Pelco ICISA6500 User Manual

ICISA6500

®

Inter-Check

Interface Cable

Installation/Operation Manual

C1053M (7/98)

1.0 WARNINGS Prior to installation and use of this product, the following WARNINGS should be

observed.

1. Installation and servicing should only be done by qualified service personnel
and conform to all local codes.

2. Only use replacement parts recommended by Pelco.

The product and/or manual may bear the following marks:

This symbol indicates that dangerous voltage constituting a risk of elec­tric shock is present within this unit.

This symbol indicates that there are important operating and mainte­nance instructions in the literature accompanying this unit.

Please thoroughly familiarize yourself with the information in this

Pelco • 3500 Pelco Way, Clovis, CA 93612-5699 • USA • www.pelco.com
In North America and Canada: Tel [phone] • FAX [phone]

International Customers: Tel [phone] or FAX [phone]

manual prior to installation and operation.

2.0 DESCRIPTION The ICISA6500 is an Inter-Check

register.

®

interface cable for the Samsung 6500 cash

3.0 INSTALLATION 1. Make sure you have the following equipment before you begin the installation:

1 ICI1000S or ICI2000D Inter-Check® Register Interface
1 ICI1000WK or ICI2000WK Wiring Kit
1 ICISA6500 Interface Cable for each register

NOTE:

If you have an ICI2000D in­terface and two registers, the instruc­tions apply to both registers.

NOTE:

To receive data from the
Samsung 6500, the protocol must
be reset to RS-232 STANDARD
PRINTER and the communication
parameters must be set for DATA
NON-INVERTED. (Executing a
PIM Default Load does not auto­matically set the channel param­eters to the values listed in Table B.)

2. Connect a coaxial cable between the port labeled VIDEO OUT on the Inter­Check® and a CCTV monitor. Connect a coaxial cable between your camera
and the port labeled VIDEO IN on the Inter-Check
type of video coaxial cable to use.

®

. Refer to Table A for the

Table A. Video Coaxial Cable Requirements

Cable Type* Maximum Distance

RG59/U 750 ft (229 m)

RG6/U 1,000 ft (305 m)

RG11/U 1,500 ft (457 m)

* Minimum cable requirements:

75 ohms impedance
All-copper center conductor
All-copper braided shield with 95% braid coverage

3. Power up all units.

4. In the programming mode on the Inter-Check®, go to the DIAGNOSTICS MENU
and select the (DL) PIM DEFAULT LOAD option. (Refer to the proper ICI1000S
or ICI2000D manual for menu programming instructions.)

It is best to enable the Default Load option even if your installation does not
require a PIM module. The Default Load sets all Inter-Check® communication
parameters to the specific values needed to communicate with the ICI1000PIM
module.

5. When the prompt “SYSTEM INITIALIZED” appears on the monitor, return to
the PROGRAMMING MENU and set the data protocol for RS-232 STANDARD
PRINTER and communication parameters to DATA NON-INVERTED. (Refer
to Table B for the Inter-Check® communication parameters for the Samsung

6500.)

Table B. Inter-Check® Default Communication Parameters

Communication Parameters Protocol

9600 BAUD RS-232 STANDARD PRINTER
8 BITS
NO PARITY
NRZ
ASCII
DATA NON-INVERTED

6. Turn off and unplug the cash register.

7. Connect the ICISA6500 interface cable into an available Com Port on your cash
register. Com 1 is preferred but you can also use Com 2. (Refer to Figure 1.)

8. Wire the ICISA6500 to the Inter-Check®, as shown in your ICI1000S or
ICI2000D manual, using the wiring kit diagram appropriate for RS-232 com­munication.

2 Pelco Manual C1053M (7/98)

9. Program register Com Port 1 or 2, according to the following instructions, to
enable the selected Com Port and send journal printer data to the Inter-Check®.

Programming Com 1

a. Turn the register key to P.
b. Press 60 and Subtotal.
c. Press 50, X/Time, 2 and Subtotal.
d. Press 51, X/Time, 0 and Subtotal.
e. Press 52, X/Time, 0 and Subtotal.
f. Press 53, X/Time, 8 and Subtotal.
g. Finish programming by pressing Cash.
h. Turn key back to Reg to run transactions.

Programming Com 2

a. Turn the register key to P.
b. Press 60 and Subtotal.
c. Press 60, X/Time, 2 and Subtotal.
d. Press 61, X/Time, 0 and Subtotal.
e. Press 62, X/Time, 0 and Subtotal.
f. Press 63, X/Time, 8 and Subtotal.
g. Finish programming by pressing Cash.
h. Turn key back to Reg to run transactions.

10. Finally, run a transaction on the register. The transaction should appear on
your security monitor exactly as it is printed on the printer journal.

4.0 SPECIFICATIONS GENERAL

Environment: Indoor

Operating Temperature: 32° to 120°F (0° to 49°C)

Weight: Unit Shipping

Connectors: Two DB-9 connectors

1.0 lb (0.45 kg) 2.0 lb (0.91 kg)

One RJ-14 connector

(Design and product specifications subject to change without notice.)

SAMSUNG

COM PORT 2

COM PORT 1

Figure 1. Samsung 6500 Com Ports

Pelco Manual C1053M (7/98) 3

5.0 WARRANTY AND
RETURN INFORMATION

Pelco, the Pelco logo, Camclosure, Esprit,
Genex, Legacy, and Spectra are registered
trademarks of Pelco.
Endura and ExSite are trademarks of Pelco.

© Copyright 1998, Pelco. All rights reserved.

WARRANTY

Pelco will repair or replace, without charge, any merchandise proved defective in material or
workmanship for a period of one year after the date of shipment.

Exceptions to this warranty are as noted below:

• Five years on FT/FR8000 Series fiber optic products.

• Three years on Genex

• Three years on Camclosure
CC3751H-2, CC3651H-2X, MC3651H-2, and MC3651H-2X camera models, which have a five­year warranty.

• Two years on standard motorized or fixed focal length lenses.

• Two years on Legacy
dome products.

• Two years on Spectra
continuous motion applications.

• Two years on Esprit

• Eighteen months on DX Series digital video recorders, NVR300 Series network video

recorders, and Endura

• One year (except video heads) on video cassette recorders (VCRs). Video heads will be
covered for a period of six months.

• Six months on all pan and tilts, scanners or preset lenses used in continuous motion applications
(that is, preset scan, tour and auto scan modes).

Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco shipment.
All goods requiring warranty repair shall be sent freight prepaid to Pelco, Clovis, California. Repairs
made necessary by reason of misuse, alteration, normal wear, or accident are not covered under

®

Series products (multiplexers, server, and keyboard).

®

and fixed camera models, except the CC3701H-2, CC3701H-2X,

®

, CM6700/CM6800/CM9700 Series matrix, and DF5/DF8 Series fixed

®

, Esprit®, ExSite™, and PS20 scanners, including when used in

®

and WW5700 Series window wiper (excluding wiper blades).

™

Series distributed network-based video products.

this warranty.
Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from the

specific use or application made of the Products. Pelco’s liability for any claim, whether based on
breach of contract, negligence, infringement of any rights of any party or product liability, relating
to the Products shall not exceed the price paid by the Dealer to Pelco for such Products. In no event
will Pelco be liable for any special, incidental or consequential damages (including loss of use, loss
of profit and claims of third parties) however caused, whether by the negligence of Pelco or
otherwise.

The above warranty provides the Dealer with specific legal rights. The Dealer may also have
additional rights, which are subject to variation from state to state.

If a warranty repair is required, the Dealer must contact Pelco at [phone] or [phone]
to obtain a Repair Authorization number (RA), and provide the following information:

1. Model and serial number

2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number

3. Details of the defect or problem

If there is a dispute regarding the warranty of a product which does not fall under the warranty
conditions stated above, please include a written explanation with the product when returned.
Method of return shipment shall be the same or equal to the method by which the item was received
by Pelco.

RETURNS

In order to expedite parts returned to the factory for repair or credit, please call the factory at (800)
289-9100 or [phone] to obtain an authorization number (CA number if returned for credit,
and RA number if returned for repair).

All merchandise returned for credit may be subject to a 20% restocking and refurbishing charge.
Goods returned for repair or credit should be clearly identified with the assigned CA or RA number

and freight should be prepaid. Ship to the appropriate address below.
If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico, send goods to:

Service Department
Pelco
3500 Pelco Way
Clovis, CA 93612-5699

If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico and are instructed
to return goods to the USA, you may do one of the following:
If the goods are to be sent by a COURIER SERVICE, send the goods to:

Pelco
3500 Pelco Way
Clovis, CA 93612-5699 USA

If the goods are to be sent by a FREIGHT FORWARDER, send the goods to:

Pelco c/o Expeditors
473 Eccles Avenue
South San Francisco, CA 94080 USA
Phone: [phone]
Fax: [phone]

4 Pelco Manual C1053M (7/98)