Pelco EM22 User Manual

INSTALLATION

EM22 Enclosure Mount

C227M-E (1/08)

Important Safety Instructions

Prior to installation and use of this product, the following WARNINGS should be observed.

1. Installation and servicing should be done only by qualified service personnel and conform to all local
codes.

2. Installation shall be done in accordance with all local and national electrical and mechanical codes
utilizing only approved materials.

3. Use only installation methods and materials capable of supporting four times the maximum
specified load.

4. Use stainless steel hardware to fasten the mount to outdoor surfaces.

5. To prevent damage from water leakage when installing a mount outdoors on a roof or wall, apply
sealant around the bolt holes between the mount and mounting surface.

The product and/or manual may bear the following marks:

This symbol indicates that dangerous voltage
constituting a risk of electric shock is present
within this unit.

This symbol indicates that there are important
operating and maintenance instructions in the
literature accompanying this unit.

CAUTION:

RISK OF ELECTRIC SHOCK.

DO NOT OPEN.

Description

The EM22 wall mount has been engineered for use with light- to medium-weight cameras and various
Pelco enclosures having a 2-inch mounting hole pattern.

The EM22 is designed to be mounted on a wall or any vertical surface and will support up to 40 lb (18 kg).
The mount also features a fully adjustable swivel head allowing 360 degrees horizontal movement.

Installation

The EM22 mount is supplied with two 1/4-20 x 0.625 hex head bolts for use in attaching the enclosure/
camera to the mount. The EM22 requires two fasteners to secure the mount to the mounting surface.
These fasteners are not supplied (minimum 1/4-inch diameter recommended).

If installing outdoors, stainless steel hardware is recommended.

To install the mount:

1. Drill holes in the mounting surface using the mount as a template, and then attach mount securely
with the required fasteners (not supplied).

WARNING: When installing the mount outdoors, seal the bolt holes with an appropriate
sealant to prevent water damage to the mounting surface. Apply the sealant around the bolt
holes between the mount and the mounting surface.

2. Attach the enclosure or camera securely to the mount with the two 1/4-20 hex head screws
(supplied).

3. Loosen the hex head bolts on the swivel head and adjust for pan rotation (360 degrees) and tilt angle
(75 degrees up or down). Retighten the bolts to lock the swivel head into place.

2 C227M-E (1/08)

Specifications

Pan Adjustment Unlimited 360°
Tilt Adjustment ±75° (up or down)
Construction Cast aluminum wall arm with aluminum adjustable head
Finish Gray polyester powder coat
Locking Method 3/8-16 hex head bolts
Enclosure Mounting 2 each: 1/4-20 mounting bolts, flat washers, and split washers

Suggested Mounting Method Secure to solid surface with 2 fasteners (minimum 1/4-inch

Maximum Load 40 lb (18 kg)
Weight 3.05 lb (1.39 kg)

2.00

3.40

(10.41)

1.74

(4.42)

(5.08)

3.00

(7.62)

1.50

(3.81)

Ø 0.27 (0.68), 7X

(supplied)

diameter recommended)

1.50 (3.81)

3.00

(7.62)

7.00

(17.78)

4.16

(10.62)

16.50

(41.91)

NOTE: VALUES IN PARENTHESES ARE CENTIMETERS;

ALL OTHERS ARE INCHES.

6.00

(15.24)

4.50

(11.43)

Ø 0.34 (0.86), 2X

(Design and product specifications subject to change without notice.)

REVISION HISTORY

Manual # Date Comments

C227M-D 3/99 Removed instructions for MM22 and created separate manual (C228M). Revised to new format.
C227M-E 1/08 Revised to new format. Revised mounting head hole pattern per ECO 07-17992.

Pelco, the Pelco logo, Camclosure, DigitalSENTRY, Endura, Esprit, ExSite, Genex, Intelli-M, Legacy, and Spectra are registered trademarks of Pelco, Inc.
Spectra III is a trademark of Pelco, Inc. © Copyright 2008, Pelco, Inc.
DLP is a registered trademark of Texas Instruments Incorporated. All rights reserved.

The materials used in the manufacture of this document and its components are compliant to the requirements of Directive 2002/95/EC.

C227M-E (1/08) 3

PRODUCT WARRANTY AND RETURN INFORMATION

WARRANTY

Pelco will repair or replace, without charge, an y merchandise proved defective in material or workmanship for a period of one year after the date of
shipment.

Exceptions to this warranty are as noted below:

• Five years on fiber optic products and TW3000 Series unshielded twisted pair (UTP) transmission products.

• Three years on Spectra® IV products.

• Three years on Genex® Series products (multiplexers, server, and keyboard).

• Three years on DX Series digital video recorders, DVR5100 Series digital video recorders, DigitalSENTRY® Series hardware products, DVX Series
digital video recorders, NVR300 Series netwo rk video recorders, and Endura® Series distributed network-based video products.

• Three years on Camclosure® and Pelco-branded fixed camera models, except the CC3701 H-2, CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2,
and MC3651H-2X camera models, which ha ve a five-year warranty.

• Three years on PMCL200/300/400 Series LCD monit ors.

• Two years on standard motorized or fixed focal length lenses.

• Two years on Legacy®, CM6700/CM6800/CM9700 Series matrix, and DF5/DF8 Series fixed dome products.

• Two years on Spectra III™, Spectra Mini, Esprit®, ExSite®, and PS20 scanners, including when used in continuous motion applications.

• Two years on Esprit and WW5700 Series window wiper (excluding wiper blades).

• Two years (except lamp and color wheel) on Digital Light Processing (DLP®) displays. The lamp and color wheel will be covered for a period of
90 days. The air filter is not covered un der warranty.

• Two years on Intelli-M® eIDC controllers.

• One year (except video heads) on video cassette recorders (VCRs). Video heads will be covered for a period of six months.

• Six months on all pan and tilts, scanners, or pre set lenses used in continuous motion applications (preset scan, tour, and auto scan modes).

Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco shipment. All goods requiring warranty repair shall be sent
freight prepaid to a Pelco designated locatio n. Repairs made necessary by reason of misuse, alteration, normal wear, or accident are no t covered under
this warranty.

Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from the specific use or application made of the Products. Pelco’s
liability for any claim, whether based on breach of contract, negligence, infringement of any rights of any party or product liability, relating to the
Products shall not exceed the price paid by the Dealer to Pelco for such Products. In no event will Pelco be liable for any special, incidental, or
consequential damages (including loss of use, loss of profit, and claims of third parties) however caused, whether by the negligence of Pelco or
otherwise.

The above warranty provides the Dealer with spe cific legal rights. The Dealer may also have additional right s, which are subject to variation from state
to state.

If a warranty repair is required, the Dealer must contact Pelco at [phone] or [phone] to obtain a Repair Authorization number (RA), and
provide the following information:

1. Model and serial number

2. Date of shipment, P.O. number, sales order number, or Pelco invoice number

3. Details of the defect or problem

If there is a dispute regarding the warranty of a product that does not fall un der the warranty conditions stated above, please include a written
explanation with the product wh en returned.

Method of return shipment shall be the same or equal to the method by which the item was received by Pelco.

RETURNS

To expedite parts returned for repair or credit, please call Pelco at [phone] or [phone] to obtain an authorization number (CA number if
returned for credit, and RA number if returned for repair) and designated return location.

All merchandise returned for credit may be subject to a 20 percent restocking and refurbishing charge.

Goods returned for repair or credit should be clearly identified with the assigned CA or RA number and freight should be prepaid.

Worldwide Headquarters • 3500 Pelco Way • Clovis, California 93612 USA • www.pelco.com

USA & Canada • Tel: [phone] • Fax: [phone]

International • Tel: [phone] • Fax: [phone]