Pelco ICS200-CM User Manual

C298M-B (5/01) ICS200-CM Corner Mount

3500 Pelco Way Clovis, CA 93612-5699 USA

In North America & Canada: Tel (800) 289-9100 FAX (800) 289-9150

International Customers: Tel +1(559) 292-1981 FAX +1(559) 348-1120

www.pelco.com

IMPORTANT SAFEGUARDS AND WARNINGS

Prior to installation and use of this product, the following WARNINGS should be observed.

1. Installation and servicing should only be done by qualified service personnel and conform to all local codes.

2. Only use replacement parts recommended by Pelco.

3. The installation method and materials should be capable of supporting four times the maximum specified load.

4. To prevent damage from water leakage when installing a mount outdoors on a roof or wall, apply sealant around the bolt holes between the mount and mounting surface.

DESCRIPTION

The ICS200-CM is a corner mount specifically designed for the ICS200 Camclosure™ Integrated Camera System. The mount is the perfect solution for installing the ICS200 in a tight area such as a stairwell, hallway, or elevator.

INSTALLATION

To install the ICS200-CM do the following (refer to Figure 1):

1. Use the ICS200-CM as a template and mark the four fastener positions on the mounting surface. Prepare the surface.

NOTE:

When installing flush against a ceiling, measure down 6.50-inches from the ceiling (refer to Figure 1). A .50-inch clearance, between the top of the corner mount and the ceiling, is required to complete the installation of the ICS200 to the ICS200-CM.

2. Route the wiring/cabling through the mount. Attach the ICS200-CM to the surface with the appropriate hardware (not supplied). If you install the corner mount outdoors, apply a sealant between the mount and the mounting surface.

3. You must reorient the camera module inside the ICS200 when using the ICS200-CM corner mount. Refer to the ICS200 Installation Manual for instructions on how to install and adjust the camera module.

4. Use the three screws provided with the corner mount and attach the base of the

.5"

CLEARANCE

ICS200 to the ICS200-CM. To complete the installation, refer to the Installation and Operation manual supplied with the

ICS200-CM

ICS200.

6.5"

Figure 1.

ICS200-CM Installation

BASE OF ICS200

00056

6.3

(16.0)

SPECIFICATIONS

GENERAL

Construction: Aluminum Finish: Gray polyester powder coat Maximum Load: 8 lb (3.63 kg) Dimensions: See Figure 2 Weight: .70 lb (.32 kg)

(Design and product specifications subject to change without notice.)

3.3

(8.4)

NOTE: VALUES IN PARENTHESES ARE CENTIMETERS; ALL OTHERS ARE IN INCHES.

2.4

(6.1)

Figure 2. ICS200-CM Dimension Drawing

WARRANTY AND RETURN INFORMATION

WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below:

• Five years on FT/FR8000 Series fiber optic products.

• Three years on Genex® Series products (multiplexers, server, and keyboard).

• Three years on Camclosure® and fixed camera models, except the CC3701H-2, CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2, and MC3651H-2X camera models, which have a five-year warranty.

• Two years on standard motorized or fixed focal length lenses.

• Two years on Legacy®, CM6700/CM6800/CM9700 Series matrix, and DF5/DF8 Series fixed dome products.

• Two years on Spectra®, Esprit®, ExSite™, and PS20 scanners, including when used in continuous motion applications.

• Two years on Esprit® and WW5700 Series window wiper (excluding wiper blades).

• Eighteen months on DX Series digital video recorders, NVR300 Series network video recorders, and Endura™ Series distributed network-based video products.months on DX Series digital video recorders, NVR300 Series network video recorders, Endura™ Series distributed network-based video products, and TW3000 Series twisted pair transmission products.

• One year (except video heads) on video cassette recorders (VCRs). Video heads will be covered for a period of six months.

• Six months on all pan and tilts, scanners or preset lenses used in continuous motion applications (that is, preset scan, tour and auto scan modes).

Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco shipment. All goods requiring warranty repair shall be sent freight prepaid to Pelco, Clovis, California. Repairs made necessary by reason of misuse, alteration, normal wear, or accident are not covered under this warranty.

Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from the specific use or application made of the Products. Pelco’s liability for any claim, whether based on breach of contract, negligence, infringement of any rights of any party or product liability, relating to the Products shall not exceed the price paid by the Dealer to Pelco for such Products. In no event will Pelco be liable for any special, incidental or consequential damages (including loss of use, loss of profit and claims of third parties) however caused, whether by the negligence of Pelco or otherwise.

The above warranty provides the Dealer with specific legal rights. The Dealer may also have additional rights, which are subject to variation from state to state.

01466

If a warranty repair is required, the Dealer must contact Pelco at (800)289-9100 or (559) 292-1981 to obtain a Repair Authorization number (RA), and provide the following information:

1. Model and serial number

2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number

3. Details of the defect or problem If there is a dispute regarding the warranty of a product which does not fall under the

warranty conditions stated above, please include a written explanation with the product when returned.

Method of return shipment shall be the same or equal to the method by which the item was received by Pelco.

RETURNS In order to expedite parts returned to the factory for repair or credit, please call the factory at (800) 289-9100 or (559) 292-1981 to obtain an authorization number (CA number if returned for credit, and RA number if returned for repair). All merchandise returned for credit may be subject to a 20% restocking and refurbishing charge.

Goods returned for repair or credit should be clearly identified with the assigned CA or RA number and freight should be prepaid. Ship to the appropriate address below. If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico, send goods to:

If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico and are instructed to return goods to the USA, you may do one of the following: If the goods are to be sent by a COURIER SERVICE, send the goods to:

If the goods are to be sent by a FREIGHT FORWARDER, send the goods to:

Service Department Pelco 3500 Pelco Way Clovis, CA 93612-5699

Pelco 3500 Pelco Way Clovis, CA 93612-5699 USA

Pelco c/o Expeditors 473 Eccles Avenue South San Francisco, CA 94080 USA Phone: 650-737-1700 Fax: 650-737-0933

REVISION HISTORY

Manual # Date Comments

C298M 8/00 Original version. C298M-A 10/00 Revised Figure 1. C298M-B 5/01 Added instructions for mounting flush to ceiling