Pelco EM1015U, EM1900U User Manual

INSTALLATION

EM1009U/EM1015U/
EM1900U
Enclosure Mounts

C202M-C (1/08)

IMPORTANT SAFETY INSTRUCTIONS

1. Installation and servicing should only be done by qualified service and installation personnel.

2. Installation shall be done in accordance with all local and national electrical and mechanical codes
utilizing only approved materials.

3. Use only installation methods and materials capable of supporting four times the maximum
specified load.

4. Use stainless steel hardware to fasten the mount to outdoor surfaces.

5. To prevent damage from water leakage when installing a mount outdoors on a roof or wall, apply
sealant around the bolt holes between the mount and mounting surface.

The product and/or manual may bear the following marks:

This symbol indicates that dangerous voltage
constituting a risk of electric shock is present within
this unit.

This symbol indicates that there are important
operating and maintenance instructions in the
literature accompanying this unit.

CAUTION:

RISK OF ELECTRIC SHOCK.

DO NOT OPEN.

DESCRIPTION

The EM1009U/EM1015U/EM1900U mounts are capable of supporting loads up to 40 lb (18 kg) and are
designed for ceiling, pedestal, and wall applications. These versatile mounts can be used with enclosures
that have a 2-inch (5.08 cm) mounting hole pattern.

Constructed of aluminum, all three mounts feature a manually adjustable swivel head that allows
360-degree horizontal positioning of the enclosure. In addition, there is a 1-inch (2.54 cm) diameter cable
feedthrough hole and openings in the top and bottom to conceal the wiring.

MODELS

EM1009U Universal, medium-duty, pedestal/ceiling mount with manually adjustable swivel head.

EM1015U Universal, medium-duty, pedestal/ceiling mount with manually adjustable swivel head.

EM1900U Universal, medium-duty, 90-degree wall mount with manually adjustable swivel head.

2 C202M-C (1/08)

Mount extends 9.80 inches (24.89 cm) from wall or ceiling.

Mount extends 15.80 inches (40.13 cm) from wall or ceiling.

Mount extends 15.03 inches (38.18 cm) from wall or ceiling.

INSTALLATION

To attach the mount, perform the following steps:

1. Determine the location where the mount is to be installed.

WARNING: Make certain that the mounting surface is capable of supporting four times the full
load of the mount, enclosure, and camera.

2. Using the mount as a template, mark and drill holes in the mounting surface.

3. Pull the wiring from the cable hole in either the mounting plate or the side of the mount near the
mounting plate. Then pull the wiring through the mount arm.

4. Attach the mount securely with four 1/4-20 fasteners (not provided) of appropriate length. When
installing the mount outdoors, seal the mounting holes with an appropriate sealant. Apply the
sealant around the holes located between the mount and the mounting surface.

5. Attach the enclosure or camera securely with the two 1/4-20 x 0.625-inch (1.588 cm) hex bolts
provided.

6. Loosen the bolts on the swivel head and position as desired. Tighten bolts and lock into place.

7. Make all necessary electrical connections to the enclosure and camera (refer to the manuals
provided with the enclosure and camera.)

SERVICE MANUAL

If you need replacement parts, obtain a service manual in one of the following ways:

• Go to Pelco’s Web site at ftp://www.pelco.com and find service manual C202SM-A.

• Contact Pelco’s Literature Department and request service manual C202SM-A.

C202M-C (1/08) 3

SPECIFICATIONS

Construction Aluminum
Finish Gray polyester powder coat
Maximum Load 40 lb (18 kg)
Pan Adjustment 360°
Tilt Adjustment ±75°
Locking Method 3/8-16 hex bolts
Enclosure Mounting 2, 1/4-20 x 0.625-inch (1.588 cm) hex bolts (provided)
Suggested Mounting Method Secure to solid surface with four 1/4-20 fasteners (not provided)
Unit Weight

EM1009U 1.98 lb (0.90 kg)
EM1015U 2.43 lb (1.10 kg)
EM1900U 2.83 lb (1.28 kg)

(Design and product specifications subject to change without notice.)

1.00 (2.54)

1.00

(2.54)

4.10 (10.41)

Ø 6.00 (15.24)

3.43

(8.71)

EM1009U

9.80 (24.89)

EM1015U

15.80 (40.13)

3.00

(7.62)

Ø 1.00

(2.54)

EM1009U/EM10150

4 C202M-C (1/08)

14.16

(37.11)

Ø 6.00
(15.24)

3.43

(8.71)

4.10

(10.41)

EM1900U

1.00 (2.54)

1.00 (2.54)

15.03 (38.18)

Ø1.00 (2.54)

NOTE: VALUES IN PARENTHESES ARE CENTIMETERS; ALL OTHERS ARE INCHES

C202M-C (1/08) 5

C
C

t

C
C

c.

.

.

The materials used in the manufacture of this document and its components are compliant to the
requirements of Directive 2002/95/EC.

REVISION HISTORY

Manual # Date Comments

202M 4/91 Original version.
202M-A 2/98 Improved, stronger versions of the mounts per ECO97-429 and ECO 97-450. Changed manual to new forma

202M-B 4/99 Removed Figure 1 and Table A and created separate service manual. Revised to new format.
202M-C 1/08 Revised dimension drawings to reflect new mounting head hole pattern per ECO07-17992.

Pelco, the Pelco logo, Camclosure, DigitalSENTRY, Endura, Esprit, ExSite, Genex, Intelli-M, Legacy, and Spectra are registered trademarks of Pelco, In
Spectra III is a trademark of Pelco, Inc. © Copyright 2008, Pelco, Inc
DLP is a registered trademark of Texas Instruments, Incorporated. All rights reserved

6 C202M-C (1/08)

and manual pagination.

PRODUCT WARRANTY AND RETURN INFORMATION

WARRANTY

Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of
shipment.

Exceptions to this warranty are as noted below:

• Five years on fiber optic products and TW3000 Series unshielded twisted pair (UTP) transmission products.

• Three years on Spectra® IV products.

• Three years on Genex® Series products (multiplexers, server, and keyboard).

• Three years on DX Series digital video recorders, DVR51 00 Seri es digital vide o reco rders, Dig italSE NTRY® Series hardware products, DVX Series
digital video recorders, NVR300 Series network video recorders, and Endura® Series distributed network-based video products.

• Three years on Camclosure® and Pelco-branded fixed camera models, except the CC3701H-2, CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2,
and MC3651H-2X camera models, which have a five-year warranty.

• Three years on PMCL200/300/400 Series LCD monitors.

• Two years on standard motorized or fixed focal length lenses.

• Two years on Legacy®, CM6700/CM6800/CM9700 Series matrix, and DF5/DF8 Series fixed dome products.

• Two years on Spectra III™, Spectra Mini, Esprit®, ExSite®, and PS20 scanners, including when used in continuous motion applications.

• Two years on Esprit and WW5700 Series window wiper (excluding wiper blades).

• Two years (except lamp and color wheel) on Digital Light Proce ssing (DLP®) displays. The lamp and color wheel will be covered for a period of
90 days. The air filter is not covered under warranty.

• Two years on Intelli-M® eIDC controllers.

• One year (except video heads) on video cassette recorders (VCRs). Video heads will be covered for a period of six months.

• Six months on all pan and tilts, scanners, or preset lenses used in continuous motion applications (preset scan, tour, and auto scan modes).

Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco shipment. All goods requiring warranty repair shall be sent
freight prepaid to a Pelco designated location. Repairs made necessary by reason of misuse, alteration, normal wear, or accident are not covered under
this warranty.

Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from the specific use or application made of the Products. Pelco’s
liability for any claim, whether based on breach of contract, negligence, infringement of any rights of any party or product liability, relating to the
Products shall not exceed the price paid by the Dealer to Pelco for such Products. In no event will Pelco be liable for any special, incidental, or
consequential damages (including loss of use, loss of profit, and claims of third parties) however caused, whether by the negligence of Pelco or
otherwise.

The above warranty provides the Dealer with specific legal rights. The Dealer may also have additional rights, which are subject to variation from state
to state.

If a warranty repair is require d, the De aler m ust co ntact P elco at (800 ) 289-9100 or [phone] to obtain a Repair Auth oriza ti on number (RA), and
provide the following information:

1. Model and serial number

2. Date of shipment, P.O. number, sales order number, or Pelco invoice number

3. Details of the defect or problem

If there is a dispute regarding the warranty of a product that does not fall un der the warranty conditions stated above, please include a wri tten
explanation with the product when returned.

Method of return shipment shall be the same or equal to the method by which the item was received by Pelco.

RETURNS

To expedite parts returned for repair or credit, please call Pelco at (800 ) 289-9100 or [phone] to obtain an authorization number (CA number if
returned for credit, and RA number if returned for repair) and designated return location.

All merchandise returned for credit may be subject to a 20 percent restocking and refurbishing charge.
Goods returned for repair or credit should be clearly identified with the assigned CA or RA number and freight should be prepaid.

Worldwide Headquarters

3500 Pelco Way

Clovis, California 93612 USA

USA & Canada

Tel: [phone]

Fax: [phone]

International

Tel: [phone]

Fax: [phone]

www.pelco.com

ISO9001

Australia|Canada|Finland|France|Germany|Italy|Macau|The Netherlands|Russia|Singapore

South Africa

Spain|Sweden|United ArabEmirates|United Kingdom|United States

|