Pelco HS6000 User Manual

®

HS6000 Series High-Security

Camera Enclosure

Installation/Operation Manual

C495M-D (12/96)

Pelco • 3500 Pelco Way, Clovis, CA 93612-5699 • USA • www.pelco.com

[phone] or (1-559) 292-1981 • FAX [phone] or (1-559) 292-3827

International Customers call (1-559) 292-1981 or FAX [phone]

TABLE OF CONTENTS

Section Page

1.0 WARNINGS .................................................................................................................................... 1

2.0 SCOPE ............................................................................................................................................2

3.0 DESCRIPTION ................................................................................................................................2

3.1 MODELS ............................................................................................................................... 2

4.0 INSTALLATION ...............................................................................................................................2

4.1 MOUNTING THE UNIT .........................................................................................................2

4.2 SPEAKER INSTALLATION ...................................................................................................3

4.3 OPTIONAL HB6000/HB6000/220/HB6024 HEATER/BLOWER KITS .................................. 3

4.4 ELECTRICAL CONNECTION ............................................................................................... 5

5.0 CARE AND MAINTENANCE ...........................................................................................................7

6.0 TAMPER SWITCH INSTALLATION ................................................................................................7

6.1 WIRING THE UNIT ................................................................................................................ 7

7.0 EXPLODED ASSEMBLY DIAGRAM ............................................................................................... 8

7.1 MECHANICAL PARTS LIST FOR HS6000 SERIES ENCLOSURE...................................... 8

8.0 SPECIFICATIONS ..........................................................................................................................9

9.0 WARRANTY AND RETURN INFORMATION ............................................................................... 10

LIST OF ILLUSTRATIONS

Figure Page

1 HB6000/HB6000/220/HB6024 Assembly ........................................................................................4

2 HB6000/220 Heater/Blower Kit Wiring Diagram (230 VAC) ............................................................ 5

3 HB6000 Heater/Blower Kit Wiring Diagram (120 VAC) ................................................................... 6

4 HB6024 Heater/Blower Kit Wiring Diagram (24 VAC) ..................................................................... 6

5 HS6000 Series Tamper Switch Installation .....................................................................................7

6 HS6000 Series Enclosure Exploded Assembly Diagram ................................................................ 8

7 HS6000 Dimension Drawing ...........................................................................................................9

REVISION HISTORY

Manual # Date Comments

C495M 5/90 Original manual.
C495M-A 9/95 Manual revised to include Tamper Switch Kit installation information.

Manual updated to new style.

C495M-B 11/95 Manual revised to include updated tamper switch/bracket part numbers

and exploded view diagram.

C495M-C 1/96 Revised to include tamper switch installation, specification description,

and new part numbers per ECO 95-397.

C495M-D 12/96 Revised Figure 6, Exploded Assembly Diagram and Section 7.1

Mechanical Parts List.

Pelco, the Pelco Logo, Camclosure, Esprit, Genex, Legacy, and Spectra are registered trademarks of Pelco. © Copyright 1996, Pelco. All rights reserved.
Endura and ExSite are trademarks of Pelco.

12 Pelco Manual C495M-D (12/96)

ii

INSTALLATION/OPERATION MANUAL
HS6000 SERIES HIGH-SECURITY
CAMERA ENCLOSURE

1.0 WARNINGS

Prior to installation and use of this product, the following
WARNINGS should be observed.

1. Installation and servicing should only be done by
Qualified Service Personnel and conform to all
Local codes.

2. Unless the unit is specifically marked as a NEMA
Type 3, 3R, 3S, 4, 4X, 6, or 6P enclosure, it is de­signed for indoor use only and it must not be in­stalled where exposed to rain and moisture.

3. Only use replacement parts recommended by
Pelco.

The product may bear the following
marks:

This symbol indicates that dangerous voltage
constituting a risk of electric shock is present

within this unit.

4. After replacement/repair of this unit’s electrical
components, conduct a resistance measurement
between line and exposed parts to verify the ex­posed parts have not been connected to line cir­cuitry.

5. The installation method and materials should be
capable of supporting four (4) times the weight of
the enclosure, pan/tilt, camera and lens combina­tion.

6. The camera and lens combination shall not exceed
40 lbs (18 kg).

This symbol indicates that there are important
operating and maintenance instructions in the

literature accompanying this unit.

CAUTION:

TO REDUCE THE RISK OF ELECTRICAL
SHOCK, DO NOT REMOVE COVER. NO
USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.

RISK OF ELECTRIC SHOCK.

CAUTION:

DO NOT OPEN.

Please thoroughly familiarize yourself with the information in this manual

prior to installation and operation.

Pelco Manual C495M-D (12/96) 1

2.0 SCOPE

The information within this manual covers the installa­tion of the HS6000 High Security Camera Enclosure.

3.0 DESCRIPTION

The HS6000 is a high security camera enclosure with
multiple camera capabilities designed for indoor “ceil­ing mount” installation for such applications as park­ing garages, hallways, prisons, detention cells, etc.,
requiring maximum protection from vandalism. De­signed to fit flush to the ceiling, the HS6000 comes
standard with two (2) of its four (4) window ports uti­lized. Optional windows or blank filler plates may be
ordered as needed. Provisions are made for mounting
a 4" speaker on the bottom of the enclosure. The win­dow ports provide adequate area for the installation
of infra-red illuminators.

Constructed of heavy gauge steel, the HS6000 will ac­cept most CCD cameras with fixed focal length lenses
ranging in size from 4 mm to 75 mm. For multi-camera
applications, camera/lens selection is critical and may
require the use of 2-piece cameras. There is no exposed
mounting hardware securing the HS6000 to its mount­ing surface. Opening the hinged access doors can only
be accomplished with a specially designed tool, elimi­nating the possibility of the enclosure being opened by
unauthorized personnel.

A factory-installed tamper switch provides added se­curity.

Optional accessories include a heater/blower kit in ei­ther 120 VAC, 230 VAC, or 24 VAC (HB6000, HB6000/
220, HB6024).

3.1 MODELS

HS6000 High security ceiling mount enclo-

sure designed to fit flush with the
ceiling. For use in applications such
as parking garages, hallways, prisons,
detention cells, etc., requiring maxi­mum protection from vandalism.
Multiple camera capabilities.

3.2 OPTIONS

HB6000 120 VAC thermostatically controlled

heater and blower. Heater provides
80 watts of heat and activates ON at
40°F; OFF at 60°F. blower provides
internal air circulation and activates
ON at 110°F; OFF at 80°F.

HB6000/220 Same as HB6000 except 230VAC

operation.

HB6024 Same as HB6000 except 24 VAC

operation.

HS600010018 Extra window

HS8000TT Tilt table assembly

4.0 INSTALLATION

Before installing the HS6000 to a ceiling, make certain
that the mounting surface is able to support the full
weight of the enclosure, plus the camera/lens and any
other options (i.e., speaker, IR illuminators, heater/
blower kits).

The lower portion of the enclosure can and should be
removed from the mounting plate to simplify installa­tion.

NOTE: The eight (8) fasteners required to
secure the HS6000 to a ceiling (minimum 3/8"
diameter recommended) are not supplied.

Provisions have been made to attach various
dual duplex conduit boxes to the mounting
plate. The electrical boxes are not supplied.

4.1 MOUNTING THE UNIT

To mount the enclosure to a ceiling, perform the fol­lowing steps:

1. Open the two (2) access doors by removing four
(4) (two [2] each door) 1/4-20 “Tampruf” screws.
A special socket is provided (fits 1/4" square drive).
The doors hinge down.

2. Using the mounting plate as a template, mark and
drill holes in the mounting surface.

NOTE: The removal of eight (8) 1/4-20
“Tampruf” screws around the perimeter of the
mounting plate will separate it from the rest of
the enclosure.

3. Attach the enclosure (mounting plate) with the re­quired fasteners.

4. Route the required cables through the knockouts.

2 Pelco Manual C495M-D (12/96)

5. Mount the camera/lens to the ball swivel provided.

NOTE: An optional tilt table assembly
(HS8000TT) may be used instead.

If removed, replace lower portion of enclosure.

6. Make all appropriate connections (i.e., camera
power, video (coax), lens, speaker, IR illuminator,
heater/blower kits).

4.3 OPTIONAL HB6000, HB6000/220,
HB6024 HEATER/BLOWER KITS

The HB6000, HB6000/220, and HB6024 heater/blower
kits require 120 VAC, 230 VAC, or 24 VAC respectively.
They provide 80 watts of heat which is thermostati­cally controlled to turn ON at 40°F (4.44° C) and turn
OFF at 60°F (15.56° C). They also provide internal air
circulation which is thermostatically controlled to turn
on at 110°F (43.44° C) and OFF at 80°F (26.67° C).

7. Position the camera and tighten the ball swivel outer
collar to secure.

8. Close the access doors and check that all compo­nents clear. Secure the doors with the four (4) (two
[2] per door) 1/4-20 “Tampruf” screws provided.

4.2 SPEAKER INSTALLATION

The HS6000 provides a position for mounting a small
speaker (3" x 3" bolt pattern) to be provided by the user.

The speaker grill is shipped with a cover plate mounted
over it on the inside. This plate must be removed prior
to speaker installation.

Model Input Voltage Power Consumption Cable Size Cable Distance

4.3.1 Recommended Cable Size

CAUTION: When using a single power

source for both the camera and accessories, the
camera power consumption must be taken into
consideration when determining the wire gauge.

The following cable sizes are the minimum recom­mended for use with the combination of blower/heater/
camera.

HB6000 120 VAC 90 watts 22 Awg 464.7 ft (141.9 m)

20 Awg 738.9 ft (225.2 m)
18 Awg 1,175.5 ft (358.3 m)
16 Awg 1,865.7 ft (568.7 m)

HB6000/220 230 VAC 90 watts 24 Awg 1,047.4 ft (319.3 m)

22 Awg 1,666.0 ft (507.8 m)
20 Awg 2,649.2 ft (807.5 m)
18 Awg 4,214.6 ft (1,284.6 m)
16 Awg 6,688.8 ft (2,038.8 m)

HB6024 24 VAC 90 watts 20 Awg 31.5 ft (9.6 m)

18 Awg 50.2 ft (15.3 m)
16 Awg 79.6 ft (24.3 m)
14 Awg 127.0 ft (38.7 m)

Pelco Manual C495M-D (12/96) 3

4.3.2 Heater/Blower Kit Installation

4.3.2.2 Blower/PCB Assembly

To install the HB6000, HB6000/220, HB6024, perform
the following steps (refer to Figure 1).

4.3.2.1 Heater Assembly

1. Open an access door (both if needed).

2. The heater bracket is designed to attach to two (2)
adjacent studs retaining the window.

3. Remove any two (2) adjacent nuts and washers on
both sides of the window.

4. Place the heater brackets on the studs, heaters
angled away from the window, and replace and
tighten the hardware.

1. Open an access door (both if needed).

2. On the HS6000, the blower/PCB bracket is de­signed to attach to the two (2) studs at the bottom
of the window.

3. Remove the nuts and washers retaining the bottom
of the window.

4. Place the blower/PCB bracket over the studs and
replace and tighten the hardware.

Figure 1. HB6000, HB6000/220, HB6024 Assembly

4 Pelco Manual C495M-D (12/96)

4.3.2.3 Heater/Blower Wiring

4.4 ELECTRICAL CONNECTION

The blower is factory wired to the PCB assembly. Con­nect the heaters to the PCB assembly as shown in the
respective wiring diagrams (Figure 2, Figure 3, or Fig­ure 4). Supply AC line voltage (230 VAC, 120 VAC, or
24 VAC) as shown.

After the cable has been routed, all wire connections
should be made (i.e., video, lens, camera power, heat­ers).

CAUTION: When a single power source is
used for both the camera and accessories, the
camera power consumption must be taken into
consideration when determining the wire gauge.
Also, make certain that all electrical connec­tions are done properly and meet electrical
codes.

Figure 2. HB6000/220 Heater/Blower Kit Wiring Diagram (230 VAC)

Pelco Manual C495M-D (12/96) 5

Figure 3. HB6000 Heater/Blower Kit Wiring Diagram (120 VAC)

Figure 4. HB6024 Heater/Blower Kit Wiring Diagram (24 VAC)

6 Pelco Manual C495M-D (12/96)

5.0 CARE AND MAINTENANCE

Maintenance performed at regularly scheduled inter­vals will help prolong the operational life and appear­ance of the equipment.

1. Clean the Lexan window with a mild non-abrasive
detergent in water and a soft cloth regularly to help
maintain picture clarity. For a heavily soiled win­dow, use vinyl cleaner.

To install a replacement tamper switch, refer to Figure
5 for the correct position of the bracket/switch and per­form the following steps:

1. Remove the screws securing the access door of the
desired “alarmed” opening.

2. Install the bracket so that the mounting studs go
through the slots in the bracket.

NOTE: Pelco offers a 24-hour, seven-day-a
week Technical Assistance Program (TAP) de­signed to assist any customer with a technical
problem involving Pelco equipment whether it’s
the weekend or late at night. For technical as­sistance dial [phone] and you will be
connected to a Pelco TAP member who is
trained to answer your questions.

Pelco also guarantees one-day turnaround on
any Pelco equipment sent in for repair. This
includes warranty and non-warranty items.
Refer to the section on “Warranty and Return
Information” in this manual for the proper pro­cedure.

6.0 TAMPER SWITCH INSTALLATION

The HS6000 enclosures come standard from the fac­tory with a tamper switch(es) mounted on the secured
access door. Refer to Section 6.1 for wiring.

NOTE: The slot in the bracket allows the switch

to be used against either the 1/2” thick lexan win­dow or the .134” thick metal plate.

3. If the switch is to be used against the metal plate,
slide the bracket so that the studs are at the end of
the slot that is furthest from the switch plunger.

4. If the switch is to be used against the Lexan win­dow, slide the bracket so that the studs are at the
end of the slot nearest the switch plunger.

5. Secure the bracket/switch with lockwashers and
nuts.

6.1 WIRING THE UNIT

The tamper switch comes with both a “Normally Open”
contact and a “Normally Closed” contact.

For a “Normally Open” circuit, use the “open” and
“common” terminals; for a “Normally Closed” circuit,
use the “closed” and “common” terminals.

Figure 5. HS6000 Series Tamper Switch Installation

Pelco Manual C495M-D (12/96) 7

7.0 EXPLODED ASSEMBLY DIAGRAM

Figure 6. HS6000 Series Enclosure Exploded Assembly Diagram

7.1 MECHANICAL PARTS LIST FOR HS6000 SERIES ENCLOSURE

Item No. Qty Description Part Number

12Window, Lexan, 6" x 1" x .50", Clear HS600010018
21Plate, Top/Mounting HS60004001COMP
32Plate, Side HS60004003COMP
42Plate, Access Door HS60004004COMP
52Plate, Blank/Filler HS60004018COMP
62Hinge HS60004007COMP
71Plate, Bottom/Hinge HS60004009COMP
84NP TPE, Acry Foam, Y-4930, 1" 2592IN/RL ZHTAPE1.0X.025

91Socket, Tampruf #10, 1/4" Drive ZTSOCKET10
10 1 Plate, Grill, Block-Off HS80004115COMP
11 2 Switch, Tamper SWI1DM401
12 2 Bracket, Switch, Break-In HS60004113COMP
13 2 Camera Pad CM1700120007
14 2 Camera Mounting Nut CM17504004COMP
15 2 Ball Stud CM17504003COMP
16 2 Ball Stud Sleeve CM17504002COMP
17 2 Ball Anvil CM17504005COMP

8 Pelco Manual C495M-D (12/96)

8.0 SPECIFICATIONS

ELECTRICAL

MECHANICAL

Window: 1/2" (1.27 cm) thick impact and abra-

sion resistant Lexan

Camera
Mounting: Adjustable tilt table and/or ball

swivel

Maximum
Camera/Lens
Size: Accepts camera/lens combinations

up to 8.0" L x 4.0" W x 4.0" H
(20.32 cm x 10.16 cm x 10.16 cm)

Enclosure
Mounting: Eight (8) .390" (0.99 cm) diameter

holes on protected mounting plate

Security: Tamper-resistant screws N.O./N.C.

switch contact on covers

Tamper Switch: Plunger type door switch with “pull

to cheat” feature. N.O./N.C. contacts
clearly marked on body of switch.
DM electrical rating: 10A, 125V.
Plunger type with .20" (0.51 cm)

Cable Entry: Access through top; accepts 4"

(10.16 cm) electrical box
Four (4) 1/2"-3/4" (1.27-1.90 cm)
knockouts

Tamper Switch: 1/4" (.63 cm) quick connect. N.O./

N.C. clearly marked on switch body.
10A, maximum switching current
125V, maximum switching voltage.

GENERAL

Construction: Formed 10 gauge .134" (0.34 cm)

steel

Finish: Polyester powder coat

Dimensions: See Figure 7

Environment: Indoor

Unit Weight: 46 lbs, 6 ozs (20.87 kg)

Product specifications subject to change without notice.

Figure 7. HS6000 Dimension Drawing

Pelco Manual C495M-D (12/96) 9

9.0 WARRANTY AND RETURN
INFORMATION

WARRANTY

Pelco will repair or replace, without charge, any merchandise proved
defective in material or workmanship for a period of one year after the date
of shipment.

Exceptions to this warranty are as noted below:

• Five years on FT/FR8000 Series fiber optic products.

• Three years on Genex

keyboard).

• Three years on Camclosure® and fixed camera models, except the

CC3701H-2, CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2,
and MC3651H-2X camera models, which have a five-year warranty.

• Two years on standard motorized or fixed focal length lenses.

• Two years on Legacy®, CM6700/CM6800/CM9700 Series matrix, and

DF5/DF8 Series fixed dome products.

• Two years on Spectra®, Esprit®, ExSite™, and PS20 scanners, includ-

ing when used in continuous motion applications.

• Two years on Esprit

wiper blades).

• Eighteen months on DX Series digital video recorders, NVR300

Series network video recorders, and Endura
network-based video products.

• One year (except video heads) on video cassette recorders (VCRs).

Video heads will be covered for a period of six months.

• Six months on all pan and tilts, scanners or preset lenses used in

continuous motion applications (that is, preset scan, tour and auto scan
modes).

Pelco will warrant all replacement parts and repairs for 90 days from the
date of Pelco shipment. All goods requiring warranty repair shall be sent
freight prepaid to Pelco, Clovis, California. Repairs made necessary by
reason of misuse, alteration, normal wear, or accident are not covered
under this warranty.

Pelco assumes no risk and shall be subject to no liability for damages or
loss resulting from the specific use or application made of the Products.
Pelco’s liability for any claim, whether based on breach of contract,
negligence, infringement of any rights of any party or product liability,
relating to the Products shall not exceed the price paid by the Dealer to
Pelco for such Products. In no event will Pelco be liable for any special,
incidental or consequential damages (including loss of use, loss of profit
and claims of third parties) however caused, whether by the negligence
of Pelco or otherwise.

The above warranty provides the Dealer with specific legal rights. The
Dealer may also have additional rights, which are subject to variation from
state to state.
If a warranty repair is required, the Dealer must contact Pelco at (800)
289-9100 or [phone] to obtain a Repair Authorization number
(RA), and provide the following information:

1. Model and serial number

2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice

number

3. Details of the defect or problem If there is a dispute regarding the

warranty of a product which does not fall under the warranty conditions
stated above, please include a written explanation with the product
when returned.

Method of return shipment shall be the same or equal to the method by
which the item was received by Pelco.

®

Series products (multiplexers, server, and

®

and WW5700 Series window wiper (excluding

™

Series distributed

RETURNS

In order to expedite parts returned to the factory for repair or credit, please
call the factory at [phone] or [phone] to obtain an
authorization number (CA number if returned for credit, and RA number
if returned for repair).

All merchandise returned for credit may be subject to a 20% restocking
and refurbishing charge.

Goods returned for repair or credit should be clearly identified with the
assigned CA or RA number and freight should be prepaid. Ship to the
appropriate address below.

If you are located within the continental U.S., Alaska, Hawaii or Puerto
Rico, send goods to:

Service Department
Pelco
3500 Pelco Way
Clovis, CA 93612-5699

If you are located outside the continental U.S., Alaska, Hawaii or Puerto
Rico and are instructed to return goods to the USA, you may do one of the
following:

If the goods are to be sent by a COURIER SERVICE, send the goods to:

Pelco
3500 Pelco Way
Clovis, CA 93612-5699 USA

If the goods are to be sent by a FREIGHT FORWARDER, send the goods
to:

Pelco c/o Expeditors
473 Eccles Avenue
South San Francisco, CA 94080 USA
Phone: [phone]
Fax: [phone]

This equipment contains electrical or electronic components that must be recycled properly to comply with Directive 2002/96/EC of the European Union
regarding the disposal of waste electrical and electronic equipment (WEEE). Contact your local dealer for procedures for recycling this equipment.

10 Pelco Manual C495M-D (12/96)