Pelco C3410M User Manual

C3410M (2/06) DEMOKIT-MINI/DEMOKIT-MINADPT

Spectra® Mini Demo Kit

The DEMOKIT-MINI and the DEMOKIT-MINADPT are designed for demonstrating the Spectra Mini dome system.

The DEMOKIT-MINI is a complete kit and includes the following parts:

1 Base assembly 1 Tube 1 Head assembly 2 Power cords (1 USA standard and 1 European standard)

The DEMOKIT-MINADPT contains the head assembly only. It is designed to adapt the Spectra III™/Spectra III SE demonstration kit for use with the Spectra Mini dome system.

To assemble the demonstration kit:

1. Connect the electrical connector in the bottom of the tube to the electrical connector in the base assembly. Place the tube on the base assembly and tighten the set screws to secure the tube to the base.

2. Connect the electrical connector in the head assembly to the electrical connector in the top of the tube, and then fit the head assembly onto the top of the tube. Tighten the set screws.

3. Connect the BNC connector and the RJ45-10 connector in the head assembly to a Spectra Mini dome, and then attach the dome system to the head assembly with the screws provided in the head assembly.

4. Connect a monitor, KBD300A keyboard, and power (make sure the voltage selection switch is in the proper position before applying power to the unit). A terminal block is provided for daisy-chaining equipment.

TIGHTEN SET SCREWS TO SECURE ASSEMBLY

POWER OUT TO MONITOR

VIDEO

OUT

KEYBOARD

VIDEO OUT TO MONITOR

MONITOR

POWER OUT

KBD300A INPUT

COM

RXRX+

2 WIRE CONTROL, D OR P PROTOCOL

ON/OFF SWITCH

NOTE: Demonstration unit only, no certification required.

FUSE COVER

POWER IN

115 VAC

230 VAC

NOTE: Extra fuses are supplied with the equipment. To change the fuse, use a small screwdriver and remove the fuse cover.

IMPORTANT: This product is factory

set to operate at 115 VAC. For 230 VAC operation, move the switch to the 230 VAC position before applying power to the unit.

Pelco World Headquarters • 3500 Pelco Way • Clovis, California 93612 USA • www.pelco.com

USA & Canada • Tel: 800/289-9100 • Fax: 800/289-9150

International • Tel: 1-559/292-1981 • Fax: 1-559/348-1120

PRODUCT WARRANTY AND RETURN INFORMATION

WARRANTY

Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment.

Exceptions to this warranty are as noted below:

• Five years on FT/FR8000 Series ﬁber optic products.

• Three years on Genex

• Three years on Camclosure CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2, and MC3651H-2X camera models, which have a ﬁve-year warranty.

• Three years on PMCL 200/300/400 Series LCD monitors.

• Two years on standard motorized or ﬁxed focal length lenses.

• Two years on Legacy ﬁxed dome products.

• Two years on Spectra continuous motion applications.

• Two years on Esprit

• Two years (except lamp and color wheel) on Digital Light Processing (DLP The lamp and color wheel will be covered for a period of 90 days. The air ﬁlter is not covered under warranty.

• Eighteen months on DX Series digital video recorders, NVR300 Series network video recorders, Endura twisted pair transmission products.

• One year (except video heads) on video cassette recorders (VCRs). Video heads will be covered for a period of six months.

• Six months on all pan and tilts, scanners or preset lenses used in continuous motion applications (that is, preset scan, tour and auto scan modes).

Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco shipment. All goods requiring warranty repair shall be sent freight prepaid to Pelco, Clovis, California. Repairs made necessary by reason of misuse, alteration, normal wear, or accident are not covered under this warranty.

Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from the speciﬁc use or application made of the Products. Pelco’s liability for any claim, whether based on breach of contract, negligence, infringement of any rights of any party or product liability, relating to the Products shall not exceed the price paid by the Dealer to Pelco for such Products. In no event will Pelco be liable for any special, incidental or consequential damages (including loss of use, loss of proﬁt and claims of third parties) however caused, whether by the negligence of Pelco or otherwise.

The above warranty provides the Dealer with speciﬁc legal rights. The Dealer may also have additional rights, which are subject to variation from state to state.

Series products (multiplexers, server, and keyboard).

and ﬁxed camera models, except the CC3701H-2,

, CM6700/CM6800/CM9700 Series matrix, and DF5/DF8 Series

, Esprit®, ExSite™, and PS20 scanners, including when used in

and WW5700 Series window wiper (excluding wiper blades).

™

Series distributed network-based video products, and TW3000 Series

) displays.

If a warranty repair is required, the Dealer must contact Pelco at (800) 289-9100 or (559) 292-1981 to obtain a Repair Authorization number (RA), and provide the following information:

1. Model and serial number

2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number

3. Details of the defect or problem

If there is a dispute regarding the warranty of a product which does not fall under the warranty conditions stated above, please include a written explanation with the product when returned.

Method of return shipment shall be the same or equal to the method by which the item was received by Pelco.

RETURNS

In order to expedite parts returned to the factory for repair or credit, please call the factory at (800) 289-9100 or (559) 292-1981 to obtain an authorization number (CA number if returned for credit, and RA number if returned for repair).

All merchandise returned for credit may be subject to a 20% restocking and refurbishing charge.

Goods returned for repair or credit should be clearly identiﬁed with the assigned CA or RA number and freight should be prepaid. Ship to the appropriate address below.

If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico, send goods to:

Service Department Pelco 3500 Pelco Way Clovis, CA 93612-5699

If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico and are instructed to return goods to the USA, you may do one of the following:

If the goods are to be sent by a COURIER SERVICE, send the goods to:

Pelco 3500 Pelco Way Clovis, CA 93612-5699 USA

If the goods are to be sent by a FREIGHT FORWARDER, send the goods to:

Pelco c/o Expeditors 473 Eccles Avenue South San Francisco, CA 94080 USA Phone: 650-737-1700 Fax: 650-737-0933

This equipment contains electrical or electronic components that must be recycled properly to comply with Directive 2002/96/EC of the European Union regarding the disposal of waste electrical and electronic equipment (WEEE). Contact your local dealer for procedures for recycling this equipment.

REVISION HISTORY

Manual # Date Comments

C3410M 2/06 Original version.

Pelco, the Pelco logo, Spectra, Genex, Legacy, Esprit, and Camclosure are registered trademarks of Pelco. © Copyright 2006, Pelco. All rights reserved. Endura and ExSite are trademarks of Pelco. DLP is a registered trademark of Texas Instruments, Inc.