Pelco IP110-F User Manual

INSTALLATION

IP110-F Flush Mount Adapter

C2238M (12/08)

Important Safety Instructions

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Only use attachments/accessories specified by the manufacturer.

6. Installation should be done only by qualified personnel and conform to all local codes.

7. Use only installation methods and materials capable of supporting four times the maximum
specified load.

8. Only use replacement parts recommended by Pelco.

6 C2238M (12/08)

Description

The IP110-F is a flush mount adapter specifically designed for the IP110 Camclosure® integrated camera
system.

PARTS LIST

Qty Description

1 IP110-F flush mount adapter
2 Screws, 8-32 x 3-inch, Phillips pan head
2 Screws, 8-32 x 0.5-inch, Phillips pan head
4 O-rings, 0.7-inch diameter
4 Flat washers, #8 stainless steel
2 Spring paddles
1 IP110-F Flush Mount Adapter Installation manual

C2238M (12/08) 7

Installation

To install the IP110-F flush mount adapter, install the IP110 camera as described in the IP110 Series
Camclosure Installation manual (C3432M) and include the following exceptions using Figure 1 as a guide:

1. Insert the IP110-F adapter between the cover and the back box. Make sure to point the rounded
portion of the outside edge of the adapter and the hollowed portion of the two holes in the adapter
toward the back box.

2. Use the two 8-32 x 0.5-inch Philips pan head screws supplied with the adapter to secure the cover
to the back box. Do not use the screws supplied with the camera. Additional flat washers and

0.7-inch diameter O-rings are also supplied, if needed.

3. Insert two 8-32 x 3-inch Phillips pan head screws (supplied) into the holes in the adapter.

4. Attach the spring paddles (supplied) to the 8-32 x 3-inch Phillips pan head screws (refer to Figure 1).

COVER ASSEMBLY

O-RING, 0.7-INCH DIAMETER

CEILING LEVEL

FLAT WASHERS,

#8 STAINLESS STEEL

(2) SCREWS, 8-32 x 0.5-INCH

PHILLIPS PAN HEAD

SPRING PADDLE

ADAPTER RING

BACK BOX

(2) SCREWS, 8-32 x 3-INCH
PHILLIPS PAN HEAD

DOME ASSEMBLY

Figure 1. IP110-F Installation

8 C2238M (12/08)

SUSPENDED CEILING INSTALLATION

To install the IP110 with the IP110-F in a suspended ceiling:

1. Cut a 6.5-inch (16.5-centimeter) diameter hole in the ceiling tile.

2. Pull all wiring through the hole in the ceiling tile and terminate all wires.

3. Connect your wiring to the dome using one of the following options:

• Plug the network cable into the RJ-45 connector on the side of the dome.

• If the network has no Power over Ethernet (PoE), connect a 24 VAC Class 2 power supply to

the 24 VAC power connector.

Refer to the IP110 Series Camclosure Installation manual (C3432M) for wiring connections.

4. Attach the dome to the ceiling tile (refer to Figure 2).

a. Stabilize the spring paddles by applying pressure to the 8-32 x 0.5-inch Philips pan head screws.

b. With the screws stabilized, insert the spring paddles and dome into the hole in the ceiling tile.

NOTE: Be sure to route all wiring away from the spring paddles.

c. Once the spring paddles have cleared the hole in the ceiling tile, release the screws. You do

not need to provide additional support for the dome; the paddles will hold the dome in place.

WARNING: Do not overtighten the mounting hardware.

d. Tighten the screws completely to secure the ceiling tile between the spring paddles and the

dome.

CEILING LEVEL

COVER ASSEMBLY

SPRING PADDLE

(2) SCREWS,
8-32 x 3-INCH
PHILLIPS PAN HEAD

ADAPTER RING

Figure 2. Suspended Ceiling Installation

C2238M (12/08) 9

Specifications

MECHANICAL

Mounting Method Attach to the IP110 with supplied hardware

GENERAL

Construction Aluminum
Finish Gray polyester powder coat
Unit Weight 0.36 lb (0.16 kg)

7.34

(186.47)

5.33

(135.37)

0.24

(6.14)

Ø 0.19 (4.80), 2X

6.11

(155.10)

NOTE: VALUES IN PARENTHESES ARE CENTIMETERS; ALL OTHERS ARE INCHES.

10 C2238M (12/08)

PRODUCT WARRANTY AND RETURN INFORMATION

WARRANTY

Pelco will repair or replace, without charge, an y merchandise proved defective in material or workmanship for a period of one year after the date of
shipment.

Exceptions to this warranty are as noted below:

• Five years:
– Fiber optic products
– TW3 000 Series unshielded twisted pair (UTP) transmission products
– CC370 1H-2, CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2, and MC3651H-2X camera models

• Three years:
– Pe lco-branded fixed camera models (CCC1390H Series, C10DN Series, C10CH Series, IP3701H Series, and IX Series)
– EH150 0 Series enclosures

®

– Spectra

IV products (including Spectra IV IP)

– Cam closure
– DX Se ries digital video recorders, DVR5100 Series digital video recorders, Digital Sentry

– En dura
– Ge nex® Series products (multiplexers, server, and keyboard)
– PMCL200/300/400 Series LCD monitors

• Two years:
– S tandard varifocal, fixed focal, and motorized zoom lenses.
– DF5/DF8 Series fixed dom e products
– Lega cy® Series integrated positioning systems
– Spectra III™, Spectra Mini, Spectra Mini IP, Esprit®, ExSite®, and PS20 scanners, including when u sed in continuous motion applications.
– Espr it Ti and TI2500 Series thermal imaging products
– Espr it and WW5700 Series window wiper (excluding wiper blades).
– CM 6700/CM6800/CM9700 Series matrix
– Di gital Light Processing (DLP®) displays (except lamp and color wheel). The lamp and color wheel will be covered for a period of 90 days.

– Inte lli-M

•One year:
– Video cassette record ers (VCRs), except video heads. Video heads will be covered for a period of six months.

• Six months:
– Al l pan and tilts, scanners, or preset lenses used in continuous motion applicatio ns (preset scan, tour, and auto scan modes).

Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco shipment. All goods requiring warranty repair shall be sent
freight prepaid to a Pelco designated locatio n. Repairs made necessary by reason of misuse, alteration, normal wear, or accident are no t covered under
this warranty.

Pelco assumes no risk and shall be subject to no li ability for damages or loss resulting from the specific use or application made of the Products.
Pelco’s liability for any claim, whether based on breach of contract, negligence, infringement of any rights of any party or product liability, relating to
the Products shall not exceed the price paid by the Dealer to Pelco for such Products. In no event will Pelco be liable for any special, incidental, or
consequential damages (including loss of use, loss of profit, and claims of third parties) however caused, whether by the negligence of Pelco or
otherwise.

The above warranty provides the Dealer with spe cific legal rights. The Dealer may also have additional right s, which are subject to variation from state
to state.

If a warranty repair is required, the Dealer must contact Pelco at [phone] or [phone] to obtain a Repair Authorization number (RA), and
provide the following information:

1. Model and serial number

2. Date of shipment, P.O. number, sales order number, or Pelco invoice number

3. Details of the defect or problem

If there is a dispute regarding the warranty of a product that does not fall un der the warranty conditions stated above, please include a written
explanation with the product wh en returned.

Method of return shipment shall be the same or equal to the method by which the item was received by Pelco.

RETURNS

To expedite parts returned for repair or credit, please call Pelco at [phone] or [phone] to obtain an authorization number (CA number if
returned for credit, and RA number if returned for repair) and designated return location.

All merchandise returned for credit may be subject to a 20 percent restocking and refurbishing charge.

Goods returned for repair or credit should be clearly identified with the assigned CA or RA number and freight should be prepaid

®

Series (IS, ICS, IP) integrated camera systems

recorders, and NVR300 Series network video r ecorders

®

Series distributed network-based video pro ducts

The air filter is not covered under warranty.

®

eIDC controllers

®

Series hardware products, DVX Series digital vide o

12-23-08

REVISION HISTORY

Manual # Date Comments

C2238M 12/08 Original version.

Pelco, the Pelco logo, Camclosure, Digital Sentry, Endura, Esprit, ExSite, Genex, Intelli-M, Legacy, and Spectra are registered trademarks of Pelco, Inc.
Spectra III is a trademark of Pelco, Inc. © Copyright 2008, Pelco, Inc. All rights reserved.
DLP is a registered trademark of Texas Instruments Incorporated.

www.pelco.com

Pelco, Inc. Worldwide Headquarters 3500 Pelco Way Clovis, California 93612 USA

USA & Canada Tel [phone] Fax [phone]

International Tel [phone] Fax [phone]