Pelco C1501M, C578M, C573M-D, C541M-C, C542M-B User Manual

ADDENDUM

Addendum No.: C1577M-A

Date: August 4, 2004

Manuals Affected: CM9760 Series Manuals – C538M, C539M-A, C540M-B, C541M-C, C542M-B, C543M-A,

C544M, C549M-A, C572M, C573M-D, C578M, C579M, C1501M, C1503M, C1510M-QS,
C1510M-A, C1520M-B, C1528M-C, C1940M, C1941M, C1942M, and C1943M

Manual Update: The CM9760-CC1 has been replaced with the CM9700-CC1 and the CM9760-MGR manage-

ment software has been replaced with the CM9700-MGR management software.

Keep the following in mind when referring to the instructions contained in these manuals:

• The CM9700-CC1 contains the latest CC1 software (version 9.01 or higher), and is
programmed with the new CM9700-MGR management software.

• Despite the difference in model numbers, the CM9700-CC1 functions the same as the
CM9760-CC1 and most of the information in these manuals applies to version 9.01 (or
higher) CPU.

•You can add the CM9700-CC1 to an existing CM9760 system if you upgrade the existing
CM9760-CC1 units with the current software (version level 9.01 or higher).

Software version 9.01 requires a minimum of 16 MB of RAM in the CPU. If required, you
can upgrade the RAM in older CM9760-CC1 units using the software upgrade kit
appropriate for your CPU.

• Do not use the CM9760-MGR instructions contained in these manuals. Refer to the
CM9700-MGR Getting Started Software Guide, on-screen help, or Online Help for
instructions.

Pelco World Headquarters • 3500 Pelco Way, Clovis, California 93612-5699 USA • www.pelco.com

USA & Canada: Tel: [phone] • Fax: [phone]

®

International: Tel: [phone] • Fax: [phone]

CM9760-SAT

Satellite Switcher/

Controller

Installation/

Operation Manual

C1510M-A (2/03)

Pelco World Headquarters • 3500 Pelco Way, Clovis, CA 93612-5699 USA • www.pelco.com

USA & Canada: Tel: [phone] • Fax: [phone]

International: Tel: [phone] • Fax: [phone]

CC1 Interface:

(Comm Parameters)

Equipment # 31
Baud Rate 9600
Parity ODD

F R O N T

Required Software:

CM9760-MGR (System MGR) @ ver 7.80.003 or greater (external PC)
CM9760.EXE @ ver 7.80.003 or greater (9760 HD)
CM9760-KBD @ ver 7.80 or greater

(For software upgrade information, contact Technical Support at 1-800-289-9100.)

The CM9760-SAT is a sequential video switcher
for use as a Satellite Control System of the
CM9760 system. Below are shown the front and
rear views, the mounting geometry and, for ref­erence, the pinout designations for all connec­tors on the unit. The four, 12-pin and one, 6-pin
wiring plugs (shown in Figure 2) are supplied
with the unit. Especially note the COM 2 con­nector designations. Required software version
levels and other Comm parameters are given
in the information box to the left.

• Observe the precaution outlined
in the NOTE below.

• Orient unit as required.

• Mount as deemed appropriate
to your installation.

NOTE:

Factory default, video input termina­tion is 75-ohm, non-looping. If you want the
loop-thru option active for any video input, the
top cover of the unit must be removed to make
the change
Video Inputs

(see Section 1,

).

You may want to do this before

3.2.1, Looping

rack-mounting the unit.

FIGURE 1

CM9760-SAT Front View, Including Mounting Geometry

R E A R

FIGURE 2

CM9760-SAT Rear View

INTRODUCTION CM9760-SAT i

MANUAL NOTES

1. The approach used in this manual is predicated on the installation
and operation of the CM9760-SA T in a 9760 System environment.
Figure 3 is a block diagram that represents such an environment.

2. Figure 3 is our reference or “jumping-off” point for most discussions
in this manual. Note that the block diagram is divided in half: one
side is labeled the “9760 SIDE” and the other is labeled the “SAT
SIDE”. For each, we discuss installation, programming, configura­tion, and operation, in the order listed in the MANUAL DIREC-
TORY on the next page.

3. The KBD200, KBD300, and KBD300V are keypads that connect to
the SAT SIDE in our sample system environment where they are
used for local operation and programming of the CM9760-SAT.
A section on keypad operations, separate from their actual use in
a programming or operational situation, is not included in the main
body of the manual. This is done to minimize the interruption that
would be involved in flipping back and forth between a section on
the mechanics of keypad operation and the discussion at hand.
Every effort is made to include all data needed to carry out a pro­posed operation or programming function at the point where it is
discussed or used in the manual. However, we do provide, in Ap­pendix III,
KBD200/KBD300/KBD300V keypad layout and button description.

Keypad Definitions and Templates,

FIGURE 3

9760-SAT System Environment

an abbreviated

4. Extensive discussions of keyboard and keypad connections (other
than local SAT keypad hookup) are not included in the main body
of the manual. For example, although multiple keypads can be con­nected to the SAT, you will not find a two-page digression in the
middle of the manual on how to do it. Multiple keypad hookup is
covered in Appendix II,
attempt to minimize blanket statements like “connect a straight-wired
cable at one point”, or “connect a reverse-wired cable at another”,
and, instead, encourage you to determine the parameters of cable
hookup to your own satisfaction. Overt statements like those just
mentioned are based on assumptions that may not be true for your
on-site situation. When installing a supplied cable yourself, you
should not blindly attach the cable (supplied or on-site) without know­ing that the connection you make should work. In fact, you should
be surprised if it does not work. Specific instructions and sugges­tions on matters related to keypad hookup and communication wir­ing are found in Appendix I,

Tutorial

and Appendix II,
just a few pertinent facts at your disposal in order to connect 9760
communication devices together correctly.

Remote Keypad Connections

. Similarly, we

Communication and Connection

Remote Keypad Connections

. Y ou need

ii C1510M-A (2/03) INTRODUCTION

MANUAL DIRECTORY

INTRODUCTION iv

SECTION 1 1-1 Physical Installation

This section describes the physical installation of communication and video lines necessary for SAT
system operation. Instructions for connecting additional equipment, necessary for proper operation at
the local SAT SIDE, are also discussed. The choices made here are reflected in the configuration of
the applicable programming menus (SAT SIDE) and flat files (9760 SIDE), which are covered in
Section 2.

SECTION 2 2-4 Programming and Configuration

SAT programming menus are discussed first.

NOTE:

These menus are normally programmed via a local keypad connection on the
system. They can also be programmed from the
accomplish these tasks are possible. Whether you program from the local

9760 SIDE

tem

, depends upon choices made about your particular equipment configuration. How

these setups affect your choice of programming vehicle is discussed in Section 2, PRELIMINARIES.

Next, other programming functions related to local SAT operation are discussed (presets, patterns,
zones and so on).

This section concludes with a discussion on how to program the 9760-MGR (System Manager) configu­ration or “flat” files for proper operation of the 9760-SAT link.

SECTION 3 3-1 Operation

SAT operation on the local SAT SIDE of the system is discussed first. These include keyboard acti-

vated functions for camera/monitor selections and control operations for other functions including se­quence, pattern, and zone operations, as well as the control of auxiliaries.

Locally activated alarms on the SAT SIDE lead to discussions of 9760 System-SAT alarm responses.
Alarm response, in turn, leads to a discussion on how different equipment configurations are integrated
into the 9760 system as a whole. You may have only one SAT, or perhaps two SATs, or one SAT and
a 9760-ALM unit, or two SAT units and an ALM unit.

Alarm responses for the 9760-ALM unit are structured differently from that of the SAT unit, yet both use
the same Alarms system configuration file. How it actually works is discussed here.

9760 SIDE

SAT SIDE

of the

via a 9760-KBD. A number of ways to

SAT SIDE

or from the sys-

SECTION 4 4-1 System and Multiplexer Example

A basic 9760-SAT system example that demonstrates the basics of system hookup and programming is
considered. The example is dissected in a step-by-step, detailed manner. At each step, the hookup and
programming functions affecting that portion of the system are discussed. References to applicable
manual sections are given where appropriate. The basics of integrating a Genex multiplexer into a 9760­SAT system environment is also discussed.

4-11 Multiplexer Example

SECTION 5 5-1 Appendices

A short tutorial on device interconnections is given. Keypad definitions, templates and remote keypad
connections are followed by a listing of SAT models and associated equipment. We round out the
section with a menu-listing of SAT Programming Default Reset parameters and a connector pinout list
for all devices used in the manual.

SECTION 6 6-1 Miscellaneous

6-1 Safeguards and Warnings
6-2 Specifications
6-3 Index
6-5 Regulatory Notices
6-5 Warranty

INTRODUCTION CM9760-SAT iii

INTRODUCTION

Physical

Description

The SAT-9760

Relationship

Setup

Overview

The CM9760-SAT is a 16 X 4 (16 camera input by 4 monitor output) cross-point video matrix, sequential
switcher.

The physical appearance of the 16 X 4 SAT is dominated by the 16 video inputs (and corresponding
loop-thru BNCs) on the rear of the unit. Four BNC monitor-outs (for local or tie line use), four 12-pin
wiring plugs for other functions and, finally, local and remote keypad ports round out the device connec­tion list. Aside from confirming whether or not loop-thru operation is part of your configuration, the unit
is ready to be rack-mounted. Remember: there is no “ON/OFF” switch and therefore the unit should not
be plugged in until all connections to it have been made.

Although the SAT is a peripheral device of the 9760 system, it is unique in that a considerable amount
of local programming and control freedom can exist at the downstream or SAT SIDE of the configura-
tion. Y ou can think of the SAT as capable of performing many of the functions normally associated with
a single node of the 9760 system. This analogy extends to include programmed SAT alarm-event
notifications to the 9760 system. In some configurations, you might want to ignore local SAT functions
altogether and use all monitor-out lines as tie lines back to the main system.

To enable operation of these functions, the following tasks must be performed:

1. Physically, the SAT and the 9760 system communicate in full duplex mode via an RS-422 Com
link between the CM9760-CC1 and the port provided on the SAT. Those SAT monitor-out lines
(configured as tie lines), must be run back to the 9760 SIDE and connected as video inputs to the
matrix bay and those monitor-outs not configured as tie lines must be configured for LOCAL use.

2. In addition to physical hookup, configuration files must be programmed on the 9760 SIDE to
make the 9760 aware of the SAT’s existence and to condition tie line connect points. The informa-
tion box found at the beginning of this manual lists the minimum version levels of software needed
by equipment on both sides of the configuration to operate the 9760-SAT system interface.

3. By far, the majority of programming occurs on the SAT SIDE and serves a dual purpose. The first
is to condition the SAT-9760 interface, in particular, the tie line link(s) between the 9760-MXB
and the associated monitor outputs on the SAT. This is accomplished through programming the
applicable entries in the SAT’s Monitor menu. Other menus (for example, those that set up
communication port attributes) are affected as well. The second purpose involves programming
all associated link cameras, monitors, alarms and other connections for PTZ functions and other
SAT sequential switcher operations for use at the local level. Local programming and operation
of the SAT and associated link cameras are controlled by desktop keypads (the KBD200, KBD300
or KBD300V).

iv C1510M-A (2/03) INTRODUCTION

SECTION 1 PHYSICAL INSTALLATION

1.0 COM CONNECTION ....................................................... 1-1

9760 SIDE

CC1 to Wall Block ............................................................. 1-2

SAT SIDE

Wall Block to SAT ............................................................. 1-2

2.0 VIDEO TIE-LINES ........................................................... 1-2

9760 SIDE ........................................................................... 1-2

SAT SIDE ............................................................................. 1-2

3.0 ADDITIONAL SAT CONNECTIONS ............................ 1-3

Local Monitor ................................................................. 1-3

Link Cameras....................................................................... 1-3

Looping Video Inputs ..................................................... 1-3

Receivers ....................................................................... 1-4

Alarms............................................................................ 1-4

Auxs ............................................................................... 1-5

Local Keypads ............................................................... 1-5

1.0 COM CONNECTION

The COM connection between the CM9760-CC1 and the CM9760-SAT runs from an available sercom port** on the rear of the CC1 to appropriate
pinouts located on the wiring plug for COM 2 on the SAT. A physical disparity exists between the RJ-45 connector on the CC1 SIDE and the 12-PIN
wiring plug on the SAT SIDE. An intervening wall block can be used (normally placed at the SAT SIDE) to facilitate the connection.***

NOTE:

Figure 1-1

CC1 to SAT Interface

The RJ-45 wall block, represented in Fig­ure 1-1, can be obtained by ordering a Pelco
“KBDKIT”. In many cases, however, an

SAT

sys-

tem order will include several key-

pads in order to accommodate

more than one operator on

the

SAT SIDE

. Multiple key­pads are wired via the re­mote- keyboard, wiring plug.
In order to provide power to
the keyboard, a KBDKIT,
which includes a transformer,
is required, as power is not
provided at the remote port
itself. The kit, however, con­tains two wall blocks. Only
one wall block is needed to
wire the keypad. The “spare”
could be used here.

**

SATs

received in a system order are
assigned connection locations that are
found on your included port assignment
sheet(s). These indicate the CC1 Sercom
port to connect your

If you are adding the
system, you must

SAT

SAT

FIRST

to.

to an existing

do an across­the-board check of your system software
to ensure it is compatible with the version
levels required for satellite operation. The
information box on the first page of this
manual (

eters

9760 Operational Param-

) indicates the minimum version
levels of software required for satellite op­erations. If necessary, upgrade your as­sociated system and peripheral software.

Figure 1-2

Alternate CC1 to SAT Interface

***

An alternate method
is to strip the 8-conductor,
flat communication cable
to expose the necessary
communication wires and
then wire directly to the
wall plug, eliminating the
need for the wall block
(see below).

PHYSICAL INSTALLATION CM9760-SAT 1-1

1.1 9760 SIDE – CC1 TO WALL BLOCK

1. Determine the cable type (straight or reverse)* that
is provided or exists on-site that you want to use
between the RJ-45 Sercom connector on the CC1
and the wall block.

*see Figure 5-1 in Appendix I

2. Make the connection using Figure 1-3 as a guide.

1.2 SAT SIDE – WALL BLOCK TO SAT

1. Depending on the cable type used, wire the wall
block-to-SAT connection based on Figure 1-3 and
the included pin designation table. The 12-posi­tion wiring plug can be removed from the unit for
easy wiring access.

2. Strip and insert each wire to be connected in the
provided slot. Tighten firmly with a straight-slotted
screwdriver as shown.

Figure 1-3

Wall Block Connections

NOTE: The Comms configuration file in the
MGR program is used to set communication
parameters for the SAT connected to the
Sercom port (see SECTION 2, 3.1 COMMS
Files).

2.0 VIDEO TIE LINES

In order for the SAT to fulfill its function as a Satellite of the 9760 system, video interconnects, in the form of tie lines, must be run between the SAT
and the CM9760-MXB. The tie line–there must be at least one–has several uses. One function is to serve as a pathway for 9760 operators who want
to call up satellite camera displays via their 9760 system keyboards. The other is to provide a pathway for the programmed display (on 9760-system
monitors) of alarm-activated link cameras located on the SAT SIDE of the configuration.

2.1 9760 SIDE

The video tie lines coming from the SAT are connected to avail-
able, video input BNCs on the CM9760-MXB unit (see the NOTE
in Figure 1-4). Specifically note the physical port to which each
tie line is connected. You need this information later, when the
Cameras and Link Cameras configuration files (flat files) are pro­grammed on the 9760 SIDE of the configuration. These inputs
are treated differently so that they are recognized as tie lines and
not just regular video inputs.

2.2 SAT SIDE

You must also allocate at least one monitor-out on the SAT SIDE
of the configuration to tie line use. In most instances, you also
need one monitor-out for local SAT operation and programming.

IMPORTANT NOTE:

tor-out use is under user control, subject to the condi-

tion that at least one tie line exists and that the following
rule for multiple tie line hookup is obeyed: If you use
it must be connected to the
lines, they must be connected to the
monitor-outs, and so on.

sequential, ascending order to the monitor-outs on
the SAT. You may not “skip” around.

monitor-out for

LOCAL

use until all tie lines are configured first.

The ratio of tie line to local moni-

one

tie line,

MON 1

BNC. If you use

MON 1 and MON 2

Tie lines must be connected in

two

tie

BNC

Never configure a

Figure 1-4

Video Tie Line Hookup

1-2 C1510M-A (2/03) SECTION 1

3.0 ADDITIONAL SAT CONNECTIONS

If you want to operate and program from the local SAT SIDE of a
system configuration, a number of additional devices and connections
remain to be made. In order to view the results of local operations and
program SAT menus, a local monitor is needed.

3.1 LOCAL MONITOR

The local Monitor is used to display link camera call-ups and
switcher functions for local SAT operations. It is also used to
display the main program menu and its sub-menus during SAT
programming and setup. To install the local monitor:

1. Install the monitor.

2. Run a video output from the SAT to the installed monitor.

3.2 LINK OR SATELLITE CAMERAS (VIDEO INPUTS)

The CM9760-SAT can accommodate 16 video inputs that are
individually jumper-selectable for terminated or looping opera­tion. All video inputs are set to 75-ohm termination at the factory.
See Table A for typical coaxial video cable and recommended
distances. Use only coaxial cable specified for CCTV systems.
Run the video cables from the cameras or camera receivers to
the selected video inputs on the rear of the CM9760-SAT (the top
connector for each input pair).

Figure 1-5

Local SAT Monitor

Local SAT operation and control
functions are displayed here,
including the menus for SAT
programming. You should have
at least one local display available
to monitor local operations.
Depending on your application,
you can have up to three monitor-outs
configured for local use. Monitor functions
are chosen during programming
(see Section 2, Monitor Programming
Menu–page 2 of 3).

NOTE: If all monitor-outs
are set up as tie lines, SAT
menu programming is done
from the 9760-KBD.

Figure 1-6

Link (Satellite) Camera Inputs

3.2.1 Looping Video Inputs

As stated at the beginning of this manual, the loop-thru option is avail­able for each video input. If you want this option for any input, remove
the top cover of the unit and reposition the jumpers according to the
information provided in Figure 1-7.

Video Coaxial Cable Requirements

Table A

Cable Type Maximum Distance

RG-59U 750 ft. (228.6 m)
RG-6/U 1,000 ft. (304.8 m)
RG-11/U 1,500 ft. (457.2 m)
Consult factory Above 1,500 ft (457.2 m)

Figure 1-7

Loop-through Configuration

PHYSICAL INSTALLATION CM9760-SAT 1-3

3.3 RECEIVERS

If any camera you want to install is PTZ cap­able, then the receiver for that camera must be
individually wired for power and control (depen­dent on type). The CM9760-SAT has built-in
software that is individually selectable for each
camera control type. The correct protocol is se­lected via menu choices when programming the
Cameras menu for each individual input (see
Section 2,

2 of 2

able to utilize one of two communication proto­cols for connection to the SAT. One control type
is Coaxitron®. Coaxitron (standard or extended)
receivers utilize the input video line as a path
for sending control commands to the receiver.
The other control type is RS-422 “P” protocol
receivers that are wired independent of the
video path. RS-422 command control connec­tions originate at COM 1 o n the rear of the SAT
(see Figures 1 and 1-8).

Camera Programming Menu-Page

). Allowed camera control types must be

Figure 1-8

Receiver Wiring and Control

Figure 1-9

Alarm Wiring

3.4 ALARMS

The SAT has 16 alarm inputs, each designed for use with standard
single-pole, single-throw (SPST) switches. The alarm inputs on the
connector correspond, on a one-to-one basis, to the SAT’s 16 video
inputs; that is, video input 1 corresponds to alarm input 1, video
input 2 corresponds to alarm input 2, and so on. To properly recall
alarmed video, each alarm connection must correspond to the cor­rect video input. Each must also be appropriately programmed for a
number of variables. Refer to Section 2,

Alarm Programming

Menu-Page 1 of 1.

Connect the alarm inputs as illustrated in Figure
1-9. Alarms 1-9 use the indicated 12-pin con­nector (provided). For each alarm-video pair in­stalled and accounted for, wire a return ground
path. Utilize a ground connection located on the
same connector on which your alarm input is
wired. Proceed on a pair-by-pair basis until all
video-associated alarm pairs are wired. Utilize
both alarm wiring connectors, if necessary.

1-4 C1510M-A (2/03) SECTION 1

3.5 AUXS

There are three AUX outputs available through the control output wiring terminals located on the rear of the SAT. Aux operation and control are
for local SAT SIDE use only. Aux ouputs cannot be controlled from the 9760-KBD. These outputs are used to operate external devices. Each
output corresponds to a function key (F1-F3) on the KBD200/300/300V keyboard. The outputs can also be programmed to respond automati­cally to alarms. F1 is a Form C relay wired with a common (COM) and a normally open (N.O.) or normally closed (N.C.) contact. The other two
outputs (F2 and F3) are open collector transistor drivers that drive TTL circuits or low-current relays. If you use an external relay, make sure that
voltage and current requirements are well below maximum ratings. Exceeding specified values can permanently damage the transistors.
During programming, configure the auxiliary outputs to agree with the type of equipment you are using. Refer to Section 2,

Auxiliaries

Programming Menu-Page 1 of 1.

Follow the examples illustrated in
Figure 1-10 for wiring up the F1,
F2 and F3 relay contacts. The in­structions for wiring the F3 relay
are the same as those illustrated
for F2, if you substitute pins 8 and
9 for pins 6 and 7. When you fin­ish wiring the auxiliary outputs,
plug the wiring connector into the
control outputs terminal strip.

Figure 1-10

Aux Connections

3.6 LOCAL KEYPADS

The KBD200/300 may be connected to
the local keyboard port on the SAT and
used (in conjunction with the local moni­tor) for local SAT operations and program-
ming. The KBD300V cannot be used with
the local keyboard port as the matrix dis­play is not compatible with the voltages
supplied there. Connect the keyboard to
the local SAT keyboard port as indicated
in Figure 1-11. Additional keyboards may
be connected to the SAT unit using the
remote keyboard port (see Figure 1 and
reference Appendix II for information
on wiring the remote port).

Figure 1-11

Wiring the Local Keypad Port

PHYSICAL INSTALLATION CM9760-SAT 1-5

(This page intentionally left blank.)

1-6 C1510M-A (2/03) SECTION 1

SECTION 2 PRELIMINARIES

PRELIMINARIES ...................................................................... 2-1

1.0 SAT MENU PROGRAMMING ........................................ 2-5

PROGRAM MODE

Camera Programming Menu............................................. 2-6

Monitor Programming Menu ............................................. 2-8

Time-Date Programming Menu....................................... 2-11

Alarms Programming Menu ............................................ 2-12

Ports Programming Menu ............................................... 2-13

Auxiliaries Programming Menu ....................................... 2-14

Password Programming Menu........................................ 2-14

Access Programming Menu............................................ 2-15

You can program the CM9760-SAT from the SAT SIDE, using a local
keyboard and monitor, or you can program the SAT from the 9760
SIDE, using a 9760-KBD and a system monitor assigned to that opera­tor. These two basic programming methodologies are not, however,
mutually exclusive. By that, we mean, choosing to program from one
location does not necessarily exclude programming from the other. In­termediate variations to programming on just one side or the other are
possible.

NOTE:

The illustrations in this section represent the functional rela­tionships of the equipment mix needed to accommodate each pro­gramming choice that is discussed in the associated text.

2.0 OTHER SAT PROGRAMMING .................................... 2-16

OPERATIONAL MODE

Presets............................................................................ 2-16

Patterns........................................................................... 2-17

Zones .............................................................................. 2-18

3.0 9760 MGR-SAT PROGRAMMING .............................. 2-19

PROGRAMMING MODE

Comms File..................................................................... 2-19

Cameras File .................................................................. 2-20

Link Cameras File ........................................................... 2-20

Alarm File........................................................................ 2-21

Interspersed with these programming setups is the need to integrate
what is going to be programmed where, and by whom, given the various
configurations of equipment possible. In the illustrations and explana­tions below, we discuss some of these variations and indicate advan­tages, disadvantages and/or tradeoffs, if they exist, of each. We also
describe how to reach the main SAT programming menu from the given
programming location.

There are essentially three basic programming configurations. After we
look at those, we discuss a program variation.

NOTE:

In those instances where we discuss procedures or actions
yet to be covered in the manual, we either give a sufficiently adequate
(but abbreviated) discussion, or refer you to the appropriate manual
reference.

1. Programming Configuration I – Program the SAT from the SAT SIDE only.

This choice implies that at least one monitor-out line on the SAT SIDE is utilized as a local monitor and that you have a keyboard connected to the
SAT for programming purposes (see Figure 2-1).

(a) Initialize the keyboard to your local monitor (see Section 2,
(b) Press the PGM key on the KBD200 or 300.*
(c) Enter the password (default 2899100) and press the ACK key. This activates the main SAT programming menu.

Advantages:

accessible on the SAT SIDE of the configuration. The system user
can call up link cameras. Local SAT alarms can be viewed locally
and/or automatically reported to the system user. Associated SAT
alarm camera displays can be placed on tie lines for viewing on
system alarm monitors (this is the primary configuration that we
use when discussing SAT configuration, operation and program-
ming). It encompasses all the elements that the SAT is designed to
use and avoids programming from the system side, which is less
efficient.

Disadvantages:

eration and programming means someone must be stationed at
the satellite location to fully utilize its functions. If you are interested
only in alarm notification back to the system, you have, at most,
only three tie lines available, instead of four.

Local control and alarm notification operations are

From a system user viewpoint, local SAT op-

1.0 SAT MENU PROGRAMMING)

Figure 2-1

Programming Diagram One

*Although the KBD300V can be used for programming, we don’t

mention it here because (1) it can only be hooked up using the

SAT

keyboard remote port and (2) it requires a dedicated local
monitor-out line for its LCD display. The KBD300V is discussed in
APPENDICES II and III.

PRELIMINARIES

PROGRAMMING AND CONFIGURATION CM9760-SAT 2-1

2. Programming Configuration II – Use the same configuration and program the SAT from the 9760 SIDE.

The same equipment diagram used above is applicable here. Here, a
conscious choice is made to the program from the 9760 SIDE rather
than the SAT SIDE. If you want, programming chores can be split
between either side, although that is not recommended.

(a) Ensure no one else on the 9760 SIDE is using an SAT tie line.
(b) Ensure that the following items are in place:

1. The Link camera you plan to call** should already be in­cluded in the programmed Link Cameras file of the System
Manager (see Section 2,

2. The tie lines coming from the SAT to the MXB on the 9760
SIDE should be identified and programmed into the Sys­tem Manager’s Cameras file (see Section 2,

eras File)

(c) From the 9760 KBD, call up any link camera programmed in the

Link Camera file (see Section 3,

Cameras)

**

A link camera must be called as part of the programming process here. It is not necessary that the camera called be connected to the

.

.

3.3 Link Cameras File)

2.1 Selecting Link [Satallite]

.

3.2 Cam-

(d) Proceed to the DEF (define) sub-menu. (You may need to press

the ESC key first, then press the DEF key). If this is the first time
accessing that menu, enter the PIN (default 1234).See Figures
3-20 and 3-22 in Section 3,

3.2 9760 System-SAT Alarm Re-

sponse.

(e) Next, enter 89 into the 9760 keypad and then press the PRST

key (while still within the DEF menu). The main programming
menu of the SAT appears on the monitor in front of you.

Advantages:

the benefits of local SAT operation; therefore, someone not able to
program the SAT could, at least, operate SAT SIDE functions.

Disadvantages

SIDE, you must ensure that no one, other than the programmer, is

calling up any link cameras or otherwise utilizing any tie lines con­nected to the SAT. It’s possible for the SAT programming menu to
inadvertently appear on their monitor instead of the programmer’s
monitor.

You can program from the system side without losing

: Before initiating programming from the 9760

3. Programming Configuration III –

Programming from the 9760 SIDE only.

The programming setup for this configuration is illustrated in Figure
2-2. Note that all monitor-outs on the SAT SIDE are used as tie lines
that go to the 9760 SIDE.

With this configuration, the minimum hardware requirements before
programming can begin are as follows:

a. Monitor-outs from the SAT (tie lines) are connected to available

video inputs on the matrix bay on the 9760 SIDE (see the
“NOTE” about tie line connection in Section 1,

Lines

).
b. The COM line between the two pieces of equipment is in place.
c. You have a list of camera attributes for those cameras/receivers

that are or will be attached to the SAT. It is not necessary for
them to be physically attached to the SAT for programming to
be possible. When attached, however, the programmed attribute

for that input must correspond to the equipment connected.
d. The SAT is powered ON (plugged in).
e. The items listed in step 2b of the previous programming con-

figuration (the Comms, the Cameras and the Link Cameras con-

figuration files) are programmed and integrated into the 9760

System.

2.0 Video Tie

Figure 2-2

Programming Diagram Two

Once the 9760 System is initialized using the configuration files just
mentioned, you can proceed to program the SAT.

f. Repeat steps 2c, 2d, and 2e of Programming Configuration II.

Advantages:

system. All programming is done from the 9760 SIDE. The number
of tie lines available for operator access from the 9760 SIDE of the
configuration is at a maximum.

Disadvantages:

pabilities back to the head-end. Local satellite SAT SIDE operations
are not possible.

No operator is required on the SAT SIDE of the

You only use the SAT for its alarm reporting ca-

SAT

.

4. Unconventional Programming Configurations

Here we want to make some comments and put forth some suggestion about how you might use variations to the previous programming
configurations based upon how the 9760-SAT interface works. The following observations and general statements can be made:

1. As long as there is one tie line and a Com line in place between the SAT and the 9760 System, all attributes of SAT configuration can be

programmed from the 9760 SIDE via a preset call.

2. Normally, you should not initialize a keyboard (SAT SIDE) using a monitor-out line that has been configured as a tie line. However, under

certain circumstances, you might want to do this. The result of this action (from the SAT SIDE’s point of view) is that a monitor on the 9760

SIDE is used as a “substitute” local monitor for programming the SAT. The programming itself, however, is done from the 9760 SIDE.

Doing this allows one to program from the 9760 SIDE without using a preset call. Unfortunately, this can only be done if the operators on

both sides of the configuration can physically talk to each other during the programming process because the SAT SIDE must initiate and

exit the programming mode based on queues received from the 9760 SIDE.

3. Each side of the 9760-SAT configuration can be programmed independent of the other. Neither has to be physically connected to the other

for programming to be done as long as the programmed parameters of each match the physical parameters of the final equipment configu-

ration. System 9760-SAT related files (Comms, Link Cameras and Cameras) are programmed only from the 9760 SIDE of the configura-

tion. SAT menu software, however, can be programmed from either side of a configuration.

2-2 C1510M-A (2/03) SECTION 2

4a. Programming Variation Example: 9760-SAT Programming Minus Preset Call

This scenario illustrates the situation referenced in point 2, above.

The rationale for using this variation might be:

 The local SAT programmer is not sure of the correct parameters to enter; or,

 The local SAT programmer wants certain aspects of an operational or reprogrammed SAT to be checked by supervisory personnel located

on the 9760 SIDE of the configuration; or,

 The programmer on the SAT SIDE might be unavailable; no one on the 9760 SIDE remembers the preset call function or remembers how

to use it, and so on.
Proceed as follows:
1 From the 9760 SIDE, ensure that no one, other than the person doing the programming, is using a tie line for any purpose.

2. Call up a satellite camera to a viewable system monitor. Use the logical number for the referenced camera.

NOTE:

The operator on the

NOTE:

It is not necessary for the called camera to actually be attached on the

9760 SIDE

and on the

SAT SIDE

must have some independent means of communicating with each other.

SAT SIDE

.

All you are doing here is tying up a tie line to your

reference monitor so that anything put on the tie line can be viewed from that display.

a. Initialize or reinitialize (as the case may be) the KBD on the SAT SIDE; use a monitor-out number that has been allocated

as a tie line.

NOTE:

More than likely, you would use MON 1, as the object here is to match the monitor -out line initialized on the

SAT SIDE

video tie line secured or referenced on the system side in step 2. The 9760 system normally grabs the first tie line available. Since no
tie lines are allocated for use but the one we called, it should be the one connected to the MON 1 output from the SAT. This tie line
should correspond to the first video input configured in the Cameras file as a tie line for the SAT.

b. On the SAT SIDE, enter program mode as usual:

1) Press the PGM key
A “P” appears on the KBD LED display.

2) Enter the password (default 2899100) and ACK it.

c. The program menu should appear on the system-side monitor selected in step 2. The operator on the 9760 SIDE can now check,

correct, add, subtract or otherwise change all attributes of the SAT menu system. When all changes are made and the operator
attempts to exit the menu using choice (9) in the menu, the display reverts to the SAT’s program PASSWORD menu, which flashes
intermittently on the monitor display. At this time, the only way to exit the program is for the operator on the SAT SIDE to press the ACK
key. Once this is done the SAT operator should immediately reinitialize the SAT keyboard to the local SAT monitor display .

with the

Figure 2-3

Programming Diagram Three

INFORMATION BOX

The coordination issue in this example could be avoided if you ran a
KBD200/KBD300 from the remote keyboard port located on the rear
of 9760-SAT back to the head-end, or 9760 SIDE of the configu­ration. Then program entry and exit could also be handled by the
9760 operator. In essence, this would amount to doing local SAT
SIDE programming from the 9760 SIDE of the configuration.
Program entry and exit would use the KBD300 and SAT program-
ming would use the 9760KBD. See Figure 2-3.

COMMENTS

With reference to Figure 2-3 and the Information Box above, we
can make the following observation:

To persist in programming the SAT from a 9760 keyboard when a KBD300
is available on the 9760 SIDE is just a convoluted version of Program-
ming Configuration I. Even so, there are some advantages to con­sider for this configuration:

1. You can program the SAT from the 9760 SIDE without using a preset call function.

2. You can use the KBD300, rather than the 9760 keyboard for SAT programming. The KBD300 is more efficient for programming SAT menus.

3. You can still control local SAT functions from the 9760 SIDE and eliminate the need for a downstream operator.

PROGRAMMING AND CONFIGURATION CM9760-SAT 2-3

PRELIMINARIES

SECTION 2 PROGRAMMING AND CONFIGURATION

1.0 SAT MENU PROGRAMMING

Prior to programming the SAT, check to ensure that the bulleted items in the two lists below are either taken care of or that the required
information is readily at hand**. All items in the first list are required.

**The checklist below is based on “

• The SAT-9760 communication interface is in place and correctly wired (see Section 1,

• Identify and make a list of the monitor-out connections on the SAT that are going to be used as tie lines to the CM9760-CC1.

• Make sure you have a monitor attached to the SAT that you can use as your local programming monitor.

• Ensure that a KBD200 or KBD300 (with satellite software) is attached to the local keyboard port on the SAT.

It is important to have the information for the following items before programming the attributes of the item in question. Programming menus for
devices that connect to the SAT can take place before the device is attached, but all devices configured and referenced in the menus should
be connected prior to system operation. Once the system is operational, programming menus for the SAT can be accessed and edited for
currently attached equipment. Care must be taken, however, when making these changes or when attaching additional equipment. If you make
menu choices or device additions that affect the 9760 SIDE of the 9760-SAT interface, remember that you may also have to change existing
configuration files because of these changes. These, in turn, might require interruption of the 9760-SA T communication link and anything else
connected to the 9760 system while new configuration files are loaded.

• Ensure that video inputs to the SAT (link or satellite cameras) are identified as to type (fixed or PTZ). If the receiver is PTZ capable, the
receiver control type should be known (coaxitron or “P” type [RS-422] ).

• Hard-wired alarm and aux configurations.

Programming Configuration I

” located in

Section 2’s

Physical Installation, 1.0 Com Connection

preliminary discussion.

).

LOCAL KEYBOARD INITIALIZATION

Initialization is necessary after power is first applied to the keyboard (SAT SIDE), or if power is cycled on

Figure 2-4

Initialization Screen

the unit or if an operator-induced reset is invoked (see Section 5, Appendix V,

ment)

. When power is applied, the LCD display flashes momentarily, and then goes blank. Initialization
consists of entering the # of the local monitor in the keypad and pressing the MON key. You can do this
immediately after power is applied or you can wait five seconds and then enter the # and press the MON
key. In either case, the result is a 5 second delay before the display of camera input 1 (by default) appears
on the monitor along with other character display information (see Figure 2-4).

The 01 is the camera number. CAM1 is the default camera title. Other information that might appear (time/
date information, for example) does not appear now (the first time through) because of program menu
defaults.

If you have a local monitor attached, but do not yet have any cameras attached, this will not prevent you
from programming the unit. Your programming screens will appear on the local monitor as soon as the
PGM key is pressed, as you will soon see. Programming SAT menus can now proceed.

Default Reset Assign-

2-4 C1510M-A (2/03) SECTION 2

A WORD ABOUT THE MENU DISCUSSION LAYOUT

The menu discussion is split into three columns. At the top, far right side of each page, the SAT main menu is displayed and the sub-menu under
discussion is highlighted. Tagged, drop-down arrows below that, indicate approximately where, within the sub-menu being programmed, that the
referenced sub-menu is discussed. These comments appear in the middle column. The far left column displays a KBD300 template, whose keyboard
movements are highlighted, to indicate the keyboard movements necessary to invoke the program operation(s) being discussed in the adjacent
columns. These conventions are illustrated below.

Figure 2-5

Menu Discussion Conventions

INFORMATION BOX

Programming SAT menus from the CM9760-KBD.
All columns in the menu discussion layout except the far left one, where

keypad movement on a KBD300 is illustrated, are applicable to anyone
programming direct from the 9760 keyboard.

The information contained in the sub-sections entitled

figuration II
PRELIMINARIES,

order to arrive at the SAT main programming menu (see the Camera
Progamming Menu – Page 1 of 2).

The joystick affects cursor movement and some sub-menu selections.
Otherwise, the “Iris” Open/Close button effects item choices. Unlike the
KBD300 keypad, you cannot revert to the main menu using a PGM key
and you cannot choose a numbered selection by pressing a “numbered”
key, nor can you ACK an item: you have no “shortcut” keys. But you can
program the menus. Perhaps not as quickly, but you still can get the job
done.

and

Programming Configuration III

instructs the 9760-KBD user on the steps to follow in

Programming Con-

, located in SECTION 2,

PROGRAMMING AND CONFIGURATION CM9760-SAT 2-5

JOYSTICK

OPEN/CLOSE
IRIS BUTTON

2-6 C1510M-A (2/03) SECTION 2

PROGRAMMING AND CONFIGURATION CM9760-SAT 2-7

2-8 C1510M-A (2/03) SECTION 2

The remaining line(s) can be configured as desired,

PROGRAMMING AND CONFIGURATION CM9760-SAT 2-9

NOTE: The alarm settings in the monitor menu (including
alarm enable) for monitor 04 (LOCAL MODE ONLY) are the
Aux “alarm follow” sources referenced when configuring alarm
activation of AUXs (see Aux Programming Menu Page 1 of 1).

2-10 C1510M-A (2/03) SECTION 2