PRODUCT SPECIFICATION
video management solutions
Digital Sentry® DSSRV Network Video Recorder
H.264 CAPABILITY, FULLY SCALABLE HARDWARE/SOFTWARE SOLUTION
Product Features
• 280 Mbps to support IP and analog video
• Supports up to 128 IP Camera Streams; up to 64 Analog Cameras*
• Optimized to Support Pre-Installed DS NVs Software
• Records H.264, MJPEG, and MPEG-4 IP Streams
• Supports Pelco and Third-Party IP Cameras and Network Encoders
• Expandable by Networking an Unlimited Number of Servers and
Encoders (Dependent on Available Network Bandwidth)
• Compatible with DS ControlPoint for Simultaneous Monitoring of All
DS Series and DX Series Products in a Single Client Interface
• Network Health and Event Monitoring Support Through Simple
Network Management Protocol (SNMP) and New Digital Sentry
System Information (DSSI) Utility
®
• Compatible with the DS Archive Utility
• Recording Rate Configurable per Individual Camera
OPTIMIZED FOR VIDEO SURVEILLANCE
The Digital Sentry® Network Video Recorder (DSSRV NVR) is
optimized by Pelco to deliver the essential hardware support for the
DS NVs video management software (VMS) without the extra cost or
risk of integrating hardware and software.
®
Boosted by the 2nd Generation Intel
RAM, DSSRV NVR provides an optimal combination of processing
power and reliability to meet the demands of HD video recording and
playback operations. The system is powered to support up to 128
combined IP and analog video streams, with up to 64 analog cameras
supported via the optional ENC5416 direct-attached encoder. Analog
streams are also supported using Pelco and third-party encoders.
The DSSRV NVR delivers total available throughput of 280 Mbps for
recording of analog and IP video streams as well as playback and
export through the DS ControlPoint client. When determining the
maximum number of cameras and the desired frame rate to host on
each system, the number of concurrent client connections, the
number of streams likely to be viewed in playback on each client, and
the bandwidth required to support the client connections must be
taken into consideration.
The DSSRV NVR functions as a stand-alone system or as part of a
network of servers, monitored from the DS ControlPoint user
interface. The system can be deployed solely as a network video
recorder, as a digital video recorder (DVR), or as a hybrid NVR.
Core™ i7 processor and 8 GB of
Two gigabit network ports provide for convenient network
architecture planning by allowing one port to be dedicated to
IP cameras, while the second network port is used for client
connections. Two DVI-D ports provide a convenient connection for
high resolution digital monitors for use with HD cameras.
RELIABILITY
With front-available drives for easy servicing and upgrades, the
DSSRV NVR is available with up to 18 TB for models without the
optional optical disk drive (ODD), or up to 12 TB for ODD models. The
drives are hot-swappable when configured for internal RAID 5
storage with the optional RAID 5 controller card. A minimum of three
drives is required for a RAID 5 configuration. External storage is
supported through USB attached storage or by using the optional
DSSRV-SCSI interface card to connect to external SCSI storage
targets such as the DX8100HDDI, providing additional storage of up
to 24 TB. The external storage can be configured for JBOD storage of
software controlled RAID 5. Internal RAID 5 storage cannot be used
in conjunction with external storage.
Front panel LED displays on the DSSRV NVR provide information on
system operation. The LEDs are integrated with the new Digital
Sentry System Information (DSSI) utility, providing critical, real-time
statistics on system resource utilization, temperature, and
throughput status.
*The DS NVs database is limited to 128 cameras. The actual number of
cameras that can be supported is dependent on camera settings, client
connections and activity, network bandwidth, and the available
throughput of the DSSRV NVR.
International Standards
Organization Registered Firm;
ISO 9001 Quality System
C4693 / REVISED 3-25-13
TECHNICAL SPECIFICATIONS
DS CONTROLPOINT CLIENTS
SYSTEM
ADMINISTRATOR
SUPERVISORGUARDGUARD
DSSRV
ENC5416
ANALOG CAMERAS
IP CAMERAS
VIDEO ENCODER
ANALOG CAMERAS
TCP/IP
IP CAMERAS
IP CAMERAS
DX4700/DX4800
DX4700HD/DX4800HD
DSSRV
IMPORTANT NOTE. PLEASE READ. The network implementation is shown as a general representation only
and is not intended to show a detailed network topology. Your actual network will differ, requiring changes or
perhaps additional network equipment to accommodate the system as illustrated. Please contact your local
Pelco representative to discuss your specific requirements.
OPEN ARCHITECTURE
The cornerstone of Digital Sentry design, a fully Open Architecture, is
provided through ONVIF compliance and support for a large number
of IP-specific drivers. Users can choose specific IP cameras or
encoders to fit their application.
In addition, the Digital Sentry platform supports the Pelco API and a
full suite of integration tools, allowing Digital Sentry to be integrated
into access control or PSIM systems
Eliminate the risk of deferred support that comes with VMS software
from one vendor and a general purpose hardware platform from
another. Replace it with the assurance of an integrated platform built
specifically for the rigors of IP video recording. Make the
performance, reliability, and Open Architecture of DS NVs running on
DSSRV NVR the core foundation of your video management solution.
TECHNICAL SPECIFICATIONS
SYSTEM
Processor 2nd Generation Intel® Core™ i7
Operating System Windows 7 Ultimate 64-bit SP1
Internal Memory 8 GB RAM
User Interface DS ControlPoint
Internal Storage (JBOD or RAID 5*)
DSSRV 500 GB, 3 TB, 6 TB, 9 TB, 12 TB, 15 TB, or
18 TB
DSSRV-DVD 500 GB, 3 TB, 6 TB, 9 TB, or 12 TB
RAID Level Internal RAID 5 (requires DSSRV-RAID
controller card for hot-swappable drives)
†
External Storage Pelco’s DX8100HDDI or third-party SCSI
targets (requires optional DSSRV-SCSI)
System Drives
DSSRV
‡
6, 3.5-inch hard drive bays
DSSRV-DVD 4, 3.5-inch hard drive bays
Optical Drive DVD±RW with DSSRV-DVD
*The minimum configuration for an internal RAID 5 is three hard disk
drives. One hard disk drive of the RAID 5 configuration is used for parity,
reducing net storage capacity by the storage capacity of one hard disk
drive. For example, an 18 TB RAID system provides net storage of 15 TB.
†
Requires an optional DSSRV-RAID controller card. The internal RAID 5
requires reimaging of the system.
‡
DVD and non-DVD models are each different form factors. DVD models
have only four drive bays; non-DVD models have six drive bays.
REMOTE CLIENT PC REQUIREMENTS
Operating System Microsoft® Windows® XP Professional SP2,
Windows Vista
§
®
(32 or 64 bit),
Windows 7 (32 or 64 bit)
®
Processor 2nd Generation Intel
Core™ i7 3.4 GHz or
higher
Memory 4 GB DDR3 or higher
Graphics Card 512MB or more dedicated memory
§
While the DS ControlPoint client can be run at the server, doing so can
impact performance of the DSSRV. For optimum performance, run
DS ControlPoint at a client station.
NETWORK
Interface 2 Gigabit Ethernet RJ-45 (1000Base-T,
Auxiliary Interfaces
USB Ports 1 front (USB 2.0)
non load balancing)
4 rear (2 USB 3.0; 2 USB 2.0)
POWER
Power Input 100 to 240 VAC, 50/60 Hz, autoranging
Power Supply Internal
Power Consumption Operating Maximum
100 VAC / 50 Hz 222.0 2.22 758.0
110 VAC / 50 Hz 224.0 2.02 759.4
110 VAC / 60 Hz 223.0 2.03 761.4
115 VAC / 50 Hz 217.0 1.89 740.8
115 VAC / 60 Hz 215.5 1.87 735.7
220 VAC / 50 Hz 213.0 0.97 727.2
220 VAC / 60 Hz 204.1 0.93 696.8
240 VAC / 50 Hz 211.9 0.88 723.4
240 VAC / 60 Hz 207.6 0.86 708.8
Watts Amperes BTU/H
CONNECTIONS
Video Out 2 DVI-D connectors, 1 VGA connector. A
maximum of 2 video out connectors can be
used.**
Audio Out 1, 1/8-inch audio jack connector
**Running the client software on the DSSRV NVR server degrades the
performance of the server; therefore, running the DS ControlPoint remote
client at one or more stations is recommended.
FRONT PANEL INDICATORS/FUNCTIONS
Buttons Power
Indicators
Unit Status Green, amber, red
Primary Network Green, amber, red
Secondary Network Green, amber, red
Software Status Green, amber, red (based on diagnostics)
Hard Disk Status Green, red, off (behind bezel)
ENVIRONMENTAL
Operating Temperature 10° to 35°C (50° to 95°F)
Storage Temperature –40° to 65°C(–40° to 149°F)
Operating Humidity 20% to 80%, noncondensing
Maximum Humidity Gradient 10% per hour
Operating Altitude –15 to 3,048 m (–50 to 10,000 ft)
Operating Vibration 0.25 G at 3 Hz to 200 Hz at a rate of
0.5 octave/minute
Note: The temperature at the unit air intake can be significantly higher than
room temperature. Temperature is affected by rack configuration, floor
layout, air conditioning strategy, and other issues. To prevent performance
failure and unit damage, make sure the temperature at the unit is
continuously within the operating temperature range.
PHYSICAL
Dimensions 50.8 x 43.4 x 8.9 cm
(20" D x 17.1" W x 3.5" H)
Weight Unit Shipping
DSSRV-005 11.8 kg (26 lb) 20.9 kg (46 lb)
DSSRV-030 11.8 kg (26 lb) 20.9 kg (46 lb)
DSSRV-060 12.7 kg (28 lb) 21.8 kg (48 lb)
DSSRV-090 13.6 kg (30 lb) 22.7 kg (50 lb)
DSSRV-120 14.5 kg (32 lb) 23.6 kg (52 lb)
DSSRV-150 15.4 kg (34 lb) 24.5 kg (54 lb)
DSSRV-180 16.3 kg (36 lb) 25.4 kg (56 lb)
DSSRV-005DVD 12.7 kg (28 lb) 21.8 kg (48 lb)
DSSRV-030DVD 13.6 kg (30 lb) 22.7 kg (50 lb)
DSSRV-060DVD 14.5 kg (32 lb) 23.6 kg (52 lb)
DSSRV-090DVD 15.4 kg (34 lb) 24.5 kg (54 lb)
DSSRV-120DVD 16.3 kg (36 lb) 25.4 kg (56 lb)
DSSRV-RD-090 13.6 kg (30 lb) 23.6 kg (52 lb)
DSSRV-RD-012 14.5 kg (32 lb) 24.3 kg (54 lb)
DSSRV-RD-015 15.4 kg (34 lb) 25.2 kg (56 lb)
DSSRV-RD-018 16.3 kg (36 lb) 26.1 kg (58 lb)
TECHNICAL SPECIFICATIONS
Pelco, the Pelco logo, and other tra demarks associated with Pelco products referred
to in this publication are trademarks of Pelco, Inc. or its affiliates. ONVIF and the
ONVIF logo are trademarks of ONVIF Inc. All oth er product names and
services are the property of their respect ive companies.
Product specifications and availability are subject to change without notice.
©Copyright 2013, Pelco, Inc. All rights reserved.
Notice: Judgment as to the suitability of the products for users’ purposes is solely the
users’ responsibility. Users should refer to the Operation manuals for cautionary
statements regarding user selected options and how they might affect video quality.
Users shall determine the suitability of the products for their own intended application,
picture rate and picture quality. In the event users intend to use the video for evidentiary
purposes in a judicial proceeding or otherwise, users should consult with their attorney
regarding any particular requirements for such use.
MODELS
The following table describes the DSSRV and DSSRV-DVD model numbers.
For example, the model number for a 12 TB, DSSRV device with a
United Kingdom power cord is DSSRV-120-UK. The model number for a 6 TB,
DSSRV-DVD device with an Australian power cord is DSSRV-060DVD-AU.
Note: Units shipped to China do not include power cords.
Model Storage Country Code
NVR Without Optical Disk Drive
DSSRV-005 500 GB
DSSRV-030 3 TB
DSSRV-060 6 TB
DSSRV-090 9 TB
DSSRV-120 12 TB
DSSRV-150 15 TB
DSSRV-180 18 TB
NVR With RAID Configuration
DSSRV-RD-090 9 TB
DSSRV-RD-012 12 TB
DSSRV-RD-015 15TB
US = North America
EU = Europe
UK = United Kingdom
CN = China
AU = Australia
AR = Argentina
DSSRV-RD-018 18TB
NVR With Optical Disk Drive
DSSRV-005DVD 500 GB
DSSRV-030DVD 3 TB
DSSRV-060DVD 6 TB
DSSRV-090DVD 9 TB
DSSRV-120DVD 12 TB
SUPPLIED ACCESSORIES
Power Cord 1 USA standard, 1 based on country
USB Keyboard and Mouse 1
Bezel key 2
Rack Mount Kit Brackets, rails, and hardware for mounting in
DSSRV-LIT Documentation, resource and recovery discs
USB-DS For non-DVD models; the USB stick is imaged
designation; all cables are 3 prong, molded
connector, 1.8 m (6 ft)
Note: Units shipped to China do not include
power cords.
a 2 RU rack
with DS NVs and includes resource
documentation
OPTIONAL ACCESSORIES
DS-SW-CAM DSSRV models include eight licenses for
ENC5416 Direct-attached analog encoder
ENC5400-4PORT 4-port host card (analog)
DSSRV-RAID LSI 3Ware 9750-8i RAID controller card
DSSRV-SCSI Adaptec
DSHDD-005 500 GB upgrade/replacement drive
DSHDD-030 3 TB upgrade/replacement drive
Note: Only joystick control is supported. Mouse operation is required to move
between tear-off tabs in DS ControlPoint. Endura color-coded keys are not
supported.
Pelco and third-party IP cameras. Additional
DS-SW-CAM licenses can be purchased
separately.
connects 4 ENC5416
®
SCSI Card 29320LPE
CERTIFICATIONS/RATINGS
• CE, Class A; meets EN50130-4 standard requirements
• FCC, Class A
• UL/cUL Listed
•C-Tick
•CCC
•KCC
•S-Mark
STANDARDS/ORGANIZATIONS
• Pelco is a member of the MPEG-4 Industry Forum
• Pelco is a member of the Universal Plug and Play (UPnP) Forum, Steering
Committee
• Pelco is a member of the Universal Serial Bus (USB) Implementers Forum
• Pelco is a contributor to the Internal Standards for Organization/
Electrotechnical Commission (ISO/IEC) Joint Technical Committee 1
(JTC1), “Information Technology,” Subcommittee 29, Working Group 11
• Compliance, ISO/IEC 14496 standard (also known as MPEG-4)
• Compliance, International Telecommunication Union (ITU)
Recommendation G.711, “Pulse Code Modulation (PCM) of Voice
Frequencies”
• Pelco is a member of the ONVIF Open Industry Forum
Pelco by Schneider Electric
3500 Pelco Way, Clovis, California 93612-5699 United States
USA & Canada Tel (800) 289-9100 Fax (800) 289-9150
International Tel +1 (559) 292-1981 Fax +1 (559) 348-1120
www.pelco.com www.pelco.com/community
Loading...