Pelco EH2512, EH2515 User Manual

®

EH2500 Series

Dust-Tight Enclosure

Maintenance/

Service Manual

C1473SM-B (9/04)

Pelco • 3500 Pelco Way • Clovis, CA 93612-5699 USA • www.pelco.com
In North America and Canada: Tel [phone] • FAX [phone]

International Customers: Tel [phone] • FAX [phone]

CONTENTS

LIST OF ILLUSTRATIONS

LIST OF TABLES

Section Page

IMPORTANT SAFEGUARDS AND WARNINGS ................................................................3

DESCRIPTION ................................................................................................................... 4

MODELS ....................................................................................................................4

MAINTENANCE ................................................................................................................. 4

EXPLODED ASSEMBLY DIAGRAMS ................................................................................ 5

WARRANTY AND RETURN INFORMATION .................................................................... 8

Figure Page

1 EH2500 Series Exploded Assembly Diagram .................................................... 5

2 EH2500 Series Wiring Diagram ......................................................................... 7

Table Page

A EH2500 Series Exploded Assembly Parts List .................................................. 6

B EH2500 Series Wiring Diagram Parts List .........................................................7

2 Pelco Manual C1473SM-B (9/04)

IMPORTANT SAFEGUARDS AND WARNINGS

Prior to installation and use of this product, the following WARNINGS should be observed.

1. Installation and servicing should only be done by qualified service personnel and con­form to all local codes.

2. Unless the unit is specifically marked as a NEMA Type 3, 3R, 3S, 4, 4X ,6 or 6P enclo­sure, it is designed for indoor use only and it must not be installed where exposed to
rain and moisture.

3. Only use replacement parts recommended by Pelco.

4. After replacement/repair of this unit’s electrical components, conduct a resistance
measurement between line and exposed parts to verify the exposed parts have not
been connected to line circuitry.

5. The installation method and materials should be capable of supporting four times the
weight of the unit and equipment.

The product and/or manual may bear the following marks:

This symbol indicates that dangerous volt­age constituting a risk of electric shock is
present within this unit.

This symbol indicates that there are impor­tant operating and maintenance instructions
in the literature accompanying this unit.

Please thoroughly familiarize yourself with the information in this manual prior to installation
and operation.

CAUTION:

RISK OF ELECTRIC SHOCK.

DO NOT OPEN.

Pelco Manual C1473SM-B (9/04) 3

DESCRIPTION

The EH2500 Series enclosures are sealed, dust-tight and waterproof camera enclosures designed
to protect a CCTV camera and lens from adverse environmental conditions.

The enclosures feature a sled for camera mounting and a “T” handle on the rear plate to assist in
removing the back plate during installation and servicing.

All models will accept CCD cameras with fixed focal length or motorized zoom lenses.

MODELS

EH2508 6.25” L x 2.75” W x 2.75” H (15.88 x 6.99 x 6.99 cm)

EH2508-1/-2/-3 5.25” L x 2.75” W x 2.75” H (13.44 x 6.99 x 6.99 cm), 120/24/230 VAC heater

EH2512 10.25” L x 2.75” W x 2.75” H (26.04 x 6.99 x 6.99 cm)

EH2512-1/-2/-3 9.25” L x 2.75” W x 2.75” H (23.50 x 6.99 x 6.99 cm), 120/24/230 VAC heater

EH2515 13.25” L x 2.75” W x 2.75” H (33.66 x 6.99 x 6.99 cm)

EH2515-1/-2/-3 12.25” L x 2.75” W x 2.75” H (31.12 x 6.99 x 6.99 cm), 120/24/230 VAC heater

MAINTENANCE

Regularly scheduled maintenance is not required. Clean the outer surface of the enclosure with a
nonabrasive cleaning cloth and antistatic cleaner. Clean the viewing window with mild nonabrasive
soap and water to maintain picture clarity. Do not use kerosene or similar substances that may
damage the surface.

4 Pelco Manual C1473SM-B (9/04)

EXPLODED ASSEMBLY DIAGRAMS

17

18

19

24 2X

20 2X

21 2X

23

22 *

25

26 4X

12 *6X

4

5 2X

6

1

3 *

9 *

2X 15

8 *

13 2X*

Figure 1. EH2500 Series Exploded Assembly Diagram

2

7

16

*Available only with
models that have heaters

10 2X

11 2X

Pelco Manual C1473SM-B (9/04) 5

Table A. EH2500 Series Exploded Assembly Parts List

Item Qty Description Part Number

11Camera sled, EH2508 EH2584300COMP

1 Camera sled, EH2512 EH25124300COMP

1 Camera sled, EH2515 EH25154300COMP

21T-handle EH2584202COMP

31Terminal bracket EH2584901COMP

41Rear plate EH2584902COMP

52Liquid-tight fitting HF00-1300-3500

61Thermostat EH5510049A

71Self-sealing fastener, 10-24 x .750" EHP10001

81Thermostat TH01-8570-0100

91Terminal block, 4-position TRB323HDS-04

10 2 Screw, 6-32 x 5/8", button head, captive ZH00-0213-0709

11 2 Nylon washer, #6 ZH150X310X32N

12 6 4-40 x 1/4", Phillips pan head screw and lock washer ZH01-2001-0403

13 2 4-40 x 3/8", Phillips pan head screw and lock washer ZH01-2001-0405

14 N/A ZH4LWSIS

15 2 Screw, 6-32 x 5/8", socket head cap ZH6-32X.625CS

16 1 O-ring ZH69-0205-2404

17 1 Housing, EH2508 EH2584102COMP

1 Housing, EH2512 EH25124102COMP

1 Housing, EH2515 EH25154102COMP

18 1 Window EH2584501COMP

19 1 Cosmetic decal OL01-0023-0001

20 2 Screw, captive, 6-32 x 5/8", button head, socket ZH00-0213-0709

21 2 Nylon washer, #6 ZH150X310X32N

22 1 Dual-element window heater, 120 VAC HT01-0012-0204

1 Dual-element window heater, 24 VAC HT01-0022-0204

1 Dual-element window heater, 230 VAC HT01-0032-0204

23 1 O-ring ZH69-0205-2404

24 2 Pelco label LBLG10020

25 1 Mount EH2584200COMP

26 4 Screw, 8-32 x 3/8", button head, hex socket ZH01-0401-0805

6 Pelco Manual C1473SM-B (9/04)

INPUT

POWER

ENCLOSURE

TERMINAL 4 (AC LOW)

{

TERMINAL 3 (AC HIGH)

INPUT

POWER

CAMERA

7

11

13

TERMINAL 2

{

TERMINAL 1

6

4

PIN 2

PIN 1

9

12

PIN 1

PIN 2
PIN 3

PIN 1 RED WIRE (NEUTRAL)

PIN 2 BLACK WIRE
PIN 3 WHITE WIRE

HEATING
ELEMENT

{

POWER

5

1

4

3

CAMERA

POWER

Figure 2. EH2500 Series Wiring Diagram

Table B. EH2500 Series Wiring Diagram Parts List

Item Qty Description Part Number

11 Connector, 3-pin plug CON1-480303-0

21 Connector, 3-pin cap CON1-480305-0

31 Connector, 2-pin plug (camera power) CON1-480318-0

41 Connector, 2-pin cap CON1-480319-0

51 Dual-element window heater,120 VAC HT71-0012-204

1 Dual-element window heater, 24 VAC HT72-0022-204

1 Dual-element window heater, 230 VAC HT73-0032-204

61 Terminal bracket EH2584901COMP

71 Thermostat EH5510049A

81 Thermostat TH01-8570-0100

91 Terminal block, 4-position TRB323HDS-04

10 N/A ZH4LWSIS

11 4 4-40 x 1/4",

12 2 4-40 x 3/8",

13 2 Screw, 6-32 x 5/8", socket head, cap ZH6-32X.625CS

-- 1 6-32 thumbnut (not shown) ZH6-32THUMNUT

{

PIN 1

PIN 2

Phillips pan head screw and lock washer

Phillips pan head screw and lock washer

ZH01-2001-0403

ZH01-2001-0405

Pelco Manual C1473SM-B (9/04) 7

PRODUCT WARRANTY AND RETURN INFORMATION

WARRANTY

Pelco will repair or replace, without charge, any merchandise proved defective in material or
workmanship for a period of one year after the date of shipment.

Exceptions to this warranty are as noted below:

• Five years on FT/FR8000 Series fiber optic products.

®

• Three years on Genex

• Three years on Camclosure® and fixed camera models, except the CC3701H-2,
CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2, and MC3651H-2X camera models,
which have a five-year warranty.

•Two years on standard motorized or fixed focal length lenses.

•Two years on Legacy
fixed dome products.

•Two years on Spectra
continuous motion applications.

•Two years on Esprit

• Eighteen months on DX Series digital video recorders, NVR300 Series network video
recorders, and Endura

• One year (except video heads) on video cassette recorders (VCRs). Video heads will be
covered for a period of six months.

• Six months on all pan and tilts, scanners or preset lenses used in continuous motion
applications (that is, preset scan, tour and auto scan modes).

Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco
shipment. All goods requiring warranty repair shall be sent freight prepaid to Pelco, Clovis,
California. Repairs made necessary by reason of misuse, alteration, normal wear, or accident
are not covered under this warranty.

Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from
the specific use or application made of the Products. Pelco’s liability for any claim, whether
based on breach of contract, negligence, infringement of any rights of any party or product
liability, relating to the Products shall not exceed the price paid by the Dealer to Pelco for
such Products. In no event will Pelco be liable for any special, incidental or consequential
damages (including loss of use, loss of profit and claims of third parties) however caused,
whether by the negligence of Pelco or otherwise.

The above warranty provides the Dealer with specific legal rights. The Dealer may also have
additional rights, which are subject to variation from state to state.

Series products (multiplexers, server, and keyboard).

®

, CM6700/CM6800/CM9700 Series matrix, and DF5/DF8 Series

®

, Esprit®, ExSite™, and PS20 scanners, including when used in

®

and WW5700 Series window wiper (excluding wiper blades).

™

Series distributed network-based video products.

If a warranty repair is required, the Dealer must contact Pelco at [phone] or
[phone] to obtain a Repair Authorization number (RA), and provide the following
information:

1. Model and serial number

2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number

3. Details of the defect or problem

If there is a dispute regarding the warranty of a product which does not fall under the
warranty conditions stated above, please include a written explanation with the product
when returned.

Method of return shipment shall be the same or equal to the method by which the item was
received by Pelco.

RETURNS

In order to expedite parts returned to the factory for repair or credit, please call the factory at
[phone] or [phone] to obtain an authorization number (CA number if returned
for credit, and RA number if returned for repair).

All merchandise returned for credit may be subject to a 20% restocking and refurbishing
charge.

Goods returned for repair or credit should be clearly identified with the assigned CA or RA
number and freight should be prepaid. Ship to the appropriate address below.

If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico, send goods to:

Service Department
Pelco
3500 Pelco Way
Clovis, CA 93612-5699

If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico and are
instructed to return goods to the USA, you may do one of the following:

If the goods are to be sent by a COURIER SERVICE, send the goods to:

Pelco
3500 Pelco Way
Clovis, CA 93612-5699 USA

If the goods are to be sent by a FREIGHT FORWARDER, send the goods to:

Pelco c/o Expeditors
473 Eccles Avenue
South San Francisco, CA 94080 USA
Phone: [phone]
Fax: [phone]

REVISION HISTORY

Manual # Date Comments

C1473SM-A 9/98 Original version.

7/00 Revised Figure 2 and Table B for new heater elements per ECO# 00-6032.

C1473SM-B 9/04 Revised parts list per ECO# 04-9848. Product redesigned to fit CC3610/CC3710/CC3770/MC3610/MC3710 Series cameras.

Pelco, the Pelco logo, Spectra, Genex, Esprit, Camclosure, and Legacy are registered trademarks of Pelco. All rights reserved.

© Copyright 2004, Pelco.

8 Pelco Manual C1473SM-B (9/04)