Pelco ICIICISS45 User Manual

C1054M (6/99)
ICIICISS45
Inter-Check® Interface Cable

®

300 W. Pontiac Way,
Clovis, CA 93612-5699
USA

In North America & Canada:
Tel [phone]
FAX [phone]
DataFAX [phone]

International Customers:
Tel [phone]
FAX [phone]
DataFAX (1-559) 292-0435

Pelco Online
http://www.pelco.com

DESCRIPTION

The ICIICISS45 Inter-Check® interface cable is designed to connect an ICL/Fujitsu ISS45 sys­tem terminal to the Inter-Check® ICI1000S Series video text inserter. The interface cable con­sists of a printed circuit board, two DB25 connectors (male and female), and a 6-foot (1.8 m)
data cable with an RJ-14 connector.

INSTALLATION

The following items are supplied:
1 ICIICISS45 Inter-Check® interface cable

1 CN17-0111-0002 adapter, 25-pin (F) to 9-pin (M)
1 CN17-0211-0001 adapter, 25-pin (M) to 9-pin (F)

Refer to Figure 1.

1. Turn off power to the ISS45 terminal.

2. If the ISS45 terminal is equipped with a customer pole display, unplug the cable connec­tor from port 3.

3. Plug the CN17-0111-0002 adapter (supplied) into the 9-pin port 3 of the ISS45 terminal.

4. Set the SW1 switch on the ICIICISS45 interface cable in the position toward the gray data
cable.

5. Plug the ICIICISS45 interface cable connector into the CN17-0111-0002 adapter socket.
If the ISS45 terminal is equipped with a customer pole display, go to step 6; if not, go to
step 8.

6. Plug the CN17-0211-0001 adapter (supplied) into the ICIICISS45 interface cable socket
(if the ISS45 terminal is equipped with a customer pole display).

NOTE:

Both RJ-14 receptacles
in the ICI1000WK wiring kit (sup­plied with the ICI1000S) must be
connected at the black and yel­low terminals with 18 AWG two­conductor shielded cable (refer to
the ICI1000S manual).

ADAPTER ICIICISS45 ADAPTER

CUSTOMER POLE

DISPLAY CABLE

7. Plug the customer pole display (if equipped) cable connector into the CN17-0211-0001
adapter.

8. Plug the ICIICISS45 data cable RJ-14 connector into the DATA IN receptacle of the
ICI1000S video text inserter or into the ICI1000WK wiring kit receptacle.

9. Enable the customer pole display port if not previously being used.

10. Make certain all connections are tight. This completes the ICIICISS45 interface cable in­stallation. The ISS45 terminal must now be programmed by a qualified technician or
dealer for the following parameters: 9600 baud, 8 bits, and parity off.

TERMINAL

SW1

SWITCH

DATA CABLE TO ICI1000S

PORT 3

Figure 1. ICIICISS45 Inter-Check® Interface Cable

Programming

Inter-Check® must have communication parameters programmed in order to communicate with
the ISS45 terminal. Make certain the security CCTV equipment is correctly installed before
programming the system. Refer to the Inter-Check® ICI1000S Series installation/operation
manual for complete information about system programming and CCTV equipment installation.
Perform the following steps to program the Inter-Check® communication parameters:

1. Locate the NV switch beneath the ICI1000S video text inserter and position the switch
towards the BNC connectors.

2. Turn on power to the ICI1000S system.

3. Perform the following using the programming keypad on the ICI1000S video text inserter
(all menu items are displayed on the security monitor):

a. Enter the Main Menu programming mode by pressing ENT on the ICI1000S keypad.
b. Press 6, then press 8.
c. When the ICI1000S displays the message LOADED on the monitor, press the ESC

key .

d. After the ICI1000S reinitializes (monitor display reads SYSTEM INITIALIZED), press

the ENT key.
e. Press 1, then press 2.
f. Press the up arrow key twice (the up arrow key has a green dot beside it and is lo-

cated by the number 9 on the keypad).
g. Press the ESC key when the monitor display reads RS-232 STANDARD PRINTER.
h. Press the ESC key three times to reinitialize the ICI1000S (monitor display reads

SYSTEM INITIALIZED).

4. Locate the NV switch beneath the ICI1000S video text inserter and return it to its original
position away from the BNC connectors.

5. The Inter-Check® system is now programmed and ready to receive data from the ISS45
terminal.