Pelco EWM, EPM, ECM101, EPP2 installation manual

INSTALLATION

Esprit® Enhanced Mounts

EWM, EPM, ECM101, EPP2

Wall, Pole, Corner, and Pedestal

C1356M-A (9/18)

Important Safety Instructions

1. Installation and servicing should only be done by qualified service personnel and conform to all local codes.

2. Use only installation methods and materials capable of supporting four times the maximum specified load.

3. Use stainless steel hardware to fasten the mount to outdoor surfaces.

4. To prevent damage from water leakage when installing a mount outdoors on a roof or wall, apply sealant around the bolt holes between the
mount and mounting surface.

Description

This manual contains the installation instructions for the following Esprit® Enhanced mounts:

NOTE: Esprit Enhanced mounts do not ship with conduit fittings or mounting hardware, unless noted otherwise.

EWM Wall Mount: Use to mount an Esprit Enhanced system directly to a vertical load bearing surface.

Qty Description

1Wall mount
1 Conduit plate
1 Gasket
3 10-32 x 3/4-inch Philips flat head screws
2 Sealing glands

EPM Pole Mount: Use with EWM to mount an Esprit Enhanced system to a pole.

Qty Description

1 Pole mount
3 Stainless steel straps
4 3/8-inch flat washers
4 5/16-18 nuts
4 5/16-inch lock washers

ECM101 Corner Mount: Use with EWM to mount an Esprit Enhanced system to a building corner.

Qty Description

1 Corner mount
1 Corner mount with 5/16-18 x 1.25-inch studs
4 3/8-inch flat washers
4 5/16-18 nuts
4 5/16-inch lock washers

EPP2 Pedestal Adapter: Use to mount an Esprit Enhanced system directly to a pedestal mount; includes pedestal adapter only.

Qty Description

3 10-32 x 1/2-inch Phillips flathead screws

2 C1356M-A (9/18)

Installation

SEALING
GLAND

KNOCKOUT

NOTE: Before installing any mount or Esprit Enhanced system, refer to Video and Power Cable Wiring Distances on page 5.

EWM ESPRIT WALL MOUNT

1. Remove one or both knockouts from the conduit plate.

2. Using the plate as a template, mark the conduit and fastener positions on the mounting surface.

3. Prepare the mounting surface.

Figure 1. Conduit Plate Knockouts and Sealing Glands

4. Install conduit fittings (not supplied) or sealing glands (supplied) in the conduit plate (refer to Figure 1).

5. Attach the gasket (supplied) to the end of the EWM mount.

Figure 2. Attaching the Gasket to the EWM

6. Thread the wiring/cabling through the conduit plate/sealing glands and the EWM mount.

7. Use mounting hardware (not supplied) to secure the EWM to the mounting surface.

8. Refer to the manual supplied with the Esprit system to complete the installation.

C1356M-A (9/18) 3

EPM ESPRIT POLE MOUNT

1. Thread the wiring/cabling through the hole in the EPM mount.

2. Attach the mount to the pole with three stainless steel straps (supplied).

3. Remove one or both knockouts from the conduit plate (supplied with the EWM) (refer to Figure 1 on page 3).

4. Install conduit fittings (not supplied) or sealing glands (supplied with the EWM) in the conduit plate (refer to Figure 1 on page 3).

5. Attach the gasket (supplied with the EWM) to the end of the EWM mount (refer to Figure 2 on page 3).

6. Thread the wiring/cabling through the conduit plate/sealing glands and the EWM mount.

7. Use nuts, lock washers, and flat washers (supplied) to secure the EWM and the conduit plate to the EPM mount.

Figure 3. Securing the EWM to the EPM or ECM101

8. Refer to the manual supplied with the Esprit system to complete the installation.

ECM101 ESPRIT CORNER MOUNT

1. Using the ECM101 mount as a template, mark the fastener positions on the mounting surface.

2. Prepare the mounting surface.

3. Thread the wiring/cabling through the hole in the mount.

4. Use mounting hardware (not supplied) to secure the ECM101 to the mounting surface.

5. Remove one or both knockouts from the conduit plate (supplied with the EWM) (refer to Figure 1 on page 3).

6. Install conduit fittings or sealing glands (supplied with the EWM) in the conduit plate (refer to Figure 1 on page 3).

7. Attach the gasket (supplied with the EWM) to the end of the EWM mount (refer to Figure 2 on page 3).

8. Thread the wiring/cabling through the conduit plate/sealing glands and the EWM wall mount.

9. Use nuts, lock washers, and flat washers (supplied) to secure the EWM and the conduit plate to the ECM101 mount (refer to Figure 3).

10. Refer to the manual supplied with the Esprit system to complete the installation.

4 C1356M-A (9/18)

EPP2 ESPRIT PEDESTAL ADAPTER

1. Thread the wiring/cabling through the pedestal mount and the EPP2 pedestal adapter.

2. Use mounting hardware (not supplied) to secure the EPP2 to the pedestal adapter.

3. Complete the Esprit system installation following the instructions supplied with the equipment.

Figure 4. Attaching the EPP2 to a Pedestal Mount

VIDEO AND POWER CABLE WIRING DISTANCES

Table A lists the maximum video coaxial cable distances. Before installing any mount, make sure the distance from the Esprit to the head end is
less than the maximum distance for the coaxial cable.

Table A. Video Coaxial Cable Requirements

Cable Type* Maximum Distance

RG59/U* 750 ft (229 m)

RG6/U 1,000 ft (305 m)

RG11/U 1,500 ft (457 m)

*Cable requirements:

75-ohm impedance
All-copper center conductor
All-copper braided shield with 95 percent braid coverage

NOTE: The distance for Ethernet cables is 100 m (328 ft).

Table B lists the recommended maximum distances for 24 VAC applications and are calculated with a 10 percent voltage drop. (Ten percent is
generally the maximum allowable voltage drop for AC-powered devices.)

Table B. Wiring Distances (24 VAC)

Wire

Gauge

Maximum

Distance

20

2

(0.5 mm

)18(1.0 mm2)16(1.5 mm2)14(2.5 mm2)12(4.0 mm2)10(6.0 mm2)

40

(12)

64

(19)

102
(31)

163
(49)

258
(78)

411

(125)

C1356M-A (9/18) 5

Table C. Wiring Distances (48 VDC)

Wire

Gauge

Non-IR

Maximum

Distance

IR

20

(0.5 mm2)18(1.0 mm2)16(1.5 mm2)14(2.5 mm2)12(4.0 mm2)10(6.0 mm2)

158
(48)

103
(31)

251
(76)

164
(50)

398

(121)

261
(79)

634

(193)

415

(126)

1008
(307)

659

(201)

NOTES:

• Use a power source with a minimum of 100 VA.

• Wire gauges are standard AWG and metric sizes. Distances are calculated in feet; values in parentheses are meters.

1602
(488)

1048
(320)

REVISION HISTORY

Manual # Date Comments

C1356M 11/17 Original version.
C1356M-A 9/18 Changed ECM100 to ECM101

Pelco, the Pelco logo, and other trademarks associa ted with Pelco products referred to in this publication are trademarks of Pelco, Inc. or its affilia tes. © Copyright 2018, Pelco, Inc.
ONVIF and the ONVIF logo are trademarks of ONVIF Inc. All other product names and services are the property of their respective companies. All rights reserved.
Product specifications and availability are subject to change without notice.

6 C1356M-A (9/18)

Pelco, Inc. 625 W. Alluvial Ave., Fresno, California 93711 USA

USA & Canada Tel [phone] Fax [phone]

International Tel [phone] Fax [phone]

www.pelco.com