Pelco EH8008ORKIT User Manual 2

EH8006ORKIT and EH8008ORKIT
O-Ring Replacement Kits for
EH8106 and EH8108 Series
Pressurized Camera Enclosures
Installation Instructions
C1952M (11/98)

®

1.0 INSTALLATION

WARNING:

must be released before
opening the enclosure or
personal injury may
result.

NOTE:

The kit contains two O-rings.

The second one is a spare.

NOTE:

The EH8000RKIT recharge
kit uses a regulator that has a fixed,
nonadjustable output pressure of
5 psi. The gauge reads the tank pres­sure only. This can be used to deter­mine how much pressure is left in the
tank after each recharge and when it
is necessary to replace the tank.

CAUTION:

ing equipment other than
the EH8000RKIT re­charge kit is used, do not
exceed 5 psi. Exceeding

5 psi pressure will
damage the enclosure.

TIP:

Having the window of the
enclosure pointing upward will greatly
reduce the purge time necessary to
remove oxygen from the enclosure.

Pressure

If recharg-

1. Turn off power to the enclosure.

2. Remove the mating connector from the rear of the enclosure by turning the
outer ring counterclockwise until a click is felt; then pull the mating portion of
the connector off. You may elect to remove the enclosure from its mount which
will make the disassembly process much easier.

3. Remove the Schraeder valve cap.

4. Relieve internal enclosure pressure by depressing and holding down the center
stem of the Schraeder valve.

5. Once the internal pressure has been relieved, use a screwdriver to pry the
end of the spiral retaining ring from the retaining ring groove in the rear of the
enclosure body and remove the ring.

6. Pull the T-handle to remove the rear plate from the housing.

7. Remove the desiccant bags inside the enclosure and replace them with the
two bags from the kit.

8. Remove the O-ring from the groove in the enclosure rear plate and discard.
Be careful not to damage or score the O-ring groove. Clean the O-ring groove
thoroughly.

9. Lubricate the new O-ring with the lubricant in the kit and install it in the groove
in the enclosure rear plate.

10. Place the rear plate into the rear of the enclosure body. Apply additional lubricant
to the new O-ring, if necessary, and ensure it remains in the correct position.

11. Reinstall the spiral retaining ring in the retaining ring groove in the rear of the
enclosure.

12. Pressurize the inside of the enclosure using the EH8000RKIT recharge kit.
Connect the regulator to the tank by threading the nut into the socket of the
tank valve and tighten with a wrench. The regulator is preset for 5 psi. Exceeding

5 psi pressure will damage the enclosure.

13. Once the regulator has been attached to the tank, open the regulator valve
fully, then open the tank valve.

14. Using the self-holding air chuck, apply pressure to the enclosure by affixing
the air chuck to the Schraeder valve on the rear of the enclosure.

15. Remove the plastic cap from the pressure relief valve on the rear of the enclosure.
(Use a small flat screwdriver to hold it open.) At this point, allow the nitrogen to
flow through the enclosure until the humidity indicator registers the lowest humidity
level (changing color from pink to blue). The humidity indicator can be viewed
through the front window of the enclosure looking at the inside top of the enclosure.
Once the humidity indicator registers the lowest level, remove the screwdriver
and allow nitrogen to continue to flow into the enclosure until you no longer hear
the flow of nitrogen from the tank to the enclosure.

16. Remove the air chuck from the Schraeder valve and reinstall the valve cap.
Reinstall the plastic cap on the pressure relief valve. The enclosure is ready
for service.

Pelco • 3500 Pelco Way • Clovis, CA 93612-5699 • USA • www.pelco.com

In North America and Canada: Tel [phone] • FAX [phone]

International Customers: Tel [phone] or FAX [phone]

2.0 WARRANTY AND
RETURN INFORMATION

Pelco, the Pelco logo, Camclosure, Esprit,
Genex, Legacy, and Spectra are registered
trademarks of Pelco.
Endura and ExSite are trademarks of Pelco.

©Copyright 1998, Pelco. All rights reserved.

WARRANTY

Pelco will repair or replace, without charge, any merchandise proved defective in material or
workmanship for a period of one year after the date of shipment.

Exceptions to this warranty are as noted below:

• Five years on FT/FR8000 Series fiber optic products.

• Three years on Genex

• Three years on Camclosure
CC3751H-2, CC3651H-2X, MC3651H-2, and MC3651H-2X camera models, which have a five­year warranty.

• Two years on standard motorized or fixed focal length lenses.

• Two years on Legacy
dome products.

• Two years on Spectra
continuous motion applications.

• Two years on Esprit

• Eighteen months on DX Series digital video recorders, NVR300 Series network video

recorders, and Endura

®

Series products (multiplexers, server, and keyboard).

®

and fixed camera models, except the CC3701H-2, CC3701H-2X,

®

, CM6700/CM6800/CM9700 Series matrix, and DF5/DF8 Series fixed

®

, Esprit®, ExSite™, and PS20 scanners, including when used in

®

and WW5700 Series window wiper (excluding wiper blades).

™

Series distributed network-based video products.

• One year (except video heads) on video cassette recorders (VCRs). Video heads will be
covered for a period of six months.

• Six months on all pan and tilts, scanners or preset lenses used in continuous motion applications
(that is, preset scan, tour and auto scan modes).

Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco shipment.
All goods requiring warranty repair shall be sent freight prepaid to Pelco, Clovis, California. Repairs
made necessary by reason of misuse, alteration, normal wear, or accident are not covered under
this warranty.

Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from the
specific use or application made of the Products. Pelco’s liability for any claim, whether based on
breach of contract, negligence, infringement of any rights of any party or product liability, relating
to the Products shall not exceed the price paid by the Dealer to Pelco for such Products. In no event
will Pelco be liable for any special, incidental or consequential damages (including loss of use, loss
of profit and claims of third parties) however caused, whether by the negligence of Pelco or
otherwise.

The above warranty provides the Dealer with specific legal rights. The Dealer may also have
additional rights, which are subject to variation from state to state.

If a warranty repair is required, the Dealer must contact Pelco at [phone] or [phone]
to obtain a Repair Authorization number (RA), and provide the following information:

1. Model and serial number

2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number

3. Details of the defect or problem

If there is a dispute regarding the warranty of a product which does not fall under the warranty
conditions stated above, please include a written explanation with the product when returned.
Method of return shipment shall be the same or equal to the method by which the item was received
by Pelco.

RETURNS

In order to expedite parts returned to the factory for repair or credit, please call the factory at (800)
289-9100 or [phone] to obtain an authorization number (CA number if returned for credit,
and RA number if returned for repair).

All merchandise returned for credit may be subject to a 20% restocking and refurbishing charge.
Goods returned for repair or credit should be clearly identified with the assigned CA or RA number

and freight should be prepaid. Ship to the appropriate address below.
If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico, send goods to:

Service Department
Pelco
3500 Pelco Way
Clovis, CA 93612-5699

If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico and are instructed
to return goods to the USA, you may do one of the following:
If the goods are to be sent by a COURIER SERVICE, send the goods to:

Pelco
3500 Pelco Way
Clovis, CA 93612-5699 USA

If the goods are to be sent by a FREIGHT FORWARDER, send the goods to:

Pelco c/o Expeditors
473 Eccles Avenue
South San Francisco, CA 94080 USA
Phone: [phone]
Fax: [phone]

2 Pelco Manual C1952M (11/98)