®
HS2000 Series
High Security Enclosures
Installation/Operation Manual
C494M-D (1/96)
Pelco • 300 W. Pontiac Way, Clovis, CA 93612-5699 • USA • (800) 289-9100 or (1-559) 292-1981
FAX (800) 289-9150 or (1-559) 292-3827 • DataFAX (800) 289-9108 or (1-559) 292-0435
TABLE OF CONTENTS
Section Page
1.0 WARNINGS.....................................................................................................................................1
2.0 SCOPE............................................................................................................................................2
3.0 DESCRIPTION................................................................................................................................2
3.1 MODELS ...............................................................................................................................2
3.2 OPTIONS ..............................................................................................................................2
4.0 INSTALLATION ...............................................................................................................................3
4.1 CEILING MOUNTING (FLUSH) ............................................................................................3
4.2 MID-WALL MOUNTING ........................................................................................................3
4.3 WINDOW INSTALLATION.....................................................................................................3
4.4 TAMPER SWITCH INSTALLATION ......................................................................................4
4.5 TAMPER SWITCH WIRING..................................................................................................4
5.0 CARE AND MAINTENANCE ..........................................................................................................4
6.0 EXPLODED ASSEMBL Y DIAGRAM ...............................................................................................7
7.0 MECHANICAL PARTS LIST FOR HS2000 ENCLOSURE..............................................................7
8.0 SPECIFICATIONS...........................................................................................................................8
9.0 WARRANTY AND RETURN INFORMATION .................................................................................9
LIST OF ILLUSTRATIONS
Figure Page
1 HS2000 Series Tamper Switch Installation .....................................................................................4
2 HS2000 Exploded Assembly Diagram ............................................................................................7
3 HS2000 Dimension Drawing ...........................................................................................................8
REVISION HISTORY
Manual # Date Comments
C494M 5/90 Original version.
C494M 9/93 Rev. A. Put into two-column format. Exploded assembly diagram and
parts list updated.
C494M-B 9/95 Rev. B. Revised to include wiring instructions for tamper switch and put
into new two-column format.
C494M-C 11/95 Rev. C. Revised to include updated tamper switch/bracket part numbers
and exploded view diagram.
C494M-D 1/96 Rev. D. Revised to include tamper switch installation, specification
description and new part numbers per ECO 95-397.
4/96 Revised Section 7.0, item no. 1 to part number HS10004313COMP.
®Pelco and the Pelco logo are registered trademarks of Pelco.
©Copyright 1996, Pelco. All rights reserved.
12 Pelco Manual C494M-D (1/96)
ii
INSTALLATION/OPERATION MANUAL
HS2000 SERIES
HIGH SECURITY ENCLOSURE
1.0 WARNINGS
Prior to installation and use of this product, the following
WARNINGS should be observed.
1. Installation and servicing should only be done by
Qualified Service Personnel and conform to all
Local codes.
2. Unless the unit is specifically marked as a NEMA
T ype 3, 3R, 3S, 4, 4X, 6, or 6P enclosure, it is designed for indoor use only and it must not be installed where exposed to rain and moisture.
3. Only use replacement parts recommended by
Pelco.
The product may bear the following
marks:
This symbol indicates that dangerous voltage
constituting a risk of electric shock is present
within this unit.
4. The camera and lens combination shall not exceed
20 lbs (9.06 kg).
5. The installation method and materials should be
capable of supporting four (4) times the weight of
the enclosure, pan/tilt, camera and lens combination.
This symbol indicates that there are important
operating and maintenance instructions in the
literature accompanying this unit.
CAUTION:
TO REDUCE THE RISK OF ELECTRICAL
SHOCK, DO NOT REMOVE COVER. NO
USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
RISK OF ELECTRIC SHOCK.
CAUTION:
DO NOT OPEN.
Please thoroughly familiarize yourself with the information in this manual
prior to installation and operation.
Pelco Manual C494M-D (1/96) 1
2.0 SCOPE
3.1 MODELS
The information within this manual covers the installation of the HS2000 High Security Camera Enclosure.
3.0 DESCRIPTION
The HS2000 high security camera enclosure is designed
for indoor “corner mount” installation for such applications as elevators, parking garages, classrooms, offices, detention cells, etc., requiring maximum protection from vandalism in an unobtrusive package. Designed to fit flush to the ceiling in a corner, an optional
hood (HS2000H) allows the HS2000 to be mounted
lower on the wall and still retain the enclosure’s integrity. An impact-resistant clear Lexan window is supplied, an optional smoked window is available.
Constructed of medium gauge steel, the HS2000 will
accept many of the smaller CCD cameras with fixed
focal length and auto-iris lenses. There is no exposed
mounting hardware securing the HS2000 to its mounting surface. Opening the enclosure can only be accomplished by removing the tamper-resistant screw from
the bottom. In addition, a factory-installed tamper
switch is mounted on the secured access cover.
HS2000 High security corner mount enclo-
sure designed to fit flush with the
ceiling. For use in applications
such as elevators, parking garages,
classrooms, offices, detention
cells, etc., requiring maximum protection from vandalism in an unobtrusive package.
HS2000/BR Same as HS2000 except brass
plated finish.
HS2000/CH Same as HS2000 except chrome
plated finish.
3.2 OPTIONS
HS2000H Hood for mid-wall mounting of
HS2000 enclosure.
HS200010019 Smoked window, 1/4" (6.35 mm)
thick, impact and abrasion-resistant Lexan.
2 Pelco Manual C494M-D (1/96)
4.0 INSTALLATION
4.2 MID-WALL MOUNTING
Before installing the HS2000 to a wall, make certain
that the mounting surface is able to support the full
weight of the enclosure plus the camera and lens.
The tilt table and tilt table mounting brackets may be
removed to provide adequate clearance for mounting
the enclosure.
NOTE: The four (4) fasteners required to secure the HS2000 to a wall (minimum 3/8" diameter recommended) are not supplied.
4.1 CEILING MOUNTING (FLUSH)
To mount the enclosure to a wall (tight to the ceiling),
perform the following steps:
1. Remove the cover from the mounting bracket. A
special socket is provided (fits 1/4" square drive).
2. Using the mounting bracket or the template provided, mark and drill holes in the mounting surface.
3. Attach the enclosure with the required fasteners.
T o mount the HS2000 enclosure mid-wall, use the optional hood, HS2000H, and perform the following steps:
1. Determine the position for the hood. Using it as a
template, mark and drill holes in the mounting surface.
2. Attach the hood with the required fasteners (minimum 3/8" diameter recommended).
3. Continue with steps 1-8 in Section 4.1.
4.3 WINDOW INSTALLATION
The HS2000 is provided with a clear Lexan 1/4" thick
viewing window. An optional smoked window,
HS200010019, is available.
Instructions for installing the optional smoked window
are as follows:
1. Remove the cover from the mounting bracket. A
special socket is provided.
2. Remove the four (4) 1/4-20 elastic locknuts and
1/4" flat washers.
4. Route the required cables through the back or top.
5. Mount the camera/lens to the tilt table.
6. Make all appropriate connections (i.e., camera
power, video (coax), lens).
7. Position the camera and tighten the 1/4-20 fasteners to secure the tilt table in place.
8. Replace the cover and check that all components
clear. Secure with the 1/4-20 “T ampruf” screw provided.
NOTE: A plate is provided to prevent access
through the top of this enclosure. If needed, it
is mounted with the mounting bracket using the
same mounting holes and hardware.
3. Remove the window.
4. Remove the protective coatings from the new window and place the window over the four (4) 1/4-20
studs.
5. Replace the hardware and replace the cover.
Pelco Manual C494M-D (1/96) 3
4.4 TAMPER SWITCH INSTALLATION
5.0 CARE AND MAINTENANCE
The HS2000 enclosures come standard from the factory with a tamper switch installed. Should it become
necessary to install a replacement switch, refer to Figure 1 for the correct position of the bracket/switch and
perform the following steps:
1. Remove the front cover.
2. Install the bracket/switch and secure with
lockwashers and nuts.
4.5 TAMPER SWITCH WIRING
The tamper switch comes with both a “Normally Open”
and a “Normally Closed” contact.
For a “Normally Open” circuit, use the “open” and
“common” terminals; for a “Normally Closed” circuit,
use the “closed” and “common” terminals.
Maintenance performed at regularly scheduled intervals will help prolong the operational life and appearance of the equipment.
1. Clean the Lexan window with a mild non-abrasive detergent in water and a soft cloth regularly to
help maintain picture clarity. For a heavily soiled
window, use vinyl cleaner.
NOTE: Pelco offers a 24-hour, seven-day-a
week T echnical Assistance Program (T AP) designed to assist any customer with a technical
problem involving Pelco equipment whether it’s
the weekend or late at night. For technical assistance dial (800) 289-9100 and you will be
connected to a Pelco TAP member who is
trained to answer your questions.
Pelco also guarantees one-day turnaround on
any Pelco equipment sent in for repair. This
includes warranty and non-warranty items.
Refer to the section on “Warranty and Return
Information” in this manual for the proper procedure.
Figure 1. HS2000 Series Tamper Switch Installation
4 Pelco Manual C494M-D (1/96)
HS2000 Mounting Template
Pelco Manual C494M-D (1/96) 5
(This page intentionally left blank.)
6 Pelco Manual C494M-D (1/96)
6.0 EXPLODED ASSEMBLY DIAGRAM
Figure 2. HS2000 Exploded Assembly Diagram
7.0 MECHANICAL PARTS LIST FOR HS2000 ENCLOSURE
Item No. Qty Description Part Number
1 1 Bracket, Switch, Break-In HS10004313COMP
2 1 Window, 8" x 7" x .25" Drilled MR5 Clear Lexan HS200010009
3 1 Plate, Mounting HS20004001COMP
4 1 Cover, Front, Beige HS20004003COMP
Cover, Front, Brass Plated HS20004003BRCMP
Cover, Front, Chrome Plated HS20004003CHCMP
5 1 Tilt Table HS20004007COMP
6 1 Cover, Top, Corner Mount HS20004023COMP
7 1 Bracket, Mount, Tilt Table, Left HS20004115COMP
8 1 Bracket, Mount, Tilt Table, Right HS20004215COMP
9 1 Switch, Tamper SWI1DM401
A 2 Screw, 1/4-20 x 1/2", Round, Tampruf #10, SS ZH1/4-20X.50SRT
B 1 Screw, 1/4-20 x 3/4", Round, Tampruf #10, SS ZH1/4-20X.75SRT
C 2 Tape, Two-Sided, Acrylic x inch ZHTAPE1.00X.025
D 2 Bolt, 1/4-20 x 5/8" Hex Head C/S SS ZH1/420X.625CH
E 2 Nut, Hex, 1/4-20, SS ZH1/4-20NUTCH
F 4 Washer, Split Lock, 1/4" SS ZH1/4LWSSL
G 7 Washer, Flat 3/16" Special, SS ZH260X562X65C
H 4 Washer, Flat 15/16", SS ZH932X1.75X130
I 4 Nut, Lock 1/4-20 Nylon Insert, SS ZH1/420NUTCHN
J 1 Socket, Tampruf #10, 1/4" Drive (not shown) ZTSOCKET10
Pelco Manual C494M-D (1/96) 7
8.0 SPECIFICATIONS
MECHANICAL
Window: 1/4" (6.35 mm) thick impact and
abrasion resistant clear Lexan
Camera Mounting: Adjustable tilt table
Maximum
Camera/Lens Size: Accepts camera/lens combina-
tions (including BNC connector)
up to:
3.0" H x 3.0" W x 6.0" L
(7.62 cm x 7.62 cm x 15.24 cm)
Enclosure Mounting: Four (4) .390" (0.99 cm) diam-
eter holes on protected rear surface
Security: Tamper-resistant screw N.O./
N.C. switch contact on cover
Tamper Switch: Plunger type door switch with
“pull to cheat” feature. N.O./
N.C. contacts clearly marked on
body of switch. DM electrical
rating: 10A, 125V. Plunger type
with .20" (0.51 cm)
ELECTRICAL
Cable Entry: Access through back and top
Tamper Switch: 1/4" (.63 cm) quick connect. N.O./
N.C. clearly marked on switch body.
10A, maximum switching current
125V, maximum switching voltage.
GENERAL
Construction: Formed 14 gauge .074" (0.19 cm)
steel
Finish: Poly vinyl powder coat
Dimensions: See Figure 3
Environment: Indoor
32° to 120° F (0° to 48.89° C)
Unit Weight: 6 lbs 6 oz (2.72 kg)
Figure 3. HS2000 Dimension Drawing
8 Pelco Manual C494M-D (1/96)
9.0 WARRANTY AND RETURN
INFORMATION
WARRANTY
Pelco will repair or replace, without charge, any
merchandise proved defective in material or
workmanship for a period of one (1) year after the date
of shipment.
• Six (6) months on all pan and tilts, scanners or
preset lenses used in continuous motion
applications (e.g., preset scan, tour and auto scan
modes).
• Two (2) years on Legacy®, Intercept® and CM8500/
CM9500/CM9750 Matrix products.
• Two (2) years on WW5700 series window wiper
(excluding wiper blades).
Pelco will warranty all replacement parts and repairs
for 90 days from the date of shipment. All goods for
warranty work shall be sent freight prepaid to our
Clovis, California facility. Repairs made necessary by
reason of misuse, alteration, normal wear, or accident
are not covered under this warranty. Pelco is not liable
for any incidental or consequential expenses or liability
incurred by the customer as a result of field repair,
installation, or any other reason.
If there is a dispute regarding the warranty of a product
which does not fall under the warranty conditions
stated above, please include a written explanation with
the product when returned.
Ship freight prepaid to: Pelco
300 West Pontiac Way
Clovis, CA 93612-5699
Method of return shipment shall be the same as method
by which the repair item is received by Pelco.
RETURNS
In order to expedite parts returned to the factory for
repair or credit, please call the factory at (800) 289-
9100 or (559) 292-1981 to obtain an authorization
number (CA number if returned for credit, and RA
number if returned for repair). Goods returned for
repair or credit should be clearly identified with the
assigned CA/RA number and freight should be prepaid.
All merchandise returned for credit may be subject to
a 20% restocking and refurbishing charge.
Ship freight prepaid to: Pelco
300 West Pontiac Way
Clovis, CA 93612-5699
The above warranty is in lieu of any other expressed or
implied warranty, condition, or guarantee by Pelco of
the equipment listed herein. Pelco makes no warranties
except for intended use and will not be liable for any
loss, damage, or costs arising, whether consequential
or incidental, from the use of said merchandise.
This warranty gives you specific legal rights. You may
also have additional rights, which are subject to variation
from state to state.
If a warranty repair is required, contact Pelco at (800)
289-9100 or (559) 292-1981 for a Repair
Authorization number (RA), and provide the following
information:
1. Model and serial number
2. Date of shipment, P.O. number, Sales Order
number, or Pelco invoice number
3. Details of the defect or problem
Pelco Manual C494M-D (1/96) 9
®
Pelco
300 West Pontiac Way
Clovis, CA 93612-5699 USA
(559) 292-1981 • (800) 289-9100
FAX (800) 289-9150 or (559) 292-3827 DataFAX (800) 289-9108 or (559) 292-0435
International customers call 1-559-292-1981 or FAX 1-559-348-1120
(Product specifications subject to change without notice.)
C494M-D
10 Pelco Manual C494M-D (1/96)
Loading...