Pelco C497M-D User Manual

®

HS4000

High-Security Enclosure

Installation/Operation Manual

C497M-D (1/96)

Pelco • 3500 Pelco Way • Clovis, CA 93612-5699 • USA • www.pelco.com

[phone] or (1-559) 292-1981 • FAX [phone] or (1-559) 292-3827

International Customers: Tel [phone] • FAX [phone]

TABLE OF CONTENTS

Section Page

1.0 WARNINGS..................................................................................................................................... 1

2.0 SCOPE ............................................................................................................................................2

2.1 DESCRIPTION ...................................................................................................................... 2

3.0 INSTALLATION ...............................................................................................................................3

3.1 CAMERA/LENS INSTALLATION...........................................................................................3

4.0 TAMPER SWITCH INSTALLATION ................................................................................................ 4

4.1 WIRING THE SWITCH ..........................................................................................................4

5.0 CARE AND MAINTENANCE ...........................................................................................................4

6.0 SPECIFICATIONS ..........................................................................................................................4

7.0 EXPLODED ASSEMBLY DIAGRAM ...............................................................................................5

7.1 MECHANICAL PARTS LIST .................................................................................................. 5

8.0 WARRANTY AND RETURN INFORMATION ................................................................................. 6

LIST OF ILLUSTRATIONS

Figure Page

1 HS4000 Dimension Drawing ...........................................................................................................2

2 HS4000 Series Tamper Switch Installation ..................................................................................... 4

3 HS4000 Exploded Assembly Diagram ............................................................................................5

REVISION HISTORY

Manual # Date Comments

C497M 6/90 Original manual.
C497M 10/92 Rev. A. Revised manual to reflect new style; including isometric

diagrams.

C497M-B 7/95 Rev. B. Manual revised to include tamper switch information and new

manual layout design.

C497M-C 11/95 Rev. C. Revised to include updated tamper switch/bracket part numbers

and exploded view diagram.

C497M-D 1/96 Rev. D. Revised to include tamper switch installation, specification

description and new part numbers per ECO 95-397.

11/96 Revised to include updated mechanical parts list and exploded assembly

diagram.

Pelco, the Pelco Logo, Camclosure, Esprit, Genex, Legacy, and Spectra are registered trademarks of Pelco. © Copyright 1996, Pelco. All rights reserved.
Endura and ExSite are trademarks of Pelco.

ii

8 Pelco Manual C497M-D (1/96)

INSTALLATION/OPERATION MANUAL
HS4000 HIGH-SECURITY ENCLOSURE

1.0 WARNINGS

Prior to installation and use of this product, the following
WARNINGS should be observed.

1. Installation and servicing should only be done by
Qualified Service Personnel and conform to all
Local codes.

2. Unless the unit is specifically marked as a NEMA
Type 3, 3R, 3S, 4, 4X, 6, or 6P enclosure, it is
designed for indoor use only and it must not be
installed where exposed to rain and moisture.

3. Only use replacement parts recommended by
PELCO.

The product may bear the following
marks:

This symbol indicates that dangerous voltage
constituting a risk of electric shock is present

within this unit.

4. After replacement/repair of this unit’s electrical
components, conduct a resistance measurement
between line and exposed parts to verify the exposed
parts have not been connected to line circuitry.

5. The installation method and materials should be
capable of supporting four (4) times the weight of
the enclosure, pan/tilt, camera and lens combination.

This symbol indicates that there are important
operating and maintenance instructions in the

literature accompanying this unit.

CAUTION:

TO REDUCE THE RISK OF ELECTRICAL
SHOCK, DO NOT REMOVE COVER. NO
USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.

RISK OF ELECTRIC SHOCK.

CAUTION:

DO NOT OPEN.

Please thoroughly familiarize yourself with the information in this manual

prior to installation and operation.

Pelco Manual C497M-D (1/96) 1

2.0 SCOPE

The information contained within this manual covers
the HS4000 High Security Camera Enclosure.

2.1 DESCRIPTION

The HS4000 is a high-security camera enclosure de­signed for use with 2/3-inch cameras and will accom­modate fixed focal length lenses or motorized zoom
lenses with or without auto-iris operation.

The HS4000 has been engineered for indoor use as a
stand-alone enclosure in prisons, detention cells, or
other applications requiring maximum protection from
vandalism.

This enclosure has a removable rear cap for easy ac­cess to the slide-out platform on which the camera is
mounted. The removable front cap allows manual lens
adjustments to be made without removing the camera.
Access to the interior can only be gained with a spe­cially designed tool, eliminating the possibility of the
enclosure being opened by unauthorized personnel.

A factory-installed tamper switch provides additional
security.

Figure 1. HS4000 Dimension Drawing

2 Pelco Manual C497M-D (1/96)

3.0 INSTALLATION

3.1 CAMERA/LENS INSTALLATION

The following hardware is supplied with the enclosure
and can be used to mount the enclosure or the camera/
lens:

Quantity Item

2 1/4-20 x .500 hex head screws
4 1/4 flat washers
4 1/4 split washers
2 1/4-20 “tampruf” screws

1. Remove the four (4) “tampruf” screws from the
rear cap with the tool provided.

2. Remove the rear cap from the enclosure. Loosen
the bolt on the camera sled assembly and remove
it from the rail.

3. Place the camera/lens on the sled assembly.

NOTE: Position the camera/lens at the
forward-most point on the sled, while al­lowing clearance between the lens and en­closure window when the lens is adjusted
to its maximum physical length.

4. Secure the camera/lens to the sled with the 1/4-20
hex head screws provided.

5. Pull the video and power cables through the knock­outs and attach to the camera.

6. Adjust camera focus and iris if necessary.

7. Replace the sled onto the rail and slide the assem­bly into the enclosure; replace the bolt and secure.

8. Replace the rear cap and the four (4) “tampruf”
screws.

9. Attach the enclosure to the appropriate mount or
pan/tilt using the instructions provided.

NOTE: If the lens needs to be adjusted fur­ther after installation has been completed, it is
easier to remove the front cap to make final lens
adjustments.

Pelco Manual C497M-D (1/96) 3

4.0 TAMPER SWITCH INSTALLATION

6.0 SPECIFICATIONS

The HS4000 High-Security enclosures come standard
from the factory with a tamper switch(es) mounted on
the secured access door. Refer to Section 4.1 for wir­ing.

Should it become necessary to install a replacement
switch, reference Figure 2 and perform the following
steps:

1. Open the enclosure by removing the end plate from
the desired “alarmed” opening.

2. Install the bracket so that the mounting studs go
through the slots in the bracket.

NOTE: The slot in the bracket allows the switch
to be used against either the 1/2" (1.27 cm) thick
lexan window or the .134" (0.34 cm) thick metal
plate.

3. If the switch is to be used against the metal plate,
slide the bracket so that the studs are at the end of
the slot that is furthest from the switch plunger.

4. If the switch is to be used against the Lexan win­dow, slide the bracket so that the studs are at the
end of the slot nearest the switch plunger.

5. When reinstalling the front/rear plate, position the
plate flush with the end of the enclosure body.

MECHANICAL

Camera
Mounting: Multiple holes on camera sled
Viewing
Window: 1/2" (1.27 cm) thick impact and abra-

sion resistant Lexan

Camera Size: Accommodates camera/lens combi-

nations up to:

6.00" W x 4.75" H x 15.00" L
(15.24 cm x 12.07 cm x 38.10 cm)

Tamper Switch: Plunger type door switch with “pull

to cheat” feature. N.O/N.C. contacts
clearly marked on body of switch.
DM electrical rating: 10A, 125V.

Security: Tamper-resistant screws N.O./N.C.

switch contact on secure cover

ELECTRICAL

Cable Entry: Two (2) cable knockout holes on rear

plate

Tamper Switch: 1/4" (.63 cm) quick connect. N.O./

N.C. clearly marked on switch body.
10A, maximum switching current
125V, maximum switching voltage.

GENERAL

Construction: Seam welded 10 gauge .134" (0.34

cm) steel
Finish: Poly vinyl powder coat
Dimensions: See Figure 1
Weight: 22 lbs (9.9 kg)

4.1 WIRING THE SWITCH

The tamper switch comes with both a “Normally Open”
contact and a “Normally Closed” contact.

• For a “Normally Open” circuit, use the “open” and
“common” terminals.

• For a “Normally Closed” circuit, use the “closed”
and “common” terminals.

5.0 CARE AND MAINTENANCE

Regularly scheduled maintenance will help prolong the
appearance of the equipment.

Clean the window regularly with a soft cloth and mild
nonabrasive detergent in water to help maintain picture
clarity.

4 Pelco Manual C497M-D (1/96)

(Product specifications subject to change
without notice.)

Figure 2. HS4000 Series Tamper Switch Installation

7.0 EXPLODED ASSEMBLY DIAGRAM

Figure 3. HS4000 Exploded Assembly Diagram

7.1 MECHANICAL PARTS LIST

Item Quantity Description Part Number

1 1 Lexan window AH80001001
2 1 Body assembly HS40001100WA
3 2 Front/rear plate HS40004003COMP
4 1 Sled EH40144001COMP
5 1 Knockouts plate HS40004015COMP
6 2 Tamper switch bracket HS30004113COMP
7 2 Tamper switch SWI1DM401
8 10 Screws, “tampruf” #10, SS, 1/4-20 x 1/2" round ZH1/4-20X.50SRT
9 1 Socket, “tampruf” #10 ZTSOCKET10

A 4 1/4-20 Nut-lock ZH1/420NUTCHN
B 16 1/4" Flat washer ZH260X562X65C
C 1 1/4-20 x 1.25" Screw ZH1/420X1.25CS
D 4 1/4" Split lock washer ZH1/4LWSSL
E 4 1/4-20 Hex nut ZH1/4-20 NUTCH

F 4 #6 Lock washer ZH6LWSIS

G 4 6-32 Hex nut ZH6-32NUTSH

Pelco Manual C497M-D (1/96) 5

8.0 WARRANTY AND RETURN
INFORMATION

WARRANTY

Pelco will repair or replace, without charge, any merchandise proved
defective in material or workmanship for a period of one year after the date
of shipment.

Exceptions to this warranty are as noted below:

• Five years on FT/FR8000 Series fiber optic products.

• Three years on Genex

keyboard).

• Three years on Camclosure

CC3701H-2, CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2,
and MC3651H-2X camera models, which have a five-year warranty.

• Two years on standard motorized or fixed focal length lenses.

• Two years on Legacy®, CM6700/CM6800/CM9700 Series matrix, and

DF5/DF8 Series fixed dome products.

• Two years on Spectra

ing when used in continuous motion applications.

• Two years on Esprit

wiper blades).

• Eighteen months on DX Series digital video recorders, NVR300

Series network video recorders, and Endura
network-based video products.

• One year (except video heads) on video cassette recorders (VCRs).

Video heads will be covered for a period of six months.

• Six months on all pan and tilts, scanners or preset lenses used in

continuous motion applications (that is, preset scan, tour and auto scan
modes).

Pelco will warrant all replacement parts and repairs for 90 days from the
date of Pelco shipment. All goods requiring warranty repair shall be sent
freight prepaid to Pelco, Clovis, California. Repairs made necessary by
reason of misuse, alteration, normal wear, or accident are not covered
under this warranty.

Pelco assumes no risk and shall be subject to no liability for damages or
loss resulting from the specific use or application made of the Products.
Pelco’s liability for any claim, whether based on breach of contract,
negligence, infringement of any rights of any party or product liability,
relating to the Products shall not exceed the price paid by the Dealer to
Pelco for such Products. In no event will Pelco be liable for any special,
incidental or consequential damages (including loss of use, loss of profit
and claims of third parties) however caused, whether by the negligence
of Pelco or otherwise.

The above warranty provides the Dealer with specific legal rights. The
Dealer may also have additional rights, which are subject to variation from
state to state.
If a warranty repair is required, the Dealer must contact Pelco at (800)
289-9100 or [phone] to obtain a Repair Authorization number
(RA), and provide the following information:

1. Model and serial number

2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice

number

3. Details of the defect or problem If there is a dispute regarding the

warranty of a product which does not fall under the warranty conditions
stated above, please include a written explanation with the product
when returned.

Method of return shipment shall be the same or equal to the method by
which the item was received by Pelco.

®

Series products (multiplexers, server, and

®

and fixed camera models, except the

®

, Esprit®, ExSite™, and PS20 scanners, includ-

®

and WW5700 Series window wiper (excluding

™

Series distributed

RETURNS

In order to expedite parts returned to the factory for repair or credit, please
call the factory at [phone] or [phone] to obtain an
authorization number (CA number if returned for credit, and RA number
if returned for repair).

All merchandise returned for credit may be subject to a 20% restocking
and refurbishing charge.

Goods returned for repair or credit should be clearly identified with the
assigned CA or RA number and freight should be prepaid. Ship to the
appropriate address below.

If you are located within the continental U.S., Alaska, Hawaii or Puerto
Rico, send goods to:

Service Department
Pelco
3500 Pelco Way
Clovis, CA 93612-5699

If you are located outside the continental U.S., Alaska, Hawaii or Puerto
Rico and are instructed to return goods to the USA, you may do one of the
following:

If the goods are to be sent by a COURIER SERVICE, send the goods to:

Pelco
3500 Pelco Way
Clovis, CA 93612-5699 USA

If the goods are to be sent by a FREIGHT FORWARDER, send the goods
to:

Pelco c/o Expeditors
473 Eccles Avenue
South San Francisco, CA 94080 USA
Phone: [phone]
Fax: [phone]

This equipment contains electrical or electronic components that must be recycled properly to comply with Directive 2002/96/EC of the European Union
regarding the disposal of waste electrical and electronic equipment (WEEE). Contact your local dealer for procedures for recycling this equipment.

6 Pelco Manual C497M-D (1/96)