Pelco FR85081 User Manual

ADDENDUM

Addendum No.: C1648M ADDEN

Date: April 29, 2005

Manual Affected: FT85081/FR85081 Fiber Transmitter and Receiver

Installation Manual – C1648M

Manual Update:

Attachment of Ferrite to Data Cable of FT85081 Transmitter

A snap-on ferrite is supplied with the FT85081MSTR, FT85081SSTR, and FT85081SFCR transmitters. The ferrite must be attached to the data cable of the transmitters to comply with FCC and CE emissions requirements.

After data connections are made to the data connector on the transmitter, attach the ferrite to the data cable. When attaching the ferrite to the cable, position the ferrite as close as possible to the transmitter.

NOTE: The ferrite should fit securely around the cable. If the ferrite is loose and slides along the cable, loop the cable through the ferrite before closing the ferrite. If, however, the thickness of the cable prevents the ferrite from closing, use a tie wrap to hold the ferrite in place rather than looping the cable.

Pelco World Headquarters • 3500 Pelco Way, Clovis, California 93612-5699 USA USA & Canada: Tel: 800/289-9100 • Fax: 800/289-9150 International: Tel: 1-559/292-1981 • Fax: 1-559/348-1120

www.pelco.com

INSTALLATION

FT85081/FR85081 Fiber Transmitter

and Receiver

Eight-Channel Digitally Encoded Video with Bidirectional Data

C1648M (4/05)

Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Regulatory Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Product Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Optional Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Front Panel - FT85081 Transmitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Front Panel - FR85081 Receiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Rear Panel - FT85081 Transmitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Rear Panel - FR85081 Receiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Package Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Data Communication Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Mounting the Transmitter/Receiver into a Rack . . . . . . . . . . . . . . . . . . . . . . . . . .14

Mounting the Transmitter/Receiver Using the Wall Clip. . . . . . . . . . . . . . . . . . . . 15

Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Speciﬁcations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

List of Illustrations

1 Eight-Channel Video FT85081 Transmitter and FR85081 Receiver

with Bidirectional Data Channel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

2 Front Panel of FT85081 Transmitter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

3 Front Panel of FR85081 Receiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

4 Rear Panel of FT85081 Transmitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

5 Rear Panel of FR85081 Receiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

6 Data Selection Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

7 Mounting the FT85081 Transmitter/FR85081 Receiver Using the Wall Clip. . . . . . . . . . 15

8 FT85081 Transmitter/FR85081 Receiver Connections. . . . . . . . . . . . . . . . . . . . . . . . . . .16

9 RS-232 Data Communication Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

10 RS-422 Data Communication Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

11 RS-485 2-Wire (Half Duplex) Data Communication Wiring. . . . . . . . . . . . . . . . . . . . . . .20

12 RS-485 4-Wire (Full Duplex) Data Communication Wiring . . . . . . . . . . . . . . . . . . . . . . .21

13 Manchester Data Communication Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

14 Bi-Phase Data Communication Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

2 C1648M (4/05)

List of Tables

A Data Selection Switch Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

B Data Connector Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

CTroubleshooting with Front-Panel Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24

C1648M (4/05) 3

Important Safety Instructions

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including ampliﬁers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not ﬁt into your outlet consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the points where they exit from the apparatus.

11. Only use attachments/accessories speciﬁed by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table speciﬁed by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/ apparatus combination to avoid injury from tip-over.

13. Unplug this apparatus during lightning storms or when unused for long periods of time.

14. Refer all servicing to qualiﬁed service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

15. Apparatus shall not be exposed to dripping or splashing and that no objects ﬁlled with liquids, such as vases shall be placed on the apparatus.

WARNING:

16. rain or moisture.

17. Installation should be done only by qualiﬁed personnel and conform to all local codes.

18. Unless the unit is speciﬁcally marked as a NEMA Type 3, 3R, 3S, 4, 4X, 6, or 6P enclosure, it is designed for indoor use only and it must not be installed where exposed to rain and moisture.

19. Use only installation methods and materials capable of supporting four times the maximum speciﬁed load.

To reduce the risk of ﬁre or electric shock, do not expose this apparatus to

4 C1648M (4/05)

CAUTION:

RISK OF ELECTRIC SHOCK.

DO NOT OPEN.

To reduce the risk of electric shock do not perform any servicing other that contained in the operating instructions unless you are qualiﬁed to do so.

The product and/or manual may bear the following marks:

These servicing instructions are for use by qualiﬁed service personnel only.

This symbol indicates that dangerous voltage constituting a risk of electric shock is present within this unit.

This symbol indicates that there are important operating and maintenance instructions in the literature accompanying this unit.

C1648M (4/05) 5

Regulatory Notices

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

RADIO AND TELEVISION INTERFERENCE

This equipment has been tested and found to comply with the limits of a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

Changes and Modiﬁcations not expressly approved by the manufacturer or registrant of this equipment can void your authority to operate this equipment under Federal Communications Commission’s rules.

This Class A digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.

6 C1648M (4/05)

Product Overview

DESCRIPTION

The FT85081/FR85081 ﬁber transmitter and receiver provide the ability to transmit eight unidirectional composite video channels and one bidirectional data channel over one optical ﬁber (refer to Figure 1).

EIGHT VIDEO

INPUTS

DATA

Figure 1.

FT85081

TRANSMITTER

ONE

FIBER

FR85081

RECEIVER

Eight-Channel Video FT85081 Transmitter and FR85081 Receiver

EIGHT VIDEO

OUTPUTS

DATA

with Bidirectional Data Channel

Features of the FT85081/FR85081 ﬁber optic transmission system include the following:

• 8-bit digitally encoded video for high-quality multi-channel video transmission over a single ﬁber

• Bidirectional data channel that supports RS-232, RS-422, RS-485 (2-wire/4-wire), Manchester, and Bi-Phase communication

•Wavelength division multiplexing (WDM), allowing video and data channels to be transmitted in the same ﬁber using different wavelengths

• Multimode ﬁber support for distances up to 1 km (0.6 mi)

• Single-mode ﬁber support for distances up to 30 km (18.6 mi)

• Exceeds all requirements for the RS-250C Medium-Haul Transmission speciﬁcation

• Compatible with NTSC, PAL, and SECAM video standards

• No performance adjustments required

• 12 VDC or 24 VAC power supply

• Standalone and rack-mountable modular design

• LED indicators for monitoring of signal status, data activity, and operating power

NOTE:

The FT85081 transmitter/FR85081 receiver is a Class 1 laser product that complies with FDA radiation performance standard 21CFR Subchapter J and with IEC 60825-1 Edition 1.2, 2001-08.

C1648M (4/05) 7

MODELS

The FT85081/FR85081 ﬁber transmitter and receiver consist of the following series of models:

Multimode Models:

FT85081MSTR Eight-channel ﬁber optic video transmitter/single-channel data transceiver;

FR85081MSTR Eight-channel ﬁber optic video receiver/single-channel data transceiver;

Single-Mode Models:

FT85081SSTR Eight-channel ﬁber optic video transmitter/single-channel data transceiver;

FR85081SSTR Eight-channel ﬁber optic video receiver/single-channel data transceiver;

FT85081SFCR Eight-channel ﬁber optic video transmitter/single-channel data transceiver;

FR85081SFCR Eight-channel ﬁber optic video receiver/single-channel data transceiver;

OPTIONAL ACCESSORIES

The following optional accessories are available: RK5000-3U 19-inch rack mount chassis for 14 slots (no power), 3 RUs RK5000PS-3U 19-inch rack mount chassis for 12 slots with power, 3 RUs EPS5000-120 External/redundant power supply, 1 RU, 120 W x 2 RK5001B-3U Blank ﬁller panel, single width RK5002B-3U Blank ﬁller panel, double width RK5003-1UEXP Adapter kit that allows a 3 RU triple-width ﬁber optic module to be used in

multimode, ST connector

single-mode, ST connector

single-mode, FC connector

RK5000PS-5U rack mount chassis

8 C1648M (4/05)

FRONT PANEL

The front panel of the FT85081 transmitter and the FR85081 receiver provides LED indicators that allow you to monitor data activity, signal status, and operating power. The following sections provide a view of the front panel of the FT85081 transmitter and the FR85081 receiver.

FRONT PANEL - FT85081 TRANSMITTER

Figure 2 illustrates the front panel of the FT85081 transmitter.

 





Figure 2.



DATA TX LED



DATA RX LED



CARRIER DETECT LED



POWER LED (Pelco badge)



VIDEO PRESENT LEDs (1-8)

For detailed information about the front-panel indicators, refer to the

Front Panel of FT85081 Transmitter



Troubleshooting

section.

C1648M (4/05) 9

+ 23 hidden pages