Pelco EHX4EORKIT, EHX6EORKIT, EHX8EORKIT User Manual

EHX*EORKIT O-Ring Replacement Kit

SUPPLIED PARTS

The EHX*EORKIT O-ring replacement kit for EHX*E Series explosion-proof camera enclosures contains:

Qty Description

1 O-ring (used for the rear plate seal only)
1 Tube of O-ring lubricant
2 Bags of desiccant
4 M6 x 25 mm rear plate attaching screws

NOTE: Four spare M6 x 25 mm screws are included in the O-ring kit to replace any lost or damaged rear cover screws.

USER-SUPPLIED PARTS

Pelco does not supply basic tools needed for the installation process. The following tools are recommended:

• 5-mm Allen wrench

• Flat screwdriver

APPLICABLE MODELS

This installation instruction applies to the following O-ring kits and enclosure models:

INSTALLATION

C1954M-A (4/13)

O-Ring Kit Enclosure Model

EHX4EORKIT EHX4E
EHX6EORKIT EHX6E/EHX6E-16
EHX8EORKIT EHX8E

WARNINGS:

• Do not remove the front cover. If front cover is removed, Pelco cannot be held responsible for the loss of explosion-proof rating, UL listing, or

ability of the enclosure to contain an explosion.

• Potential electrostatic charging hazard. Clean the enclosure surface by gently wiping it with a damp, lint-free cloth before handling or

performing maintenance.

REPLACING THE O-RING

1. Turn off power to the enclosure.

2. Remove the 12 or 16 screws (depending upon the enclosure model) that attach the rear plate to the enclosure.

3. Disconnect the video and electrical cables inside the enclosure.

4. Remove the desiccant bags inside the enclosure and replace them with the two bags from the kit.

5. Remove the O-ring from the groove in the enclosure rear plate and discard. Be careful not to damage or score the O-ring groove. Clean the O-ring
groove thoroughly.

6. Lubricate the new O-ring with the lubricant in the kit and install it in the groove in the enclosure rear plate.

7. Reconnect the video and electrical cables.

8. Reinstall the rear plate on the rear of the enclosure body. Apply additional lubricant to the new O-ring, if necessary, and ensure it remains in the correct
position. Reinstall the screws finger tight.

9. Tighten the rear plate attaching screws in a star pattern.

PRODUCT WARRANTY AND RETURN INFORMATION

WARRANTY

Pelco will repair or replace, without charge, any merchandise proved defective in
material or workmanship for a period of one year after the date of shipment.

Exceptions to this warranty are as noted below:

• Five years:
– Fiber optic products
– Unshielded Twisted Pair (UTP) transmission products
– CC3701H-2, CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2, and

MC3651H-2X camera models

• Three years:
– FD Series and BU Series analog camera models
– Fixed network cameras and network dome cameras with Sarix
– Sarix thermal imaging products (TI and ESTI Series)
– Fixed analog camera models (C20 Series, CCC1390H Series, C10DN Series,

and C10CH Series)
– EH1500 Series enclosures
– Spectra
– Spectra HD dome products
– Camclosure

®

IV products (including Spectra IV IP)

®

IS Series integrated camera systems

– DX Series video recorders (except DX9000 Series which is covered for a

period of one year), DVR5100 Series digital video recorders, Digital Sentry

Series hardware products, DVX Series digital video recorders, and NVR300

Series network video recorders

®

– Endura
– Genex

Series distributed network-based video products

®

Series products (multiplexers, server, and keyboard)
– PMCL200/300/400 Series LCD monitors
– PMCL5xxF Series and PMCL5xxNB Series LCD monitors
– PMCL5xxxBL Series LED monitors

• Two years:
– Standard varifocal, fixed focal, and motorized zoom lenses
– DF5/DF8 Series fixed dome products

®

– Legacy
– Spectra III

Series integrated positioning systems

™

, Spectra Mini, Spectra Mini IP, Esprit®, ExSite®, ExSite IP, and

PS20 scanners, including when used in continuous motion applications
– Esprit Ti and TI2500 Series thermal imaging products
– Esprit and WW5700 Series window wiper (excluding wiper blades)
– CM6700/CM6800/CM9700 Series matrix
– Digital Light Processing (DLP

®

) displays (except lamp and color wheel). The
lamp and color wheel will be covered for a period of 90 days. The air filter is
not covered under warranty.

®

technology

•Six months:
– All pan and tilts, scanners, or preset lenses used in continuous motion

applications (preset scan, tour, and auto scan modes)

Pelco will warrant all replacement parts and repairs for 90 days from the date of
Pelco shipment. All goods requiring warranty repair shall be sent freight prepaid
to a Pelco designated location. Repairs made necessary by reason of misuse,
alteration, normal wear, or accident are not covered under this warranty.

Pelco assumes no risk and shall be subject to no liability for damages or loss
resulting from the specific use or application made of the Products. Pelco’s liability
for any claim, whether based on breach of contract, negligence, infringement of
any rights of any party or product liability, relating to the Products shall not exceed
the price paid by the Dealer to Pelco for such Products. In no event will Pelco be
liable for any special, incidental, or consequential damages (including loss of use,
loss of profit, and claims of third parties) however caused, whether by the
negligence of Pelco or otherwise.

The above warranty provides the Dealer with specific legal rights. The Dealer may
also have additional rights, which are subject to variation from state to state.

If a warranty repair is required, the Dealer must contact Pelco at [phone] or
[phone] to obtain a Repair Authorization number (RA), and provide the

®

following information:

1. Model and serial number

2. Date of shipment, P.O. number, sales order number, or Pelco invoice number

3. Details of the defect or problem

If there is a dispute regarding the warranty of a product that does not fall under
the warranty conditions stated above, please include a written explanation with
the product when returned.

Method of return shipment shall be the same or equal to the method by which the
item was received by Pelco.

RETURNS

To expedite parts returned for repair or credit, please call Pelco at [phone]
or [phone] to obtain an authorization number (CA number if returned for
credit, and RA number if returned for repair) and designated return location.

All merchandise returned for credit may be subject to a 20 percent restocking and
refurbishing charge.

Goods returned for repair or credit should be clearly identified with the assigned
CA or RA number and freight should be prepaid.

Revised 10-9-12

REVISION HISTORY

Manual # Date Comments

C1954M 11/98 Original version.
C1954M-A 4/13 Updated format and warranty.

Pelco, the Pelco logo, and other trademarks a ssociated with Pelco products referred to in this publication are trademarks of P elco, Inc. or its affiliat es. © Copyright 2013, Pelco, Inc.
ONVIF and the ONVIF logo are trademarks of ONVIF Inc. All other product names and services are the property of their respective companies. All rights reserved.
Product specifications and availability are subje ct to change without notice.

Pelco by Schneider Electric 3500 Pelco Way Clovis, California 93612-5699 United States

USA & Canada Tel [phone] Fax [phone]

International Tel [phone] Fax [phone]

www.pelco.com www.pelco.com/community