Pelco DSSRV2-005-D, DSSRV2-005DV-US, DSSRV2-040-D, DSSRV2-040, DSSRV2-040DV-D Specsheet

...
PRODUCT SPECIFICATION
video management solutions
Digital Sentry® DSSRV2 Network Video Recorder
H.264 CAPABILITY, FULLY SCALABLE HARDWARE/SOFTWARE SOLUTION
Product Features
Increased data rate of up to 350 Mbps (RAID) or 300 Mbps (JBOD)
total throughput, allowing the server to support more users and play back more cameras simultaneously than previous DSSRV models
4TB storage drives provide 33% more storage over DSSRV 3TB
models at no additional cost; systems previously utilizing two or more servers can now be built on a single server
SSD system drive, with increased read-write speeds and no moving
parts, increases overall system responsiveness and reliability
Supports up to 128 IP Camera Streams; up to 64 Analog Cameras*
Records H.264, MJPEG, and MPEG-4 IP Streams
Supports Pelco and Third-Party IP Cameras and Network Encoders
Compatible with DS ControlPoint for Simultaneous Monitoring of All
DS Series and DX Series Products in a Single Client Interface
Network Health and Event Monitoring Support Through SNMP and
New Digital Sentry
®
System Information (DSSI) Utility
Compatible with the DS Archive Utility
Recording Rate Configurable per Individual Camera
VideoXpert Ready. Migrate to VideoXpert, bringing your products
forward into a next generation VMS
Optimized For Video Surveillance
The Digital Sentry® Network Video Recorder (DSSRV2 NVR) is optimized by Pelco to deliver the essential hardware support for the DS NVs video management software (VMS) without the extra cost or risk of integrating hardware and software.
Boosted by the 4th Generation Intel® Xeon™ processor and 8 GB of RAM, DSSRV2 NVR provides an optimal combination of processing power and reliability to meet the demands of HD video recording and playback operations. The system is powered to support up to 128 combined IP and analog video streams, with up to 64 analog cameras supported via the optional ENC5516 direct-attached encoder. Analog streams are also supported using Pelco and third-party encoders.
The DSSRV2 NVR boasts total throughput of up to 350 Mbps (300 Mbps for JBOD models) for recording analog and IP video streams as well as playback and export through the DS ControlPoint client. The increased data rate over original DSSRV models allows more users to play back video from the server simultaneously. When determining the maximum number of cameras and the desired frame rate to host on each system, the number of concurrent client connections, the number of streams played back per client, and the bandwidth required for client connections must be considered.
The DSSRV2 NVR functions as a stand-alone system or as part of a network of servers, monitored from the DS ControlPoint user interface. The system can be deployed solely as a network video recorder, as a digital video recorder (DVR), or as a hybrid NVR.
Two gigabit network ports provide for convenient network architecture planning by allowing one port to be dedicated to IP cameras, while the second network port is used for client connections. Two DisplayPorts ports provide a convenient connection for high resolution digital monitors for use with HD cameras.
DSSRV2 models are available with DIACAP/DIARMF-ready software, for use in secured environments implementing information assurance security standards.
Reliability
DSSRV2 models incorporate an SSD system drive. With increased read-write speeds and no moving parts, the SSD system drive increases the reliability, uptime, and responsiveness of the system. DSSRV2 systems now support 4TB drives, increasing capacity by 33% over original DSSRV models without increasing cost. With front­available storage drives for easy servicing and upgrades, the DSSRV2 NVR is available with up to 20 TB storage for models without the optional optical disk drive (ODD), or up to 16 TB for ODD models. The drives are hot-swappable when configured for internal RAID 5 storage.
External storage is supported through USB attached storage or by using the optional DSSRV-SCSI interface card to connect to external SCSI storage targets such as the DX8100HDDI, providing additional storage of up to 24 TB. The external storage can be configured for either JBOD storage or for software controlled RAID 5 storage.
*The DS NVs database is limited to 128 cameras. The actual number of
cameras the server supports depends on camera settings, client activity, network bandwidth, and the available throughput of the DSSRV2.
International Standards
Organization Registered Firm;
ISO 9001 Quality System
C4014 / REVISED 2-25-16
TECHNICAL SPECIFICATIONS
DS CONTROLPOINT CLIENTS
SYSTEM
ADMINISTRATOR
SUPERVISORGUARDGUARD
DSSRV2
ENC5516
ANALOG CAMERAS
IP CAMERAS
VIDEO ENCODER
ANALOG CAMERAS
TCP/IP
IP CAMERAS
DX8100
IP CAMERAS
DX4700/DX4800
DSSRV2
IMPORTANT NOTE. PLEASE READ. The network implementation is shown as a general representation only and is not intended to show a detailed network topology. Your actual network will differ, requiring changes or perhaps additional network equipment to accommodate the system as illustrated. Please contact your local Pelco representative to discuss your specific requirements.
Open Architecture
The cornerstone of Digital Sentry design, a fully Open Architecture, is provided through ONVIF compliance and support for a large number of IP-specific drivers. Users can choose specific IP cameras or encoders to fit their application.
In addition, the Digital Sentry platform supports the Pelco API and a full suite of integration tools, allowing Digital Sentry to be integrated into access control or physical security information management (PSIM) systems.
Eliminate the risk of deferred support that comes with VMS software from one vendor and a general purpose hardware platform from another. Replace it with the assurance of an integrated platform built specifically for the rigors of IP video recording. Make the performance, reliability, and Open Architecture of DS NVs running on DSSRV2 NVR the core foundation of your video management solution.
TECHNICAL SPECIFICATIONS
SYSTEM
Processor Intel® Xeon E3-1275 v3 Operating System Windows 7 Ultimate 64-bit Internal Memory 8 GB DDR3 non-ECC RAM; 16 GB DDR ECC
User Interface DS ControlPoint Internal Storage (JBOD or RAID 5*)
DSSRV2 500 GB, 4 TB, 8 TB, 12 TB, 16 TB, 20 TB DSSRV2-DVD 500 GB, 4 TB, 8 TB, 12 TB, or 16 TB DSSRV2-RD 12 TB, 16 TB, 20 TB, or 24 TB
RAID Level Internal RAID 5 (requires DSSRV-RAID
External Storage Pelco’s DX8100HDDI or third-party SCSI
System Drive SSD Storage Drives
DSSRV2 6, 3.5-inch hard drive bays
DSSRV2-DVD 4, 3.5-inch hard drive bays Optical Drive DVD±RW with DSSRV2-DVD USB Ports 3 USB 2.0 ports (1 front, 2 rear)
*The minimum configuration for an internal RAID 5 is three hard disk drives.
One hard disk drive of the RAID 5 configuration is used for parity, reducing net storage capacity by the storage capacity of one hard disk drive. For example, an 18 TB RAID system provides net storage of 15 TB.
RAM for DSSRV2-RD models
controller card for hot-swappable drives)
targets (requires optional DSSRV-SCSI)
2 USB 3.0 ports (rear)
VIDEO
Video System Intel HD Graphics P4700 (shared memory)
Maximum Resolution 3840 x 2160 per DisplayPort output (2x)
Video Outputs Supports up to 3 simultaneous displays using
Video Standards 60 Hz capable for NTSC
Video Decoding Supported MPEG-4 ASP; H.264 Baseline, Main, and
Panoramic Motion Recording Supports up to 8 Oncam EV0-05, or
Panoramic Continuous Recording
Running client software on the server limits the server’s performance. It is
recommended that you run DS ControlPoint on a separate client to ensure optimal server and recording performance.
1920 x 1200 @ 60 hz on DVI-D output 1920 x 1200 @ 60 hz on VGA output
any combination of the four outputs
75 Hz capable for PAL
High profiles
EVO-12 cameras
Supports up to 8 Oncam EV0-05, or EVO-12 cameras
Supports up to 6 Optera IMM Series cameras
AUDIO
Audio Decoding G.711 speech codec Audio Bit-rate 64 kbps Audio Levels
Input Electret microphone
Output Up to 3 Vp-p, adjustable, minimum load of
Audio Connectors 2, 3.5 mm stereo jacks
Connector Tip Signal left (input and output)
Connector Ring Signal right (input and output)
Connector Sleeve Common Audio Inputs Microphone Audio Outputs Speaker or line out
8 ohms
NETWORK
Interface Gigabit Ethernet (1000Base-T) ports (2x)
POWER
Power Input 100 to 240 VAC, 50/60 Hz, autoranging Power Supply Internal Power Consumption Operating Maximum
Watts Amperes BTU/H 100 VAC / 50 Hz 222.0 2.22 758.0 110 VAC / 50 Hz 224.0 2.02 759.4 110 VAC / 60 Hz 223.0 2.03 761.4 115 VAC / 50 Hz 217.0 1.89 740.8 115 VAC / 60 Hz 215.5 1.87 735.7 220 VAC / 50 Hz 213.0 0.97 727.2 220 VAC / 60 Hz 204.1 0.93 696.8 240 VAC / 50 Hz 211.9 0.88 723.4 240 VAC / 60 Hz 207.6 0.86 708.8
FRONT PANEL INDICATORS/FUNCTIONS
Buttons Power Indicators
Unit Status Green, amber, red Primary Network Green, amber, red Secondary Network Green, amber, red Software Status Green, amber, red (based on diagnostics) Hard Disk Status Green, red, off (behind bezel)
ENVIRONMENTAL
Operating Temperature 10° to 35°C (50° to 95°F) Storage Temperature –40° to 65°C (–40° to 149°F) Operating Humidity 20% to 80%, noncondensing Maximum Humidity Gradient 10% per hour Operating Altitude –15 to 3,048 m (–50 to 10,000 ft) Operating Vibration 0.25 G at 3 Hz to 200 Hz at a rate of
0.5 octave/minute
Note: The temperature at the unit air intake can be significantly higher than room temperature. Temperature is affected by rack configuration, floor layout, air conditioning strategy, and other issues. To prevent performance failure and unit damage, make sure the temperature at the unit is continuously within the operating temperature range.
PHYSICAL
Dimensions 50.8 x 43.4 x 8.9 cm
(20" D x 17.1" W x 3.5" H)
Weight Unit Shipping
DSSRV2-005 11.8 kg (26 lb) 20.9 kg (46 lb) DSSRV2-040 11.8 kg (26 lb) 20.9 kg (46 lb) DSSRV2-080 12.7 kg (28 lb) 21.8 kg (48 lb) DSSRV2-120 14.5 kg (32 lb) 23.6 kg (52 lb) DSSRV2-160 15.4 kg (34 lb) 24.5 kg (54 lb) DSSRV2-200 16.3 kg (36 lb) 25.4 kg (56 lb) DSSRV2-005DVD 12.7 kg (28 lb) 21.8 kg (48 lb) DSSRV2-040DVD 13.6 kg (30 lb) 22.7 kg (50 lb) DSSRV2-080DVD 14.5 kg (32 lb) 23.6 kg (52 lb) DSSRV2-120DVD 15.4 kg (34 lb) 24.5 kg (54 lb) DSSRV2-160DVD 16.3 kg (36 lb) 25.4 kg (56 lb) DSSRV2-120RD 13.6 kg (30 lb) 23.6 kg (52 lb) DSSRV2-160RD 14.5 kg (32 lb) 24.3 kg (54 lb) DSSRV2-200RD 15.4 kg (34 lb) 25.2 kg (56 lb) DSSRV2-240RD 16.3 kg (36 lb) 26.1 kg (58 lb)
TECHNICAL SPECIFICATIONS
Pelco, the Pelco logo, and other tra demarks associated with Pelco products referred
to in this publication are trademarks of Pelco, Inc. or its affiliates. ONVIF and the
ONVIF logo are trademarks of ONVIF Inc. All oth er product names and
services are the property of their respect ive companies.
Product specifications and availability are subject to change without notice.
©Copyright 2015, Pelco, Inc. All rights reserved.
Notice: Judgment as to the suitability of the products for users’ purposes is solely the users’ responsibility. Users should refer to the Operation manuals for cautionary statements regarding user selected options and how they might affect video quality. Users shall determine the suitability of the products for their own intended application, picture rate and picture quality. In the event users intend to use the video for evidentiary purposes in a judicial proceeding or otherwise, users should consult with their attorney regarding any particular requirements for such use.
MODELS
The following table describes model numbers for DSSRV2 products. For example, the model number for a 12 TB, DSSRV2 device with a United Kingdom power cord is DSSRV2-120-EUK. The model number for a 8 TB, DSSRV2-DVD device with an North American power cord is DSSRV2­080DV-US. Models ending in D are for use in DIACAP/DIARMF security­enabled environments.
Model Storage Country Code (optional)
NVR Without Optical Disk Drive
DSSRV2-005 500 GB
DSSRV2-040 4 TB
DSSRV2-080 8 TB
DSSRV2-120 12 TB
DSSRV2-160 16 TB
DSSRV2-200 20 TB
NVR With RAID Configuration
DSSRV2-120RD 12 TB
DSSRV2-160RD 16 TB
US = North America EUK = Europe/United Kingdom D = DIACAP/DIARMF
DSSRV2-200RD 20 TB
DSSRV2-240RD 24 TB
NVR With Optical Disk Drive
DSSRV2-005DV 500 GB
DSSRV2-040DV 4 TB
DSSRV2-080DV 8 TB
DSSRV2-120DV 12 TB
DSSRV2-160DV 16 TB
SUPPLIED ACCESSORIES
Power cord (for applicable models) USB Keyboard and Mouse 1 Bezel Key 2 Rack Mount Kit Brackets, rails, and hardware for mounting in
DSSRV-LIT Documentation USB-DS Imaged with DS NVs and includes resource
a 2 RU rack
documentation
OPTIONAL ACCESSORIES
DS-SW-CAM DSSRV2 models include eight licenses for
ENC5516 Direct-attached analog encoder ENC5400-4PORT 4-port host card; connects 4 ENC5416 or
DSSRV2-RAID LSI 3Ware 9750-8i RAID controller card DSSRV2-SCSI Adaptec DSHDD-005 500 GB upgrade/replacement drive DS-EN-HDD-4TB 4 TB upgrade/replacement drive PWRCRD-S-AR Standard power cord, Argentina PWRCRD-S-AU Standard power cord, Australia PWRCRD-S-EU Standard power cord, Europe PWRCRD-S-UK Standard power cord, United Kingdom PWRCRD-S-US Standard power cord, United States Note: Only joystick control is supported. Mouse operation is required to move
between tear-off tabs in DS ControlPoint. Endura color-coded keys are not supported.
Pelco and third-party IP cameras; additional DS-SW-CAM licenses can be purchased separately
ENC5516 encoders
®
SCSI Card 29320LPE
CERTIFICATIONS/RATINGS
• CE, Class A; meets EN50130-4 standard requirements
• FCC, Class A
• UL/cUL Listed
•C-Tick
•CCC
•KCC
STANDARDS/ORGANIZATIONS
• Pelco is a member of the MPEG-4 Industry Forum
• Pelco is a member of the Universal Plug and Play (UPnP) Forum, Steering Committee
• Pelco is a member of the Universal Serial Bus (USB) Implementers Forum
• Pelco is a contributor to the Internal Standards for Organization/ Electrotechnical Commission (ISO/IEC) Joint Technical Committee 1 (JTC1), “Information Technology,” Subcommittee 29, Working Group 11
• Compliance, ISO/IEC 14496 standard (also known as MPEG-4)
• Compliance, International Telecommunication Union (ITU) Recommendation G.711, “Pulse Code Modulation (PCM) of Voice Frequencies”
• Pelco is a member of the ONVIF Open Industry Forum
Pelco by Schneider Electric
3500 Pelco Way, Clovis, California 93612-5699 United States
USA & Canada Tel (800) 289-9100 Fax (800) 289-9150 International Tel +1 (559) 292-1981 Fax +1 (559) 348-1120 www.pelco.com www.pelco.com/community
Loading...