Pelco FR85041 User Manual

ADDENDUM

Addendum No.

Date

Manual Affected

Manual Update

C1645M-A ADDEN

September 14, 2006

FT85041/FR85041 Fiber Transmitter and Receiver Installation Manual –

C1645M-A

Attachment of Ferrite to Data Cable of FT85041/ CT85041 Transmitter

A snap-on ferrite is supplied with the FT85041MSTR/CT85041MSTR, FT85041SSTR/ CT85041SSTR, and FT85041SFCR/CT85041SFCR transmitters. The ferrite must be attached to the data cable of the transmitters to comply with FCC and CE emissions requirements.

After the data connections are made to the data connector on the transmitter, attach the ferrite to the data cable. When attaching the ferrite to the cable, position the ferrite as close as possible to the transmitter.

NOTE:

The ferrite should ﬁt securely around the cable. If the ferrite is loose and slides along the cable, loop the cable through the ferrite before closing the ferrite. If, however, the thickness of the cable prevents the ferrite from closing, use a tie wrap to hold the ferrite in place rather than looping the cable.

The materials used in the manufacture of this document and its components are compliant to the requirements of Directive 2002/95/EC.

Pelco Worldwide Headquarters

3500 Pelco Way • Clovis, California 93612 USA

USA & Canada International www.pelco.com

• Tel: 800/289-9100 • Fax: 800/289-9150

• Tel: 1-559/292-1981 • Fax: 1-559/348-1120

INSTALLATION

FT85041/FR85041 Fiber Transmitter

and Receiver

Four-Channel Digitally Encoded Video with Bidirectional Data

C1645M-A (9/06)

Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Regulatory Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Product Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Optional Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Front Panel - FT85041 Transmitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Front Panel - FR85041 Receiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Rear Panel - FT85041 Transmitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Rear Panel - FR85041 Receiver. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Data Communication Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Mounting the Transmitter/Receiver into a Rack . . . . . . . . . . . . . . . . . . . . . . 16

Mounting the Transmitter/Receiver to a Wall . . . . . . . . . . . . . . . . . . . . . . . . 16

Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

List of Illustrations

1 Four-Channel Video FT85041 Transmitter and FR85041 Receiver

with Bidirectional Data Channel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

2 Front Panel of FT85041 Transmitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

3 Front Panel of FR85041 Receiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

4 Rear Panel of FT85041 Transmitter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

5 Rear Panel of FR85041 Receiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

6 Data Selection Switch. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

7 Mounting the FT85041 Transmitter/FR85041 Receiver Using the Wall Clip . . . 17

8 FT85041 Transmitter/FR85041 Receiver Connections . . . . . . . . . . . . . . . . . . . . 18

9 RS-232 Data Communication Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

10 RS-422 Data Communication Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

11 RS-485 2-Wire (Half Duplex) Data Communication Wiring . . . . . . . . . . . . . . . . 22

12 RS-485 4-Wire (Full Duplex) Data Communication Wiring. . . . . . . . . . . . . . . . . 23

13 Manchester Data Communication Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

14 Bi-Phase Data Communication Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

C1645M-A (9/06) 3

List of Tables

A Data Selection Switch Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

B Data Connector Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

C Troubleshooting with Front-Panel Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

4 C1645M-A (9/06)

Important Safety Instructions

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including ampliﬁers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not ﬁt into your outlet consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the points where they exit from the apparatus.

11. Only use attachments/accessories speciﬁed by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table speciﬁed by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13. Refer all servicing to qualiﬁed service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

14. Apparatus shall not be exposed to dripping or splashing and that no objects ﬁlled with liquids, such as vases shall be placed on the apparatus.

WARNING:

15. or moisture.

16. Installation should be done only by qualiﬁed personnel and conform to all local codes.

17. Use only installation methods and materials capable of supporting four times the maximum speciﬁed load.

18. A CCC-approved power cord must be used to power this equipment when used in China.

CAUTION:

19. reduce the risk of electric shock do not perform any servicing other than that contained in the operating instructions unless you are qualiﬁed to do so.

To reduce the risk of ﬁre or electric shock, do not expose this apparatus to rain

These servicing instructions are for use by qualiﬁed service personnel only. To

C1645M-A (9/06) 5

The product and/or manual may bear the following marks:

CAUTION:

RISK OF ELECTRIC SHOCK.

DO NOT OPEN.

This symbol indicates that dangerous voltage constituting a risk of electric shock is present within this unit.

This symbol indicates that there are important operating and maintenance instructions in the literature accompanying this unit.

6 C1645M-A (9/06)

Regulatory Notices

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

RADIO AND TELEVISION INTERFERENCE

This equipment has been tested and found to comply with the limits of a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

Changes and Modiﬁcations not expressly approved by the manufacturer or registrant of this equipment can void your authority to operate this equipment under Federal Communications Commission’s rules.

This Class A digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.

C1645M-A (9/06) 7

Product Overview

DESCRIPTION

The FT85041/FR85041 ﬁber transmitter and receiver provide the ability to transmit four unidirectional composite video channels and one bidirectional data channel over one optical ﬁber (refer to Figure 1).

FOUR

VIDEO

INPUTS

DATA

Figure 1.

FT85041

TRANSMITTER

ONE

FIBER

FR85041

RECEIVER

Four-Channel Video FT85041 Transmitter and FR85041 Receiver

FOUR

VIDEO

OUTPUTS

DATA

with Bidirectional Data Channel

Features of the FT85041/FR85041 ﬁber optic transmission system include the following:

•

8-bit digitally encoded video for high-quality multichannel video transmission over a single ﬁber

•

Bidirectional data channel that supports RS-232, RS-422, RS-485 (2-wire/4-wire), Manchester, and Bi-Phase communication

•

Wavelength division multiplexing (WDM), allowing video and data channels to be transmitted in the same ﬁber using different wavelengths

•

Multimode ﬁber support for distances up to 2 km (1.2 mi)

•

Single-mode ﬁber support for distances up to 30 km (18.6 mi)

•

Exceeds all requirements for the RS-250C Medium-Haul Transmission speciﬁcation

•

Compatible with NTSC, PAL, and SECAM video standards

•

Designed to meet NEMA TS 2 and Caltrans trafﬁc signal control equipment standards for ambient operating temperature, mechanical shock and vibration, humidity with condensation, high-line/low-line voltage conditions, and transient voltage protection

NOTE:

Conformal coating is required for operation in environments with relative humidity

above 95% (condensing).

•

No performance adjustments required

•

12 VDC or 24 VAC power supply

•

Stand-alone and rack-mountable modular design

•

LED indicators for monitoring of signal status, laser status, data activity, and operating power

The FT85041 transmitter/FR85041 receiver is a Class 1 laser product that complies with FDA radiation performance standard 21CFR Subchapter J and with IEC 60825-1 Edition 1.2, 2001-08.

8 C1645M-A (9/06)

MODELS

The FT85041/FR85041 ﬁber transmitter and receiver consist of the following series of models:

Multimode Models:*

FT85041MSTR Four-channel ﬁber optic video transmitter/single-channel data transceiver;

multimode, ST connector

FR85041MSTR Four-channel ﬁber optic video receiver/single-channel data transceiver;

multimode, ST connector

Single-Mode Models:*

FT85041SSTR Four-channel ﬁber optic video transmitter/single-channel data transceiver;

single-mode, ST connector

FR85041SSTR Four-channel ﬁber optic video receiver/single-channel data transceiver;

single-mode, ST connector

FT85041SFCR Four-channel ﬁber optic video transmitter/single-channel data transceiver;

single-mode, FC connector

FR85041SFCR Four-channel ﬁber optic video receiver/single-channel data transceiver;

single-mode, FC connector

*For conformal coated models, replace the ﬁrst letter F in the model number with the letter

The conformal coated version of FT85041MSTR, for example, is CT85041MSTR.

OPTIONAL ACCESSORIES

The following optional accessories are available:

WM5002-3U Wall mount base kit for double-width module

WM5002-3UEXP Wall mount expansion kit for double-width module

RK5000-3U 19-inch rack mount chassis for 14 slots (no power), 3 RUs

RK5000PS-3U 19-inch rack mount chassis for 12 slots with power, 3 RUs

EPS5000-120 External rack power supply, 1 RU, dual 120 W power outputs

RK5001B-3U Blank ﬁller panel, single width

RK5002B-3U Blank ﬁller panel, double width

RK5002-1UEXP Adapter kit that allows a 3 RU double-width ﬁber optic module to be used in

RK5000PS-5U rack mount chassis

C1645M-A (9/06) 9

+ 23 hidden pages