Pelco ICS110-PG User Manual

INSTALLATION

ICS110-PG
Pendant Mount

®

Adapter

C2214M (2/05)

Important Safety Instructions

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Only use attachments/accessories specified by the manufacturer.

6. Installation should be done only by qualified personnel and conform to all local codes.

7. Use only installation methods and materials capable of supporting four times the maximum
specified load.

8. Only use replacement parts recommended by Pelco.

C2214M (2/05) 3

4 C2214M (2/05)

Description

The ICS110-PG is a pendant mount adapter specifically designed for the ICS110 Camclosure®
integrated camera system. The pendant adapter modifies the surface mount Camclosure dome for
pendant installations using a 1.5-inch NPT mount, such as the SWM-GY or IWM-GY mount..

Installation

To install the ICS110-PG refer to Figure 1 and do the following:

1. Install the 1.5-inch NPT mount; refer to the instructions supplied with the mount. Bring the
power and video wiring for the system through the mount.

2. Route the wiring through the ICS110-PG. Apply thread compound (provided) to the threads of
the ICS110-PG, and then screw the ICS110-PG onto the mount.

3. Route the wiring through the back box of the ICS110, and use the provided hardware to attach
the back box to the ICS110-PG mount adapter.

4. To complete the installation, refer to the Installation/Operation manual supplied with the
ICS110 Camclosure integrated camera system.

ICS110-PG

BACK BOX

Figure 1.

C2214M (2/05) 5

ICS110-PG Installation

Specifications

MECHANICAL

Mounting Method Attach to the ICS110 with supplied hardware; install to a mount with

GENERAL

Construction Aluminum
Finish Gray polyester powder coat
Unit Weight 0.73 lb (0.33 kg)

1.5-inch NPT pipe (such as the SWM-GY or IWM-GY mount)

5.82 (14.78)

0.74

(1.88)

3.66

(9.29)

NOTE: VALUES IN PARENTHESES ARE CENTIMETERS;

ALL OTHERS ARE IN INCHES.

1.50” NPT

6 C2214M (2/05)

PRODUCT WARRANTY AND RETURN INFORMATION

WARRANTY

Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship
shipment.

Exceptions to this warranty are as noted below:

• Five years on FT/FR8000 Series fiber optic products and the following fixed camera models: CC3701H-2, CC3701H-2X, CC3751H-2, CC3651H-2X,
MC3651H-2, and CC3651H-2X.

• Three years on all other fixed camera models (including Camclosure
keyboard).

•Two years on all standard motorized or fixed focal length lenses.

•Two years on Legacy®, CM6700/CM6800/CM8500/CM9500/CM9700 Series Matrix, DF5 and DF8 Series Fixed Dome products.

•Two years on Spectra®, Esprit®, and PS20 Scanners, including when used in continuous motion applications.

•Two years on Esprit® and WW5700 Series window wiper (excluding wiper blades).

• Eighteen months on DX Series digital video recorders and NVR300 Series network video recorders, and all Endura™ Series distributed network based
video products.

• One year (except video heads) on video cassette recorders (VCRs). Video heads will be covered for a period of six months.

• Six months on all pan and tilts, scanners or preset lenses used in continuous motion applications (that is, preset scan, tour and auto scan modes).

Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco shipment. All goods requiring warranty repair shall be sent freight
prepaid to Pelco, Clovis, California. Repairs made necessary by reason of misuse, alteration, normal wear, or accident are not covered under this
warranty.

Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from the specific use or application made of the Products. Pelco’s
liability for any claim, whether based on breach of contract, negligence, infringement of any rights of any party or product liability, relating to the Products
shall not exceed the price paid by the Dealer to Pelco for such Products. In no event will Pelco be liable for any special, incidental or consequential dam­ages (including loss of use, loss of profit and claims of third parties) however caused, whether by the negligence of Pelco or otherwise.

The above warranty provides the Dealer with specific legal rights. The Dealer may also have additional rights, which are subject to variation from state
to state.

If a warranty repair is required, the Dealer must contact Pelco at [phone] or [phone] to obtain a Repair Authorization number (RA), and
provide the following information:

1. Model and serial number

2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number

3. Details of the defect or problem

If there is a dispute regarding the warranty of a product which does not fall under the warranty conditions stated above, please include a written expla­nation with the product when returned.

Method of return shipment shall be the same or equal to the method by which the item was received by Pelco.

®

Integrated Camera Systems) and Genex® Series (multiplexers, server, and

RETURNS

In order to expedite parts returned to the factory for repair or credit, please call the factory at [phone] or [phone] to obtain an authorization
number (CA number if returned for credit, and RA number if returned for repair).

All merchandise returned for credit may be subject to a 20% restocking and refurbishing charge.

Goods returned for repair or credit should be clearly identified with the assigned CA or RA number and freight should be prepaid. Ship to the appropriate
address below.

If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico, send goods to:

Service Department
Pelco
3500 Pelco Way
Clovis, CA 93612-5699

If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico and are instructed to return goods to the USA, you may do one of the
following

:

If the goods are to be sent by a COURIER SERVICE, send the goods to:

Pelco
3500 Pelco Way
Clovis, CA 93612-5699 USA

If the goods are to be sent by a FREIGHT FORWARDER, send the goods to:

Pelco c/o Expeditors
473 Eccles Avenue
South San Francisco, CA 94080 USA
Phone: [phone]
Fax: [phone]

for a period of one year

after the date of

REVISION HISTORY

Manual # Date Comments

C2214M 2/05 Original manual.

Pelco, the Pelco logo, and Camclosure are registered trademarks of Pelco. ©Copyright 2005, Pelco. All rights reserved.

®

Worldwide Headquarters

3500 Pelco Way

Clovis, California 93612 USA

USA & Canada

Tel: [phone]

Fax: [phone]

International

Tel: [phone]

Fax: [phone]

www.pelco.com

ISO9001

United States|Canada|United Kingdom|The Netherlands|Singapore|Spain|Scandinavia|France|Middle East