Pelco MR3050 User Manual 2

Download

Page 1

C220M-C (7/99) MR3000/MR3050 Universal Monitor Mount

3500 Pelco Way, Clovis, CA 93612-5699 USA

In North America & Canada: Tel (800) 289-9100 FAX (800) 289-9150

International Customers: Tel (1-559) 292-1981 FAX (1-559) 348-1120

www.pelco.com

IMPORTANT SAFEGUARDS AND WARNINGS

Prior to installation and use of this product, the following WARNINGS should be observed.

1. Installation and servicing should only be done by qualified service personnel and conform to all local codes.

2. Installation shall be done in accordance with all local and national electrical and mechanical codes utilizing only approved materials.

3. Use only installation methods and materials capable of supporting four times the maximum specified load.

The product and/or manual may bear the follo wing marks:

This symbol indicates that there are important operating and maintenance instructions in the literature accompanying this unit.

Please thoroughly familiarize yourself with the information in this manual prior to installation and operation.

CAUTION:

RISK OF ELECTRIC SHOCK.

DO NOT OPEN.

DESCRIPTION

The MR3000 and MR3050 are universal monitor mounts engineered to safely mount a monitor from either a ceiling or a wall. They are designed for use in security systems, educational institutions, churches, hospitals, and other applications requiring flexibility in monitor mounting and positioning.

The mounts are adjustable to accommodate various sizes of monitors (refer to the section for dimensions). Two optional adapters are available: the MRWA for wall mounting and the MRCA for ceiling mounting. An 8-inch (20 cm) length of 1-1/2-inch (3.81 cm) NPT pipe is provided with the mount.

Specifications

CAUTION:

The mounting surface must be capable of support-

ing four times of the weight of the mount and monitor.

Recommended Mounts Adapters

MRWA Wall mount, uses six 5/16-inch diameter fasteners (not supplied). MRCA Ceiling mount, uses four 5/16-inch diameter fasteners (not supplied).

INSTALLATION

MRCA/MRWA Adapter Mounting

1. Determine the mounting location. Remember to allow for adequate clearance on all sides of the monitor.

2. Use the adapter mount as a template to mark the required mounting holes.

3. Using the necessary fasteners, attach the adapter mount to the chosen surface.

MR3000/MR3050 Installation

1. Determine the width that the base (item 1, Figure 1) must be positioned to accommodate the monitor. Allow room for the side brackets (item 2, Figure 1).

2. Attach the two base support brackets (item 13, Figure 1) to the base.

3. Thread the 8-inch (20 cm) pipe supplied into the ceiling/wall adapter.

4. Thread the collar adapter and attached crossbar (already assembled) onto the end of the 8-inch (20 cm) pipe.

5. Slide the side brackets (item 2, Figure 1) onto the crossbar and thread on the 1/4-20 bolts. Do not tighten bolts yet; you will do so in step 7.

6. Attach the base to the side brackets using the four 3/8-16 bolts supplied. Do not tighten bolts yet; you will do so in step 10.

7. Tighten the 1/4-20 bolts that attach the side brackets to the crossbar (installed in step 5).

Page 2

8. Attach the monitor to the base. If the monitor has removable rubber feet, remove the screws from the monitor feet and remove the feet. Use the same hardware to attach the monitor to the base.

9. Make any final adjustments in the pan angle of the assembly, then tighten set screws in upper part of collar to lock mount and collar in place.

10. Tilt the monitor to the desired angle and tighten bolts on each side of the side brackets.

11. Make all necessary electrical connections.

Page 3

Figure 1. MR3000/MR3050 Exploded Assembly Diagram

Table A. MR3000/MR3050 Exploded Assembly Parts List

Item Qty. Description Part Number

12Base

22Adjustable side bracket

31Crossbar

41Collar adapter MR30004103COMP 51Lock nut ZH1/213NUTCHN 62Set screw, 1/4-20 x 1/4-inch ZH1/420X.250S 76Screw, hex head, 1/4-20 x 1/2-inch ZH1/4-20X.500CH 86Flat washer ZH260X562X65C

91Modified fender washer MR30504104COMP 10 4 Bolt, 3/8-16 x 1/2-inch ZH3/816X.500SH 11 4 Flat washer ZH377X880X78 12 1 Bolt, 1/2-13 x 1-inch ZH1/213X1.00CH 13 2 Base support bracket

14 1 Pipe nipple, 8-inch L x 1-1/2-inch NPT

MR3000 MR30004000COMP MR3050 MR30504001COMP

MR3000 MR30004001COMP MR3050 MR30504003COMP

MR3000 MR30004005COMP MR3050 MR30504000COMP

MR3000 MR30004004COMP MR3050 MR30504002COMP

(not shown) MRU4207COMP

Page 4

Figure 2. MR3000/MR3050 Dimension Drawing

SPECIFICATIONS

Tilt Angle: Adjustable ±45° Maximum Load

MR3000: 40 lb (18 kg)

MR3050: 65 lb (29.45 kg) Construction: Steel Finish: Black polyester powder coat Dimensions: See Figure 2 Unit Weight

MR3000: 12 lb (5.44 kg)

MR3050: 20 lb (9.07 kg)

(Design and product specifications subject to change without notice.)

WARRANTY AND RETURN INFORMATION

WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below:

• Five years on FT/FR8000 Series fiber optic products.

• Three years on Genex® Series products (multiplexers, server, and keyboard).

• Three years on Camclosure® and fixed camera models, except the CC3701H-2,

CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2, and MC3651H-2X camera models, which have a five-year warranty.

• Two years on standard motorized or fixed focal length lenses.

• Two years on Legacy®, CM6700/CM6800/CM9700 Series matrix, and DF5/DF8 Series

fixed dome products.

• Two years on Spectra®, Esprit®, ExSite™, and PS20 scanners, including when used in continuous motion applications.

• Two years on Esprit® and WW5700 Series window wiper (excluding wiper blades).

• Eighteen months on DX Series digital video recorders, NVR300 Series network video

recorders, and Endura™ Series distributed network-based video products.months on DX Series digital video recorders, NVR300 Series network video recorders, Endura™ Series distributed network-based video products, and TW3000 Series twisted pair transmission products.

• One year (except video heads) on video cassette recorders (VCRs). Video heads will be covered for a period of six months.

• Six months on all pan and tilts, scanners or preset lenses used in continuous motion applications (that is, preset scan, tour and auto scan modes).

Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco shipment. All goods requiring warranty repair shall be sent freight prepaid to Pelco, Clovis, California. Repairs made necessary by reason of misuse, alteration, normal wear, or accident are not covered under this warranty.

Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from the specific use or application made of the Products. Pelco’s liability for any claim, whether based on breach of contract, negligence, infringement of any rights of any party or product liability, relating to the Products shall not exceed the price paid by the Dealer to Pelco for such Products. In no event will Pelco be liable for any special, incidental or consequential damages (including loss of use, loss of profit and claims of third parties) however caused, whether by the negligence of Pelco or otherwise.

The above warranty provides the Dealer with specific legal rights. The Dealer may also have additional rights, which are subject to variation from state to state.

REVISION HISTORY

Manual # Date Comments

C220M 5/91 Original version. C220M 4/93 Rev. A. Revised pages 2-5. New Figures 1 and 2 and Section 3.2 and 5.0 revised. C220M-B 11/94 Rev. B. Revised to 2-column Format. Incorporated new Figure 1 and revised Sections 2.2 and 4.0 per ECO #94-379. C220M-C 7/99 Added MR3050 mount. Added

Recommended Mount Adapters

If a warranty repair is required, the Dealer must contact Pelco at (800)289-9100 or (559) 292-1981 to obtain a Repair Authorization number (RA), and provide the following information:

1. Model and serial number

2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number

3. Details of the defect or problem If there is a dispute regarding the warranty of a product which does not fall under the

warranty conditions stated above, please include a written explanation with the product when returned.

Method of return shipment shall be the same or equal to the method by which the item was received by Pelco.

RETURNS In order to expedite parts returned to the factory for repair or credit, please call the factory at (800) 289-9100 or (559) 292-1981 to obtain an authorization number (CA number if returned for credit, and RA number if returned for repair). All merchandise returned for credit may be subject to a 20% restocking and refurbishing charge.

Goods returned for repair or credit should be clearly identified with the assigned CA or RA number and freight should be prepaid. Ship to the appropriate address below. If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico, send goods to:

If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico and are instructed to return goods to the USA, you may do one of the following: If the goods are to be sent by a COURIER SERVICE, send the goods to:

If the goods are to be sent by a FREIGHT FORWARDER, send the goods to:

Service Department Pelco 3500 Pelco Way Clovis, CA 93612-5699

Pelco 3500 Pelco Way Clovis, CA 93612-5699 USA

Pelco c/o Expeditors 473 Eccles Avenue South San Francisco, CA 94080 USA Phone: 650-737-1700 Fax: 650-737-0933

section. Modified specifications. Updated to new format.