Pelco EM1015U, EM1900U User Manual 2

C202M-B (4/99)
EM1009U/EM1015U/EM1900U
Enclosure Mounts

®

3500 Pelco Way,
Clovis, CA 93612-5699
USA

In North America & Canada:
Tel [phone]
FAX [phone]

International Customers:
Tel [phone]
FAX [phone]

www.pelco.com

U

®

L

LISTED

IMPORTANT SAFEGUARDS AND WARNINGS

Prior to installation and use of this product, the following WARNINGS should be observed.

1. Installation and servicing should only be done by qualified service and installation personnel.

2. Installation shall be done in accordance with all local and national electrical and mechani­cal codes utilizing only approved materials.

3. Use only installation methods and materials capable of supporting four times the maxi­mum specified load.

4. Use stainless steel hardware to fasten the mount to outdoor surfaces.

5. To prevent damage from water leakage when installing a mount outdoors on a roof or
wall, apply sealant around the bolt holes between the mount and mounting surface.

The product and/or manual may bear the following marks:

This symbol indicates that danger­ous voltage constituting a risk of
electric shock is present within
this unit.

This symbol indicates that there
are important operating and main­tenance instructions in the litera­ture accompanying this unit.

Please thoroughly familiarize yourself with the information in this manual prior to installation
and operation.

CAUTION:

RISK OF ELECTRIC SHOCK.

DO NOT OPEN.

DESCRIPTION

The EM1009U/EM1015U/EM1900U mounts are capable of supporting loads up to 40 pounds
(18 kg) and are designed for ceiling, pedestal, and wall applications. These versatile mounts
can be used with enclosures that have a 2-inch (5.08 cm) mounting hole pattern.

Constructed of aluminum, all three mounts feature a manually adjustable swivel head that al­lows 360-degree horizontal positioning of the enclosure. In addition, there is a 1-inch (2.54 cm)
diameter cable feedthrough hole and openings in the top and bottom to conceal the wiring.

Models

EM1009U Universal, medium-duty, pedestal/ceiling mount with manually adjustable

EM1015U Universal, medium-duty, pedestal/ceiling mount with manually adjustable

EM1900U Universal, medium-duty, 90-degree wall mount with manually adjustable

swivel head. Mount extends 10.66 inches (27.08 cm) from wall or ceiling.

swivel head. Mount extends 16.66 inches (42.32 cm) from wall or ceiling.

swivel head. Mount extends 14.98 inches (38.05 cm) from wall or ceiling.

INSTALLATION

To attach the mount, perform the following steps:

CAUTION:

Make
certain that the mount­ing surface is capable

of supporting four times the full
load of the mount, enclosure,
and camera.

1. Determine the location where the mount is to be installed.

2. Using the mount as a template, mark and drill holes in the mounting surface.

3. Bring the wiring in from the cable hole in the mounting plate or the side of the mount near
the mounting plate and through the mount arm.

4. Attach the mount securely with four 1/4-20 fasteners (not provided) of appropriate length.
When installing the mount outdoors, seal the mounting holes with an appropriate sealant.
Apply the sealant around the holes between the mount and the mounting surface.

5. Attach the enclosure or camera securely with the two 1/4-20 x 0.625-inch (1.588 cm) hex
bolts provided.

6. Loosen the bolts on the swivel head and position as desired. Tighten bolts and lock into
place.

7. Make all necessary electrical connections to the enclosure and camera (refer to the
manuals provided with the enclosure and camera.)

SERVICE MANUAL

If you need replacement parts, obtain a service manual in one of the following ways:

• Go to Pelco’s web site at ftp://www.pelco.com and find service manual C202SM.

• Contact Pelco’s Literature Department and request service manual C202SM.