3 ]

[ 4 ] Pelco Manual C2436M-B (9/02)

IMPORTANT SAFEGUARDS AND WARNINGS

1. Installation and servicing should only be done by qualified service personnel and conform to all local
codes.

2. Unless the unit is specifically marked as a NEMA Type 3, 3R, 3S, 4, 4X, 6 or 6P enclosure, it is
designed for indoor use only and must not be installed where exposed to rain and moisture.

3. Use only installation methods and materials capable of supporting four times the maximum specified
load.

DESCRIPTION

Designed specifically for the MR5000 Series Public View System, the ICS-DO101ABK Integrated Camera
System packages a camera and lens into a small, discreet, high-security dome.

Pelco’s MR5000 Public Viewing Station is specifically designed for retail applications to provide a clear,
visual warning to potential shoplifters that these premises are under surveillance. When properly installed
the station is an effective deterrent against shoplifting.

INSTALLATION

IMPORTANT

To maximize
tamper
resistance
when not
using the
side conduit
opening for wire
connections, verify that the
conduit plug and set screw are tight.

1

Attach Adapter Plate to Base of ICS-DO101ABK

1. Align the adapter plate to the base of the ICS-DO101ABK.

2. Using the two 10-32 x .375-inch pan head screws and internal lock washers, attach the base of
the ICS-DO101ABK to the adapter plate.

Pelco Manual C2436M-B (9/02) [ 5 ]

2 Prepare Video and Electrical Cabling

1. Temporarily remove the bottom end cap of
the MR5000 Series mount if it is installed.

2. Feed the 42-inch video cable (provided)
through the monitor feedthrough hole in the
mount arm and out the bottom end of the
mount arm.

3. Pull power wires through the ICS-DO101ABK
feedthrough located at the bottom of the
mount arm. Remove the .50-inch plug
if it is installed.

4. Pull wires through the adapter plate of the
ICS-DO101ABK and into the base of the
ICS-DO101ABK.

5. Use the supplied 3/16-inch Allen wrench and slightly loosen

5/16-18 x .75-inch Allen pan head screws that secure the MR5000M mount base to the mount arm.

6. Feed the video cable attached to the ICS-DO101ABK back box through the ICS-DO101ABK
feedthrough in the mount arm and out the bottom end of the mount arm.

7. Hook the adapter plate over the loosened screws. Tighten the screws to secure the adapter plate
to the mount.

(do not remove)

the two

3 Connect Video and Power

1. Connect the video cable. Place the cable inside the MR5000 Series mount arm and install the
bottom end cap of the mount to conceal the cable.

2. Depending on the input voltage, connect either the 12 VDC or 24 VAC input power wires to
the appropriate positions on the terminal block inside the base.

3.

12 VDC Operation Only –

The camera is set for 24 VAC operation at the factory. For 12 VDC operation remove the jumper
from the 24 VAC position and install it on the 12 VDC position.

[ 6 ] Pelco Manual C2436M-B (9/02)

CAUTION

Heater elements could be hot! When camera power is on, use caution when
adjusting the camera. This applies to all models.

4 Install Camera

1. Some indoor installations do not require a

heater. If the installation does not require a
heater, remove the heater board from the cam­era assembly. To remove the heater apply
pressure and press on the corner of the
board.

2. If the heater is installed, plug the heater con­nector from the camera into the mating con­nector inside the base. Plug the video con­nector from the camera into the mating
connector inside the base.

Turn on power to the camera and monitor.

3. If you have a varifocal lens, hold the assem­bly in your hand and point the lens toward
what you want to view. Loosen the focal
length and focus locking screws. Adjust ac­cording to scene detail. Retighten the screws.

4. Always make sure the tab on the camera
bracket is pointing out of the enclosure (away
from the mount). Gently squeeze the bracket,
place it against the shoulder inside the base,
and gently release.

Proper camera orientation: The camera
bracket tab points out of the enclosure and
the top of the camera is pointed in the oppo­site direction.

Pelco Manual C2436M-B (9/02) [ 7 ]

5 Install Dome and

Trim Ring

1. Align the screw holes in the trim ring with
those in the camclosure base.

2. Domes with Liners (only) –
Position the viewing window over the lens of the camera.
a. Loosen the three Phillip screws located in the dome.
b. Insert the blade of a standard screwdriver in one of the

adjustment grooves. Move dome into position.

c. Tighten the three Phillip screws to lock liner in place.

3. Tighten the tamper-resistant screws with the supplied 1/8-inch hollow screwdriver bit.

ADJUSTMENT
GROOVE

DOME LINER

LOOSEN SCREWS

ADJUSTMENTS (COLOR CAMERA ONLY)

If you have a color camera, it is set up at the factory and normally requires no adjustments. Sometimes,
however, adjustments may be necessary.

1. Remove the dome and trim ring using the supplied 1/8-inch hollow screwdriver bit.

2. Adjust the vertical phase, iris level, focus, or switch settings
(refer to procedures below).

3. Replace the dome and trim ring.

Ver tical Phase
(24 VAC Operation Only)

Adjustment is required if there is vertical roll when switching
between two cameras.

1. Reverse the 24 VAC connections on one camera. If both
cameras are connected to the same transformer, this should
solve the problem.

2. If reversing the connections does not solve the problem, or if
cameras are connected to different transformers, turn the adjust­ment screw on one camera (while switching as rapidly as possible
between the two camera views) until the switching is clean and
there is no vertical roll. If more than two cameras are out of syn-

Auto Iris Level Adjustment

If you have a varifocal lens or fixed focal length lens
with an auto iris, you can adjust the level setting to
increase or decrease brightness.

[ 8 ] Pelco Manual C2436M-B (9/02)

Focus Adjustment for Fixed Focal Length Lens
with Auto Iris

CAUTION

Heater elements could be hot! When camera power is on, use caution when
adjusting the camera.

To adjust the focus, it may be necessary to remove the heater board in order to loosen the locking screw
on the bottom of the lens.

To remove the heater board:

1. Disconnect the four-pin heater wiring.

2. Wait for the heater elements to cool if they are hot.

3. Apply pressure and press on the corner of the board.

To adjust the focus:

FOCUS
ADJUSTMENT
SCREW

1. Loosen the locking screw on the bottom of the lens.

2. Move the screw in the slot to bring the picture into focus.

3. Retighten the locking screw.

4. Replace the heater board if it was removed.

5. Reconnect the four-pin heater wiring.

ADJUSTMENT
SLOT

BOTTOM VIEW OF CAMERA WITH
HEATER BOARD REMOVED

Switch Settings for Fixed Focal Length Lens
with Auto Iris

Refer to the switch drawing. The switch is located next to the lens. Automatic backlight compensation
(factory setting) is used under varying lighting conditions (such as outdoors) or fixed lighting conditions
where there are no bright spots that darken other picture details. Manual backlight compensation is used
in fixed lighting conditions to optimize the picture detail when there are bright spots.

ALC/ELC switch: Always ALC

Y/DC switch: Always DC

Auto backlight compensation: BLC switch OFF

ABL switch ON

Manual backlight compensation: BLC switch ON

ABL switch OFF

FACTORY SETTINGS

ALCYBLC

ON

OFF

DC

ELC

= SWITCH POSITION

OFF

ABL

OFF

Pelco Manual C2436M-B (9/02) [ 9 ]

Switch Settings for Fixed Focal Length Lens
Without Auto Iris

Refer to the switch drawing. The switch is located next to the lens. Automatic backlight compensation
(factory setting) is used under varying lighting conditions (such as outdoors) or fixed lighting conditions
where there are no bright spots that darken other picture details. Manual backlight compensation is used
in fixed lighting conditions to optimize the picture detail when there are bright spots.

ALC/ELC switch: Always ELC

Y/DC switch: Not used

Auto backlight compensation: BLC switch OFF

ABL switch ON

Manual backlight compensation: BLC switch ON

ABL switch OFF

FACTORY SETTINGS

ALCYBLC

ON

OFF

NOT USED

DC

ELC

= SWITCH POSITION

OFF

ABL

OFF

Switch Settings for Varifocal Lens

The high resolution camera with
varifocal lens and auto iris is
configured at the factory for
optimal performance in lighting
conditions where auto iris is
required. It is also configured with
the shutter speed set at 1/60
(NTSC) or 1/50 (PAL) and AGC

1AWB Automatic white balance
2 GAM Gamma function
3AGC Automatic gain control
4 ESC Electronic shutter control
5 BLC Backlight compensation
6FL Flickerless
7AE Automatic exposure
8 Not used

AE Functions

set at 6 dB of gain.

To enable automatic exposure

Turn on switch 7, and then turn on/off switch 4 for
electronic shutter control, switch 5 for backlight
compensation, and switch 6 for flickerless
motion.

To manually set and lock AWB

Place a white background in front of camera and
turn off switch 1.

For gamma correction

Switch to accurately reproduce scene brightness;
when turned on, y = 0.6, and when turned off,
y = 1.0.

For gain control

Switch 3 On increases gain by 6 dB, and switch 3
Off increases gain by 18 dB.

FACTORY SETTINGS

12345678

OFF

= SWITCH POSITION

To enable auto iris and manually set
shutter speed

Turn off switch 7; set switches 4, 5, and 6 for the
desired shutter speed.

CAUTION

Do not change the shutter speed
unless you understand how changing the settings
will affect the scene detail.

Shutter Switch Number and Position

Speed 7 6 5 4

1/60 (NTSC)
1/50 (PAL)
1/100 Off On On
1/250 On Off On
1/500 Off Off On
1/1000 On On Off
1/2000 Off On Off
1/4000 On Off Off
1/10000 Off Off Off

On On On

Off

[ 10 ] Pelco Manual C2436M-B (9/02)

SPECIFICATIONS

Electrical

Input Voltage: 12 VDC or 24 VAC, ±10%
Power
Consumption: 13 watts or less
Video
Connector: BNC
Operating
Te mperature: -50° to 122°F (-46° to 50°C)

De-ices to -10°F (-23°C)

General

Cable Entry: 3/4-inch (1.91 cm) conduit fitting

and 3/4-inch (1.91 cm) opening

for NPT threaded pipe
Pan/Tilt
Adjustment: Manual; 360° pan; 180° tilt

(Design and product specifications subject to change without notice.)

Ratings: NEMA 4, IP 66 when installed

properly
CE
UL/cUL

Construction: Aluminum with steel camera

mounting bracket and polycar-

bonate dome
Finish: Gray polyester powder coat
Dimensions

Base: 3.70 (H) x 5.30 (W) inches

(9.40 x 13.50 cm)

Bubble: 3.75-inch diameter

Environment: Low temperature,

indoor/outdoor
Unit Weight: 2.20 lb (1.00 kg)

Regulatory Notices

FCC Class A (monochrome, EIA cameras only)

This equipment has been tested and found to comply with the limits of a Class A digital device, pursuant
to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with the in­struction manual, may cause harmful interference to radio communications. Operation of this equipment
in a residential area is likely to cause harmful interference in which case the user will be required to cor­rect the interference at his own expense.

FCC Class B (color, NTSC cameras only–except varifocal)

This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant
to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However there is no guarantee that the interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try and correct the interfer­ence by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.

• Consult the dealer or an experienced radio/TV technician for help.

Pelco Manual C2436M-B (9/02) [ 11 ]

PRODUCT WARRANTY AND RETURN INFORMATION

WARRANTY

Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of
shipment.

Exceptions to this warranty are as noted below:

• Five years on FT/FR8000 Series fiber optic products.

• Three years on Genex

• Three years on Camclosure
MC3651H-2X camera models, which have a five-year warranty.

•Two years on standard motorized or fixed focal length lenses.

•Two years on Legacy

•Two years on Spectra

•Two years on Esprit

• Eighteen months on DX Series digital video recorders, NVR300 Series network video recorders, and Endura
products.

• One year (except video heads) on video cassette recorders (VCRs). Video heads will be covered for a period of six months.

• Six months on all pan and tilts, scanners or preset lenses used in continuous motion applications (that is, preset scan, tour and auto scan modes).

Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco shipment. All goods requiring warranty repair shall be sent freight
prepaid to Pelco, Clovis, California. Repairs made necessary by reason of misuse, alteration, normal wear, or accident are not covered under this
warranty.

Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from the specific use or application made of the Products. Pelco’s
liability for any claim, whether based on breach of contract, negligence, infringement of any rights of any party or product liability, relating to the Products
shall not exceed the price paid by the Dealer to Pelco for such Products. In no event will Pelco be liable for any special, incidental or consequential
damages (including loss of use, loss of profit and claims of third parties) however caused, whether by the negligence of Pelco or otherwise.

The above warranty provides the Dealer with specific legal rights. The Dealer may also have additional rights, which are subject to variation from state
to state.

If a warranty repair is required, the Dealer must contact Pelco at [phone] or [phone] to obtain a Repair Authorization number (RA), and
provide the following information:

1. Model and serial number

2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number

3. Details of the defect or problem

If there is a dispute regarding the warranty of a product which does not fall under the warranty conditions stated above, please include a written
explanation with the product when returned.

Method of return shipment shall be the same or equal to the method by which the item was received by Pelco.

RETURNS

In order to expedite parts returned to the factory for repair or credit, please call the factory at [phone] or [phone] to obtain an authorization
number (CA number if returned for credit, and RA number if returned for repair).

All merchandise returned for credit may be subject to a 20% restocking and refurbishing charge.

Goods returned for repair or credit should be clearly identified with the assigned CA or RA number and freight should be prepaid. Ship to the appropriate
address below.

If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico, send goods to:

Service Department
Pelco
3500 Pelco Way
Clovis, CA 93612-5699

If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico and are instructed to return goods to the USA, you may do one of the
following:

If the goods are to be sent by a COURIER SERVICE, send the goods to:

Pelco
3500 Pelco Way
Clovis, CA 93612-5699 USA

®

Series products (multiplexers, server, and keyboard).

®

and fixed camera models, except the CC3701H-2, CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2, and

®

, CM6700/CM6800/CM9700 Series matrix, and DF5/DF8 Series fixed dome products.

®

, Esprit®, ExSite™, and PS20 scanners, including when used in continuous motion applications.

®

and WW5700 Series window wiper (excluding wiper blades).

™

Series distributed network-based video

If the goods are to be sent by a FREIGHT FORWARDER, send the goods to:

Pelco c/o Expeditors
473 Eccles Avenue
South San Francisco, CA 94080 USA
Phone: [phone]
Fax: [phone]

Pelco, the Pelco logo, Camclosure, Esprit, Genex, Legacy, and Spectra are registered trademarks of Pelco.

Endura and ExSite are trademarks of Pelco.

©Copyright 2002, Pelco. All rights reserved.

REVISION HISTORY

Manual # Date Comments

C2436M 9/01 Original version.
C2436M-A 7/02 Added instructions for fixed lens with auto iris.
C2436M-B 9/02 Revised installation instructions – bracket and camera assembled at factory. Added iris level

adjustment for fixed lens with auto iris.

[ 12 ] Pelco Manual C2436M-B (9/02)