Pelco IR850M-120, IR940S-30, IR940M-60, IR940L-110, IR850S-65 User Manual

IR850, IR940 & WLED
LED ILLUMINATORS

C3934M (9/13)

Contents

Important Safety Instructions ............................................................................ 3

Important Notices

Regulatory Notices .................................................................................... 4

Radio and Television Interference..............................................................4

Installation Steps – Quick Guide ....................................................................... 5

Complete Set up and Installation ...................................................................... 6

Remote Controller ............................................................................................. 8

LED Status Feedback System .......................................................................... 9

Standard Bracket Dimension Drawings ............................................................ 10

Optional Mounting Bracket ............................................................................... 11

Optional Mounting Bracket Dimension Drawings ............................................. 11

Optional Interchangeable Diffuser System ....................................................... 12

Specifications .................................................................................................... 13

Certifications and Ratings ................................................................................. 13

Illuminator Dimension Drawings ....................................................................... 14

Troubleshooting Guide ...................................................................................... 17

2 www.pelco.com C3934M (9/13)

Important Safety Instructions

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accordance with the manufacturer’s
instructions.

8. Only use attachments/accessories specified by the manufacturer.

9. Refer all servicing to qualified service personnel. Servicing is required when the
apparatus has been damaged in any way, such as power-supply cord or plug is
damaged, liquid has been spilled or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture, does not operate normally, or has
been dropped.

10. Installation should be done only by qualified personnel and conform to all local codes.

11. Unless the unit is specifically marked as a NEMA Type 3, 3R, 3S, 4, 4X, 6, 6P
enclosure or marked as suitable for use in wet locations, it is designed for indoor use
only and it must not be installed where exposed to rain and moisture.

12. Use only installation methods and materials capable of supporting four times the
maximum specified load.

13. Use stainless steel hardware to fasten the mount to outdoor surfaces.

CAUTION: These servicing instructions are for use by qualified service personnel only.
To reduce the risk of electric shock do not perform any servicing other that contained in
the operating instructions unless you are qualified to do so.

CAUTION: IR emitted from this product – Risk Group 2. Avoid prolonged eye exposure
or use appropriate shielding or eye protection at distances of less than 1500mm.
Risk Group 2 for cornea/lens infrared hazard. At a distance of more than 1500mm for all
IR850 products or 1300mm for all IR940 products the unit is in the exempt group.

3www.pelco.comC3934M (9/13)

Important Notices

REGULATORY NOTICES

This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.

RADIO AND TELEVISION INTERFERENCE

This equipment has been tested and found to comply with the limits of a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and,
if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However there is no guarantee that the
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the receiver.

• Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

You may also find helpful the following booklet, prepared by the FCC: “How to Identify
and Resolve Radio-TV Interference Problems.” This booklet is available from the U.S.
Government Printing Office, Washington D.C. 20402.

Changes and Modifications not expressly approved by the manufacturer or registrant
of this equipment can void your authority to operate this equipment under Federal
Communications Commission’s rules.

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

WARRANTY STATEMENT

For information about Pelco’s product warranty and thereto related information, refer to

www.pelco.com/warranty

4 www.pelco.com C3934M (9/13)

Installation Steps – Quick Guide

1. IR850, IR940 & WLED Illuminators are factory set

and delivered with a 35˚ beam width. To alter
to 10˚, simply remove Interchangeable Diffuser
System (IDS) lens. To alter to 60˚, replace
with the other IDS lens supplied. See detailed
instructions later in this document.

2. Mount Illuminator.

3. Connect the Illuminator to a properly rated low

voltage power supply
(12-24V AC/DC).

4. Complete configuration and final set-up

using Remote Controller (this is an optional
accessory).

Wiring - six core cable

Black: AC/DC-

Red: AC/DC+

White: Photocell Following Contact

Yellow: Photocell Following Contact

Orange: Telemetry Input

Purple: Telemetry Input

(1) Volt Free Output; Non-polarity sensitive

(2) Volt Free/Dry Contact or TTL Input

(see step 4 for more details)

(2)

(2)

Photocell

(1)

(1)

Cable

Breather

Gland

Factory Default Set-Up:

35˚ Beam Angle
Max 100% Power
Telemetry Input - closed
Photocell sensitivity - MID
Status LEDs – ON
Programming function will auto-disable after 4 weeks

5www.pelco.comC3934M (9/13)

Complete Set up and Installation

Step 1. Select different beam angle – if required

All IR850, IR940 & WLED illuminators are set and delivered with a 35˚ beam width
angle. To alter to 10˚, simply remove Interchangeable Diffuser System (IDS) lens.
To alter to 60˚, replace with additional IDS lens supplied.

Other angle IDS lenses are available to order: 80˚ and 120˚.

All IDS lenses will be clearly marked with the angle which they will produce when
inserted into IR850, IR940 or WLED illuminator.

Please handle IDS lenses with care – and do not touch optical film.

Only 1 IDS lens can be inserted into the product at anytime. The product cannot
accommodate multiple IDS lenses at the same time.

We would recommend that power is turned off when replacing IDS lenses.

Remove base plate from unit using 2.5mm allen/hex key. Remove any IDS lens
currently installed and insert the required IDS lens.

Re-attach the base.

IMPORTANT NOTE: Ensure that the gasket is correctly located and the screws
fastened tightly to ensure and maintain IP66 rating of the product.

6 www.pelco.com C3934M (9/13)