Pelco HKHS3024 User Manual

®

HKHS3000/HKHS3024

Heater Kits

Installation/Operation

Manual C499M

1.0 SCOPE

The information contained within this manual covers
the HKHS3000 and HKHS3024 heater kits.

Installation should be in accordance with all applicable
local and national electric codes, utilizing approved
materials only.

Please thoroughly familiarize yourself with the infor­mation in this manual prior to installation and opera­tion.

2.0 DESCRIPTION

The HKHS3000 (120 VAC) and HKHS3024 (24 VAC)
are field installed heater kits for the HS3000 and
HS3020 high security enclosures.

These heater kits provide 30 watts of heat and are ther­mostatically controlled ON at 40°F (4.44°C) and OFF
at 60°F (15.56°C).

2.1 RECOMMENDED CABLE DIST ANCES

The following are the recommended cable distances for
heater operation when used with a transformer capable
of delivering the power requirements. Cable distances
are based on a 10% line loss.

120 VAC 24 VAC

(at 30 watts) (at 30 watts)

16 Awg 5,970 feet (1,820 m) 240 feet (73 m)
18 Awg 3,760 feet (1,146 m) 150 feet (46 m)
20 Awg 2,365 feet (721 m) 95 feet (29 m)

PELCO • 300 W. Pontiac Way, Clovis, CA 93612-5699 • [phone] • [phone]

FAX [phone] or [phone] • DataFAX [phone] or [phone]

3.0 INSTALLATION

T o install the HKHS3000 and HKHS3024, perform the
following steps.

1. Remove the cover from the enclosure.

2. Attach the PC board/bracket assembly to the rear
plate using two (2) 1/4-20 nuts and lock washers,
attaching to the studs on the end plate (see Figures
1 and 3).

3. Install the heater pads onto the front of the body
(end nearest window) by removing the backing and
pressing in place onto the floor of enclosure (see
Figure 3).

4. Wire per the wiring diagram in Figure 2.

Figure 1. Heater Kit Installation

Figure 2. HKHS3000 and HKHS3024 Wiring Diagram

2 Pelco Manual C499M

4.0 EXPLODED ASSEMBLY DIAGRAM

Figure 3. HKHS3000/HKHS3024 Exploded Assembly Diagram

5.0 MECHANICAL PARTS LIST

The following parts list corresponds to the items identified in Figure 3 above.

Item

Number Quantity Description Part Number

1 2 Heater blanket, 120 VAC, 15 watts (HKHS3000) HK300010115

Heater blanket, 24 VAC, 15 watts (HKHS3024) HK300010024

2. 1 Bracket, PCB HSK30004000COMP

3 1 PCB assembly, term/thermostat PCB9000300ASSY

A 2 Nut, hex 1/40-20 XX ZH1/4-20NUTCH

B 2 Washer, #5610-22-60, nylon ZH200X437X62N

C 2 Screw, 4-40 x 3/8" pan Phillips, SS ZH4-40X.375SPP

Pelco Manual C499M 3

6.0 WARRANTY AND RETURN
INFORMATION

WARRANTY

Pelco will repair or replace, without charge, any
merchandise proved defective in material or
workmanship for a period of one (1) year after the date
of shipment. Exceptions to this warranty are as noted
below:

• Six (6) months on all pan and tilts, scanners or
preset lenses used in continuous motion
applications (e.g., preset scan, tour and auto scan
modes).

• Two (2) years on Legacy®, Intercept® and CM8500/
CM9500/CM9750 Matrix products.

• Two (2) years on WW5700 series window wiper
(excluding wiper blades).

Pelco will warranty all replacement parts and repairs
for 90 days from the date of shipment. All goods for
warranty work shall be sent freight prepaid to our
Clovis, California facility. Repairs made necessary by
reason of misuse, alteration, normal wear, or accident
are not covered under this warranty. Pelco is not liable
for any incidental or consequential expenses or liability
incurred by the customer as a result of field repair,
installation, or any other reason.

If there is a dispute regarding the warranty of a product
which does not fall under the warranty conditions
stated above, please include a written explanation with
the product when returned.

Ship freight prepaid to: Pelco

300 West Pontiac Way
Clovis, CA 93612-5699

Method of return shipment shall be the same as method
by which the repair item is received by Pelco.

RETURNS

In order to expedite parts returned to the factory for
repair or credit, please call the factory at (800) 289-
9100 or [phone] to obtain an authorization
number (CA number if returned for credit, and RA
number if returned for repair). Goods returned for
repair or credit should be clearly identified with the
assigned CA/RA number and freight should be prepaid.
All merchandise returned for credit may be subject to
a 20% restocking and refurbishing charge.

Ship freight prepaid to: Pelco

300 West Pontiac Way
Clovis, CA 93612-5699

The above warranty is in lieu of any other expressed or
implied warranty, condition, or guarantee by Pelco of
the equipment listed herein. Pelco makes no warranties
except for intended use and will not be liable for any
loss, damage, or costs arising, whether consequential
or incidental, from the use of said merchandise.

®

This warranty gives you specific legal rights. You may
also have additional rights, which are subject to variation
from state to state.

Pelco

300 West Pontiac Way, Clovis, CA 93612-5699

If a warranty repair is required, contact Pelco at (800)
289-9100 or [phone] for a Repair

Authorization number (RA), and provide the following

[phone] • [phone]

FAX [phone] or [phone] •

DataFAX [phone] or [phone]

information:

International customers call 1-559-292-1981 or

1. Model and serial number

FAX [phone]

2. Date of shipment, P.O. number, Sales Order

number, or Pelco invoice number

3. Details of the defect or problem

(Product specifications subject to change

without notice.)

C499M

4 Pelco Manual C499M