Pelco FR85011A User Manual

INSTALLATION

FT85011A/FR85011A Fiber Transmitter

and Receiver

Single-Channel Digitally Encoded Video with Bidirectional Data

C2604M (7/06)

Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Regulatory Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Product Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Models. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Optional Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Front Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Data Communication Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Mounting the Transmitter/Receiver into a Rack . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Mounting the Transmitter/Receiver to a Wall . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

List of Illustrations

1 FT85011A Transmitter and FR85011A Receiver Single-Channel Video

and Data Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

2 Front Panel of FT85011A Transmitter and FR85011A Receiver . . . . . . . . . . . . . . . . . . . 10

3 Rear Panel of FT85011A Transmitter and FR85011A Receiver . . . . . . . . . . . . . . . . . . . . 11

4 Data Selection Switch. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

5 Mounting the FT85011A Transmitter/FR85011A Receiver Using the Wall Clip. . . . . . . 15

6 FT85011A Transmitter/FR85011A Receiver Connections . . . . . . . . . . . . . . . . . . . . . . . . 16

7 RS-232 Data Communication Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

8 RS-422 Data Communication Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

9 RS-485 2-Wire (Half Duplex) Data Communication Wiring . . . . . . . . . . . . . . . . . . . . . . 20

10 RS-485 4-Wire (Full Duplex) Data Communication Wiring . . . . . . . . . . . . . . . . . . . . . . . 21

11 Manchester Data Communication Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

12 Bi-Phase Data Communication Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

List of Tables

A Data Communication Switch Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

B Data Connector Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

C Troubleshooting with Front-Panel Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

C2604M (7/06) 3

Important Safety Instructions

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including ampliﬁers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not ﬁt into your outlet consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the points where they exit from the apparatus.

11. Only use attachments/accessories speciﬁed by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table speciﬁed by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13. Refer all servicing to qualiﬁed service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

14. Apparatus shall not be exposed to dripping or splashing and that no objects ﬁlled with liquids, such as vases shall be placed on the apparatus.

WARNING:

15. or moisture.

16. Installation should be done only by qualiﬁed personnel and conform to all local codes.

17. Use only installation methods and materials capable of supporting four times the maximum speciﬁed load.

18. A CCC-approved power cord must be used to power this equipment when used in China.

CAUTION:

19. To reduce the risk of electric shock do not perform any servicing other than that contained in the operating instructions unless you are qualiﬁed to do so.

To reduce the risk of ﬁre or electric shock, do not expose this apparatus to rain

These servicing instructions are for use by qualiﬁed service personnel only.

4 C2604M (7/06)

The product and/or manual may bear the following marks:

CAUTION:

RISK OF ELECTRIC SHOCK.

DO NOT OPEN.

This symbol indicates that dangerous voltage constituting a risk of electric shock is present within this unit.

This symbol indicates that there are important operating and maintenance instructions in the literature accompanying this unit.

C2604M (7/06) 5

Regulatory Notices

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

RADIO AND TELEVISION INTERFERENCE

This equipment has been tested and found to comply with the limits of a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

Changes and Modiﬁcations not expressly approved by the manufacturer or registrant of this equipment can void your authority to operate this equipment under Federal Communications Commission’s rules.

This Class A digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.

6 C2604M (7/06)

Product Overview

DESCRIPTION

The FT85011A/FR85011A ﬁber transmitter and receiver provide the ability to transmit one unidirectional composite video channel and one bidirectional data channel over one optical ﬁ ber. In addition, patentpending technology provides the solution for allowing Coaxitron be transmitted the full distance of the ﬁber (up to 6 km for multimode ﬁber and up to 46 km for singlemode ﬁber). Figure 1 illustrates FT85011A transmitter and FR85011A receiver single-channel video and data applications.

pan/tilt/zoom (PTZ) control data to

ONE VIDEO INPUT

DATA

ONE VIDEO INPUT

COAXITRON

DATA

Figure 1.

FT85011A

TRANSMITTER

AND BIDIRECTIONAL DATA APPLICATION

FT85011A

TRANSMITTER

SINGLE-CHANNEL VIDEO

AND COAXITRON DATA APPLICATION

ONE

FIBER

SINGLE-CHANNEL VIDEO

ONE

FIBER

FR85011A RECEIVER

FT85011A Transmitter and FR85011A Receiver Single-Channel Video

ONE

VIDEO

OUTPUT

DATA

ONE

VIDEO

OUTPUT

COAXITRON

DATA

and Data Applications

Features of the FT85011A/FR85011A ﬁber optic transmission system include the following:

•

8-bit digitally encoded video for high-quality video transmission over a single ﬁber

•

Bidirectional data channel that supports RS-232, RS-422, RS-485 (2-wire/4-wire), Manchester, Bi-Phase, and Coaxitron communication

•

Patent-pending transmission technology allowing for Coaxitron control at full-distance capabilities

•

Integrated wavelength division multiplexing (WDM), allowing video and data channels to be transmitted in the same ﬁber using different wavelengths

•

Multimode ﬁber support for distances up to 6 km

•

Single-mode ﬁber support for distances up to 46 km

•

Exceeds all requirements for the RS-250C Medium-Haul Transmission speciﬁcation

•

Compatible with NTSC, PAL, and SECAM video standards

C2604M (7/06) 7

•

Meets NEMA TS 2 and Caltrans trafﬁc signal control equipment standards for ambient operating temperature, mechanical shock and vibration, humidity with condensation, high-line/low-line voltage conditions, and transient voltage protection

NOTE:

Conformal coating is required for operation in environments with relative humidity

above 95% (condensing).

•

No performance adjustments required

•

12 VDC or 24 VAC power supply

•

Stand-alone and rack-mountable modular design

•

LED indicators for monitoring of signal status, laser status, data activity, and operating power

In addition, note the following:

•

The FT85011A transmitter/FR85011A receiver is a Class 1 laser product that complies with FDA radiation performance standard 21CFR Subchapter J and with IEC 60825-1 Edition 1.2, 2001-08.

•

In addition to compatibility with each other, the FT85011A transmitter and the FR85011A receiver are compatible with other ﬁber models:

–

The FT85011A transmitter is backward compatible with the FR85011 receiver.

–

The FR85011A receiver is backward compatible with the FS85011 and FT85011 transmitters.

For optical power budget and maximum transmission distance speciﬁcations of the various module-compatible pairs, refer to the

Speciﬁcations

section. For additional information about

the FR85011, FS85011, and FT85011 modules, refer to the manual supplied with the modules.

8 C2604M (7/06)

MODELS

The FT85011A/FR85011A ﬁber transmitter and receiver consist of the following series of models :

Multimode Models:*

FT85011AMSTR Single-channel ﬁber optic video transmitter/data transceiver; multimode,

ST connector

FR85011AMSTR Single-channel ﬁber optic video receiver/data transceiver; multimode,

ST connector

Single-Mode Models:*

FT85011ASSTR Single-channel ﬁber optic video transmitter/data transceiver; single-mode,

ST connector

FR85011ASSTR Single-channel ﬁber optic video receiver/data transceiver; single-mode,

ST connector

FT85011ASFCR Single-channel ﬁber optic video transmitter/data transceiver; single-mode,

FC connector

FR85011ASFCR Single-channel ﬁber optic video receiver/data transceiver; single-mode,

FC connector

*For conformal coated models, replace the ﬁrst letter F in the model number with the letter

The conformal coated version of FT85011AMSTR, for example, is CT85011AMSTR.

OPTIONAL ACCESSORIES

The following optional accessories are available:

WM5001-3U Wall mount base kit for single-width module

WM5001-3UEXP Wall mount expansion kit for single-width modul e

RK5000-3U 19-inch rack mount chassis for 14 slots (no power), 3 RUs

RK5000PS-3U 19-inch rack mount chassis for 12 slots with power, 3 RUs

EPS5000-120 External rack power supply, 1 RU, dual 120 W power outputs

RK5001B-3U Blank ﬁller panel, single width

RK5002B-3U Blank ﬁller panel, double width

RK5001-1UEXP Adapter kit that allows a 3 RU single-width ﬁber module to be used in

RK5000PS-5U rack mount chassis

C2604M (7/06) 9

FRONT PANEL

The front panel of the FT85011A transmitter and the FR85011A receiver provides LED indicators that allow you to monitor data activity, signal status, laser status, and operating power (refer to Figure 2).

  

 

FT85011A

TRANSMITTER

Figure 2.



DATA TX LED



DATA RX LED



VIDEO PRESENT LED



OPTIC FAULT LED (optical signal status/laser status indicator)



POWER LED (Pelco badge)

For detailed information about the front-panel indicators, refer to the

Front Panel of FT85011A Transmitter and FR85011A Receiver

FR85011A

RECEIVER

 

 



Troubleshooting

section.

10 C2604M (7/06)

+ 22 hidden pages