Pelco HK700 User Manual

Download

Page 1

C2412M (11/99) BK700 Series Blower Kit HK700 Series Heater Kit

3500 Pelco Way Clovis, CA 93612-5699 USA

In North America & Canada: Tel (800) 289-9100 FAX (800) 289-9150

International Customers: Tel +1 (559) 292-1981 FAX +1 (559) 348-1120

www.pelco.com

IMPORTANT SAFEGUARDS AND WARNINGS

Prior to installation and use of this product, the following WARNINGS should be observed.

1. Installation and servicing should only be done by qualified service personnel and conform to all local codes.

2. Unless the unit is specifically marked as a NEMA Type 3, 3R, 3S, 4, 4X ,6 or 6P enclosure, it is designed for indoor use only and it must not be installed where exposed to rain and moisture.

3. Only use replacement parts recommended by Pelco.

4. After replacement/repair of this unit’s electrical components, conduct a resistance measurement between line and exposed parts to verify the exposed parts have not been connected to line circuitry.

Please thoroughly familiarize yourself with the information in this manual prior to installation and operation.

MODELS

Blower Kits

BK700 For use with E706 or E708 Series Enclosure, 120 VAC, 60 Hz, 4 watts,

10 cfm internal air circulation

BK700/220 Same as BK700 except 230 VAC, 50 Hz, 9 watts, 8 cfm internal air

circulation

BK700/24 Same as BK700 except 24 VAC, 3 watts, 19 cfm of internal air circulation

Heater Kits

HK706-1 Thermostatically controlled, 120 VAC, 80 watts, for E706 Series Enclosure

only. Activates ON at 40°F (4°C) and OFF at 60°F (16°C) HK706-2 Same as HK706-1 except 24 VAC HK706-3 Same as HK706-1 except 230 VAC HK708/10-1 Thermostatically controlled, 120 VAC, 107 watts, for E708 Series

Enclosure only. Activates ON at 40°F (4°C) and OFF at 60°F (16°C) HK708/10-2 Same as HK708/10-1 except 24 VAC, 66 watts HK708/10-3 Same as HK708/10-1 except 230 VAC, 84 watts

INSTALLATION

CAUTION:

When a single power source is used for both the camera and accessories, the camera power consumption must be taken into consideration when determining the wire gauge. However, the following chart does not include camera power because of the many variations.

Table A. Power Requirements and Recommended Cable Sizes

Model Number Input Voltage Power Consumption Cable Size Cable Distance

BK700 120 VAC 4 watts 22 AWG 10,651 feet (3,246 m)

BK700/24 24 VAC 3 watts 20 AWG 914 feet (279 m)

20 AWG 17,143 feet (5,225 m) 18 AWG 27,108 feet (8,262 m) 16 AWG 43,062 feet (13,125 m)

18 AWG 1,446 feet (441 m) 16 AWG 2,297 feet (700 m) 14 AWG 3,650 feet (1,113 m)

Continued on next page

Page 2

Table A. Power Requirements and Recommended Cable Sizes (Continued)

Model Number Imput Voltage Power Consumption Cable Size Cable Distance

BK700/200 230 VAC 9 watts 20 AWG 25,609 feet (7,805 m)

HK706-1 120 VAC 80 watts 20 AWG 533 feet (162 m)

HK706-2 24 VAC 80 watts 20 AWG 34 feet (10 m)

HK706-3 230 VAC 80 watts 20 AWG 2,881 feet (878 m)

HK708/10-1 120 VAC 107 watts 22 AWG 398 feet (121 m)

HK708/10-2 24 VAC 66 watts 20 AWG 42 feet (13 m)

HK708/10-3 230 VAC 84 watts 20 AWG 2,744 feet (836 m)

Combination of 120 VAC 84 watts 22 AWG 507 feet (155 m)

BK700 & 20 AWG 816 feet (249 m) HK706-1 18 AWG 1,291 feet (393 m)

Combination of 24 VAC 83 watts 20 AWG 33 feet (10 m)

BK700-24 & 18 AWG 52 feet (16 m)

HK706-2 16 AWG 83 feet (25 m)

Combination of 230 VAC 89 watts 20 AWG 2,590 feet (789 m)

BK700/220 & 18 AWG 4,095 feet (1,248 m)

HK706-3 16 AWG 6,505 feet (1,983 m)

Combination of 120 VAC 111 watts 22 AWG 384 feet (117 m)

BK700 & 20 AWG 618 feet (188 m)

HK708/10-1 18 AWG 977 feet (298 m)

Combination of 24 VAC 69 watts 20 AWG 40 feet (12 m)

BK700/24 & 18 AWG 63 feet (19 m) HK708/10-2 16 AWG 100 feet (30 m)

Combination of 230 VAC 93 watts 20 AWG 2,748 feet (755 m)

BK700/220 & 18 AWG 3,919 feet (1,194 m)

HK708/10-3 16 AWG 6,225 feet (1,897 m)

18 AWG 40,495 feet (12,342 m) 16 AWG 64,328 feet (19,606 m) 14 AWG 102,239 feet (31,161 m)

18 AWG 857 feet (261 m) 16 AWG 1,355 feet (413 m) 14 AWG 2,153 feet (656 m)

18 AWG 54 feet (17 m) 16 AWG 86 feet (26 m) 14 AWG 137 feet (42 m)

18 AWG 4,556 feet (1,389 m) 16 AWG 7,237 feet (2,206 m) 14 AWG 11,502 feet (3,506 m)

20 AWG 641 feet (195 m) 18 AWG 1,013 feet (3092 m) 16 AWG 1,6102 feet (491 m)

18 AWG 66 feet (20 m) 16 AWG 104 feet (32 m) 14 AWG 166 feet (51 m)

18 AWG 4,399 feet (1,322 m) 16 AWG 6,8928 feet (2,101 m) 14 AWG 10,954 feet (3,339 m)

16 AWG 2,051 feet (625 m)

14 AWG 132 feet (40 m)

14 AWG 10,339 feet (3,151 m)

16 AWG 1,552 feet (473 m)

14 AWG 159 feet (48 m)

14 AWG 9,894 feet (3,016 m)

Blower Kit

If you are istalling the blower kit in conjunction with a heater kit, skip this section and refer to

Blower and Heater Kits (Dual Installation)

To install a blower kit, perform the following steps:

1. Attach the blower assembly onto the brackets at the rear of the camera sled using the hardware provided (see Figure 1).

2. Wire as shown in Figure 2. Refer to Table A for recommended cable sizes.

Page 3

PC BOARD (230 VAC ONLY)

AC HIGH AC LOW GROUND

(120 VAC, 50/60 HZ INPUT)

FAN

1 2 3 4 5 6 7 8 9

THERMOSTAT

CIRCUIT BOARD

TERMINAL BLOCK

1 2 3 4 5 6 7 8 9

THERMOSTAT

CIRCUIT BOARD

TERMINAL BLOCK

1 2 3 4 5 6 7 8 9

THERMOSTAT

CIRCUIT BOARD

TERMINAL BLOCK

AC HIGH AC LOW GROUND

(230 VAC, 50/60 HZ INPUT)

AC HIGH AC LOW GROUND

(24 VAC, 50/60 HZ INPUT)

RESISTOR

FAN

DIODE BRIDGE

HEATER

WHITE WHITE WHITE WHITE

HEATER

WHITE WHITE WHITE WHITE

HEATER

WHITE WHITE WHITE WHITE

Heater Kit

If you are installing the heater kit in conjunction with a blower kit, skip this section and refer to

Blower and Heater Kits (Dual

Installation).

FAN

24 VAC

FAN

110 VAC

BLOWER ASSEMBLY

E700 SLED MOUNTING BRACKET

Figure 1. Blower Kit Installation

PCB9000277ASSY

DIODE BRIDGE RECTIFIER

BUTT SPLICES PROVIDED

BLK

AC IN

BLK

BUTT SPLICES PROVIDED

BK700/24 BLOWER WIRING DIAGRAM

RED

AC IN

BLK

BK700

BLOWER WIRING DIAGRAM

AC NEUT INPUT

AC HIGH INPUT

Perform the following steps to complete the heater kit installation:

1. Attach the PC board assembly onto the brackets that are attached to the rear of the camera sled (refer to Figure 3).

2. Attach the heater assembly onto the front of the camera sled (refer to Figure 3).

3. Route the wiring from the heater assembly along the side of the camera sled.

4. Wire power to the PC board. Refer to Figure 4 and Table A.

AC NEUT INPUT

AC HIGH INPUT

FAN

230 VAC

HEATER BRACKET ASSEMBLY

3K RESISTOR

BUTT SPLICES PROVIDED

AC IN

BLK

Figure 2. Blower Kit Wiring Diagram

REAR PLATE

CAMERA SLED

PC BOARD ASSEMBLY

Figure 3. Heater Kit Installation

BK700/220 BLOWER WIRING DIAGRAM

AC NEUT INPUT

AC HIGH INPUT

Figure 4. Blower and Heater Kits Wiring Diagram (All Models)

Page 4

Blower and Heater Kits (Dual Installation)

1. a. BK700 and BK700/24 - Remove the PC board from the heater assembly. Attach

board to the top bracket of the blower assembly.

b. BK700/220 - The blower and heater assemblies are both factory assembled with a

PC board. Only one PC board assembly is required. Remove the PC board from the blower assembly and replace it with the PC board from the heater assembly.

2. Attach the PC board and blower assembly onto the brackets that are attached to the rear of the camera sled (refer to Figure 1).

3. Attach the heater assembly onto the front of the camera sled (refer to Figure 3).

4. Route the wiring from the heater assembly along the side of the camera sled.

5. Wire the fan and power to the PC board. Refer to Figure 4 and Table A.

SERVICE MANUAL

If you need to order replacement parts, obtain a service manual in one of the following ways:

• Go to Pelco’s web site at www.pelco.com and find service manual C2412SM.

• Contact Pelco’s Literature Department and request service manual C2412SM.

PRODUCT WARRANTY AND RETURN INFORMATION

WARRANTY

Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment.

Exceptions to this warranty are as noted below:

• Five years on FT/FR8000 Series ﬁber optic products.

• Three years on Genex

• Three years on Camclosure CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2, and MC3651H-2X camera models, which have a ﬁve-year warranty.

•Two years on standard motorized or ﬁxed focal length lenses.

•Two years on Legacy ﬁxed dome products.

•Two years on Spectra continuous motion applications.

•Two years on Esprit

• Eighteen months on DX Series digital video recorders, NVR300 Series network video recorders, and Endura

• One year (except video heads) on video cassette recorders (VCRs). Video heads will be covered for a period of six months.

• Six months on all pan and tilts, scanners or preset lenses used in continuous motion applications (that is, preset scan, tour and auto scan modes).

Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco shipment. All goods requiring warranty repair shall be sent freight prepaid to Pelco, Clovis, California. Repairs made necessary by reason of misuse, alteration, normal wear, or accident are not covered under this warranty.

Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from the speciﬁc use or application made of the Products. Pelco’s liability for any claim, whether based on breach of contract, negligence, infringement of any rights of any party or product liability, relating to the Products shall not exceed the price paid by the Dealer to Pelco for such Products. In no event will Pelco be liable for any special, incidental or consequential damages (including loss of use, loss of proﬁt and claims of third parties) however caused, whether by the negligence of Pelco or otherwise.

The above warranty provides the Dealer with speciﬁc legal rights. The Dealer may also have additional rights, which are subject to variation from state to state.

Series products (multiplexers, server, and keyboard).

and ﬁxed camera models, except the CC3701H-2,

, CM6700/CM6800/CM9700 Series matrix, and DF5/DF8 Series

, Esprit®, ExSite™, and PS20 scanners, including when used in

and WW5700 Series window wiper (excluding wiper blades).

™

Series distributed network-based video products.

If a warranty repair is required, the Dealer must contact Pelco at (800) 289-9100 or (559) 292-1981 to obtain a Repair Authorization number (RA), and provide the following information:

1. Model and serial number

2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number

3. Details of the defect or problem

If there is a dispute regarding the warranty of a product which does not fall under the warranty conditions stated above, please include a written explanation with the product when returned.

Method of return shipment shall be the same or equal to the method by which the item was received by Pelco.

RETURNS

In order to expedite parts returned to the factory for repair or credit, please call the factory at (800) 289-9100 or (559) 292-1981 to obtain an authorization number (CA number if returned for credit, and RA number if returned for repair).

All merchandise returned for credit may be subject to a 20% restocking and refurbishing charge.

Goods returned for repair or credit should be clearly identiﬁed with the assigned CA or RA number and freight should be prepaid. Ship to the appropriate address below.

If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico, send goods to:

Service Department Pelco 3500 Pelco Way Clovis, CA 93612-5699

If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico and are instructed to return goods to the USA, you may do one of the following:

If the goods are to be sent by a COURIER SERVICE, send the goods to:

Pelco 3500 Pelco Way Clovis, CA 93612-5699 USA

If the goods are to be sent by a FREIGHT FORWARDER, send the goods to:

Pelco c/o Expeditors 473 Eccles Avenue South San Francisco, CA 94080 USA Phone: 650-737-1700 Fax: 650-737-0933

REVISION HISTORY

Manual # Date Comments

C2412M 11/99 Original version.