PRODUCT SPECIFICATION
camera solutions
ES40E/ES41E Series IP Positioning System
ES40E/ES41E ESPRIT® SE IP, H.264, DIGITAL STANDARD AND PRESSURIZED MODELS
Product Features
• Receiver, Pan/Tilt, and Enclosure with Integrated Optics Package
(IOP) or Pressurized Integrated Optics Cartridge (IOC), NTSC/PAL
• Tilt Range of +34° to –83° from Horizontal
• Ability to Control and Monitor Video Over IPv4 and IPv6 Networks
• H.264, MPEG-4, and MJPEG Compression
• Multilevel Password Protection
• Autotracking
• Horizontal Zone and Window Blanking
• On-Screen Compass and Tilt Display
• 256 Configurable Preset Positions
• Open IP Standards
Pelco’s ES40E/ES41E Esprit® SE IP Positioning System features a
receiver, pan/tilt, enclosure, and either an Integrated Optics Package
(IOP) or a pressurized Integrated Optics Cartridge (IOC) in a single,
easy-to-install system. Options include IOP or IOC models with or
without wiper.
The ES41E Series includes a window wiper. The wiper is completely
integrated into the enclosure and does not interfere with the viewing
range of the system. The wiper can be configured to delay between
wipes and to automatically shut off after a specified period. The
wiper design also allows for easy replacement of the wiper blade.
A built-in heater, window defroster/defogger, sun shroud, and
insulation blanket are standard features on the ES40E/ES41E units,
which also include open collector auxiliary output that functions for
two seconds before deactivating.
Esprit SE IP systems incorporate all of the features and functions of
Esprit SE, while allowing you to control and monitor video over an IP
network from virtually anywhere in the world. Esprit SE IP is a
high-speed positioning system with a built-in 100Base-TX network
interface for live streaming to any network application.
Esprit SE IP supports two simultaneous video streams. The two
streams can be compressed in H.264, MPEG-4, and MJPEG formats
across several resolution configurations. The streams can be
configured in a variety of frame rates, bit rates, and group of pictures
(GOP) structures for additional bandwidth administration. The H.264
compression video files are up to 20 times smaller than MJPEG,
making network video storage more affordable.
Web Interface
Esprit SE IP uses a standard Web browser for powerful remote setup
and administration.
Network protocols such as Secure Sockets Layer (SSL) configuration
for security certificates, Secure Shell (SSH) for remote login, and
Quality of Service (QoS) for priority or guaranteed data flow can be
managed using a Web browser.
Video Systemization
Esprit SE IP easily connects to Pelco IP and hybrid systems such as
®
version 1.5 (or later), MPEG-4; Endura version 2.0 (or later),
Endura
H.264; Digital Sentry
later); DX4700/DX4800 Series 1.1 (or later); DX4700HD/DX4800HD
Series v2.0 (or later); and DVR5100 version 1.5.4 (or later). The camera
also features open architecture connectivity to third-party software.
Pelco offers an application programming interface (API) and software
developer’s kit (SDK) for interfacing with Pelco’s IP cameras.
®
version 7.3 (or later); DX8100 version 2.0 (or
International Standards
Organization Registered Firm;
ISO 9001 Quality System
C2929 / REVISED 3-27-15
VIDEO
Video Encoding H.264 base profile, MPEG-4, and MJPEG
Video Streams Up to 2 simultaneous streams; the second
Frame Rate Up to 30, 25, 24, 15, 12.5, 12, 10, 8, 7. 5, 6, 5,
Available Resolutions Resolution JPEG H.264 Base Profile MPEG-4
stream is variable based on the setup of the
primary stream
4, 3, 2, 1 (dependent upon coding, resolution,
and stream configuration)
Width Height Format
Maximum
IPS
Recommended
Bit Rate
Maximum
IPS
Recommended
Bit Rate
Maximum
IPS
Recommended
704 480 NTSC 30 ips 5.4 Mbps 30 ips 1.9 Mbps 30 ips 2.0 Mbps
352 240 NTSC 30 ips 1.3 Mbps 30 ips 0.5 Mbps 30 ips 0.6 Mbps
704 576 PAL 25 ips 5.4 Mbps 25 ips 1.9 Mbps 25 ips 2.0 Mbps
Bit Rate
Supported Protocols TCP/IP, UDP/IP (Unicast, Multicast IGMP),
UPnP, DNS, DHCP, RTP, RTSP, NTP, IPv4, IPv6*,
SNMP, QoS, HTTP, HTTPS, LDAP (client), SSH,
SSL, SMTP, FTP, and 802.1x (EAP)
Users
Unicast Up to 20 simultaneous users depending on
resolution settings (2 guaranteed streams)
Multicast Unlimited users H.264 or MPEG-4
Security Access Password protected
Software Interface Web browser view and setup, up to
16 cameras
Pelco System Integration Endura 1.5 or later (MPEG-4) or Endura 2.0 or
later (H.264); Digital Sentry 7.3 IP bundle 3 or
later; DX8100 Series 2.0 or later;
DX4700/DX4800 Series 1.1 or later;
DX4700HD/DX4800HD Series v2.0 or later;
and DVR5100 version 1.5.4 or later
Open API Pelco API or ONVIF v1.02
Minimum System Requirements
Processor Intel
Operating System Microsoft
®
Pentium® 4 microprocessor, 1.6 GHz
®
Windows® XP, Windows Vista®,
Windows 7, or Mac
®
OS X 10.4 (or later)
Memory 512 MB RAM
Network Interface Card 100 megabits (or greater)
Monitor Minimum of 1024 x 768 resolution, 16- or
32-bit pixel color resolution
Web Browser Internet Explorer
Firefox
Media Player
†
Pelco Media Player or QuickTime® 7.6.5 for
®
3.0 (or later)
®
7.0 (or later) or Mozilla®
Windows XP, Windows Vista, or QuickTime
7.6.4 for Mac OS X 10.4
*Supports mixed IPv4 and IPv6 installations, but not IPv6-only deployments.
†
This product is not compatible with QuickTime version 7.6.4 for Windows XP
or Windows Vista. If you have this version installed on your PC, you will
need to upgrade to QuickTime version 7.6.5.
CAMERA/OPTICS
Signal Format NTSC, PAL
Scanning System Interlace/progressive selectable
Image Sensor 1/4-inch EXview HAD
Signal-to-Noise Ratio 48 dB, maximum
Effective pixels
NTSC 768 (H) X 494 (V)
PAL 752 (H) X 582 (V)
Horizontal Resolution >540 TV lines
Lens f/1.4 (focal length, 3.3 ~ 119 mm optical)
Zoom 36X optical, 12X digital
Zoom Speed (optical range) 3.2/4.6/6.6 seconds
Horizontal
Angle of View 57.2° at 3.3 mm wide zoom;
Focus Automatic with manual override
Maximum Sensitivity
NTSC 0.55 lux at 1/60 sec shutter (color)
PAL 0.45 lux at 1/50 sec shutter (color)
Sync System AC line lock, phase adjustable using remote
White Balance Automatic with manual override
Shutter Speed Automatic manual
NTSC 1/2 ~ 1/30,000
PAL 1/1.5 ~ 1/30,000
Iris Control Automatic with manual override
Gain Control Automatic/OFF
Electronic Image Stabilization Integrated
Wide Dynamic Range 128X
1.7° at 119 mm telephoto zoom
90% scene reflectance;
f/1.4 (focal length, 3.3 ~ 119 mm); 27 dB gain;
35 IRE (245 mV equivalent)
0.018 lux at 1/2 sec shutter (color)
0.055 lux at 1/60 sec shutter (B-W)
0.0018 lux at 1/ 2 sec shutter (B-W)
0.015 lux at 1/1.5 sec shutter (color)
0.045 lux at 1/50 sec shutter (B-W)
0.0015 lux at 1/1.5 sec shutter (B-W)
control, V-Sync
™
ELECTRICAL
Input Voltage 24, 120, or 230 VAC, 50/60 Hz; switch
Input Voltage Range ±10%
Power Consumption Maximum 75 VA per system
Heater and Defroster Thermostatically controlled
Electrical Connections 2 power source connections made at mount
Aux 2 Open collector output with 2-second
selectable for 120/230 VAC inputs
location with wire splices and 1 ground wire
splice
activation; connected relay must require no
more than 32 VDC and 40 mA to energize
relay coil; wire length between Esprit SE and
relay must be less than 30 m (100 ft)
MECHANICAL
Pan Movement 360° Continuous pan rotation
Vertical Tilt Unobstructed +34° to –83°, ±2°
Variable Pan/Tilt Speed
Pan 0.1° to 40°/sec variable-speed operation,
Tilt 0.1° to 30°/sec variable-speed operation
Configurable Preset Positions 256
Preset Speeds
Pan 100°/sec
Tilt 30°/sec
Camera Mounting Integrated camera sled assembly
Latches One link-lock, No. 3 stainless-steel latch; can
100°/sec turbo
be secured with padlock (not supplied)
GENERAL
Construction Die-cast, extruded and sheet aluminum;
Finish Gray polyester powder coat
Viewing Window 5.84 mm (0.23-inch) thick, optically clear,
Operating Temperature –45° to 50°C (–50° to 122°F) for sustained
Operating Environment Will remain operational in 145 kph (90 mph)
Operating Humidity
Unit Standard with IOP: 5 to 90% relative humidity
Weight With With
Unit
Standard with IOP 9.0 kg (20 lb) 9.9 kg (22 lb)
With Wiper and IOP 9.5 kg (21 lb) 10.4 kg (23 lb)
Standard with IOC 9.5 kg (21 lb) 10.4 kg (23 lb)
With Wiper and IOC 10.0 kg (22 lb) 11.0 kg (24 lb)
Shipping
Standard with IOP 11.3 kg (25 lb) 12.6 kg (28 lb)
With Wiper and IOP 11.7 kg (26 lb) 13.1 kg (29 lb)
Standard with IOC 11.7 kg (26 lb) 13.1 kg (29 lb)
With Wiper and IOC 12.3 kg (27 lb) 13.6 kg (30 lb)
stainless steel hardware
polycarbonate with proprietary
impact-resistant UV rated coating
system operation or 60°C (140°F) absolute
maximum; within two hours after power-up,
the entire unit can de-ice and be operational
from a temperature of –25°C (–13°F)
wind conditions;
withstands 209 kph (130 mph)
(noncondensing)
Standard with IOC: 5 to 100% relative
humidity (condensing)
Pedestal Adapter Wall Mount
CERTIFICATIONS/RATINGS/PATENTS
IOP MODELS
• CE, Class A
• FCC, Class A
• UL/cUL Listed, C-Tick
®
•Cisco
Medianet (MSP) compatible
• Meets NEMA Type 4X and IP66 standards
• U.S. Patents 340,940 and 5,224,675
IOC MODELS
• CE, Class A
• FCC, Class A
• UL/cUL Listed, C-Tick
®
•Cisco
Medianet (MSP) compatible
• Meets NEMA Type 4X and IP66 standards
• Meets IP67 standards (Pressurized IOC)
• U.S. Patent D472,260
MODEL NUMBERS
24.90
(9.80)
37.00
(14.60)
33.90
(13.3)
47.67
(18.77)
20.00
(7.90)
19.70
(7.70)
9.10
(3.60)
13.30
(5.20)
9.90
(3.90)
VALUES IN PARENTHESES ARE INCHES; ALL OTHERS ARE CENTIMETERS.
Pelco, the Pelco logo, and other trademarks associat ed with Pelco products referred
to in this publication are trademarks of Pelco, Inc. or its affiliate s. ONVIF and the
ONVIF logo are trademarks of ONVIF Inc. All other product names and
services are the property of their respective companies.
Product specifications and availability are subject to change without notice.
©Copyright 2015, Pelco, Inc. All rights reserved.
MODELS
Enclosure Type
Standard with IOP
With Wiper and IOP
Standard with IOC
With Wiper and IOC
Signal
Format
NTSC
PAL
NTSC
PAL
NTSC
PAL
NTSC
PAL
Pedestal Mount* Wall Mount
24 VAC 120/230 VAC 24 VAC 120/230 VAC
ES40E36-2N
ES40E36-2N-X
ES41E36-2N
ES41E36-2N-X
ES40EP36-2N
ES40EP36-2N-X
ES41EP36-2N
ES41EP36-2N-X
ES40E36-5N
ES40E36-5N-X
ES41E36-5N
ES41E36-5N-X
ES40EP36-5N
ES40EP36-5N-X
ES41EP36-5N
ES41EP36-5N-X
ES40E36-2W
ES40E36-2W-X
ES41E36-2W
ES41E36-2W-X
ES40EP36-2W
ES40EP36-2W-X
ES41EP36-2W
ES41EP36-2W-X
*Pedestal mount models include Esprit EPP pedestal adapter plate. Use with PM2000/PM2010 mount (not supplied) for
pedestal application.
†
Wall mount models include Esprit EWM wall mount. Optional mounting adapters for corner, pole, and parapet applications
are available.
REPLACEMENT INTEGRATED OPTICS PACKAGE (IOP)
The following IOP modules are replacement components only; they are not
interchangeable.
ESIOP36 Esprit high resolution day/night camera and
ESIOP36-X Same as ESIOP36 except PAL format
lens module, 36X, NTSC format
†
ES40E36-5W
ES40E36-5W-X
ES41E36-5W
ES41E36-5W-X
ES40EP36-5W
ES40EP36-5W-X
ES41EP36-5W
ES41EP36-5W-X
REPLACEMENT PRESSURIZED INTEGRATED OPTICS
CARTRIDGE (IOC)
The following IOC models are replacement components only; they are not
interchangeable.
IOC-36 Esprit high resolution day/night camera and
lens module, 36X, NTSC format
IOC-36-X Same as IOC-36 except PAL format
SECURE-SLA License Enables Information Assurance compliant
mode of operation
OPTIONAL ACCESSORIES
ES-REPLBLADE-2 Package of 2 window wiper replacement
ES-REPLBLADE-10 Package of 10 window wiper replacement
blades
blades
OPTIONAL MOUNTS AND ADAPTERS
ECM100 Corner mount adapter for use with EWM wall
EPM Pole mount adapter for use with EWM wall
EA4348 EWM-to-Legacy adapter; use with PP4348
PM2000/PM2010 Pedestal mount with cable feedthrough;
RECOMMENDED POWER SUPPLIES
MCS Series Multiple 24 VAC camera power supply, indoor
WCS Series Single/multiple 24 VAC camera power supply,
mount
mount
parapet mount
for use with Esprit systems with EPP pedestal
adapter plate
outdoor
Pelco by Schneider Electric
3500 Pelco Way, Clovis, California 93612-5699 United States
USA & Canada Tel (800) 289-9100 Fax (800) 289-9150
International Tel +1 (559) 292-1981 Fax +1 (559) 348-1120
www.pelco.com www.pelco.com/community
Loading...