Pelco C2913M-F, MC3710 User Manual

Installation/Operation

MC3610 and MC3710 Series
Black-White Camera

C2913M-F (08/05)

Pelco Worldwide Headquarters • 3500 Pelco Way, Clovis, CA 93612-5699 USA • www.pelco.com

USA & Canada: Tel [phone] • FAX [phone]
International: Tel: [phone] • FAX [phone]

® Pelco, the Pelco logo, Spectra, Genex, Legacy, Esprit and Camclosure are registered trademarks of Pelco.

[ 2 ] Pelco Manual C2913M-F (08/05)

™Endura and ExSite are trademarks of Pelco

™DLP is a trademark of T exas Instruments, Inc.

™SuperHAD CCD is a trademark of the Sony Corporation.

© Copyright 2005, Pelco. All rights reserved.

CONTENTS

IMPORTANT SAFETY INSTRUCTIONS ........................................................................................................... 4

REGULATORY NOTICES ................................................................................................................................. 5

DESCRIPTION................................................................................................................................................... 5

Models ........................................................................................................................................................... 5

CAMERA LAYOUT............................................................................................................................................. 6

INSTALLATION .................................................................................................................................................. 6

Lens Mounting ............................................................................................................................................... 6

Camera Mounting .......................................................................................................................................... 7

CONNECTIONS................................................................................................................................................. 7

Video Connections ........................................................................................................................................ 7

Power Connections ....................................................................................................................................... 8

Genlock Connection (MC3710H Series Only) ............................................................................................ 10

RJ45-10 Connections...................................................................................................................................11

Service Connection ..................................................................................................................................... 12

CAMERA SETUP ............................................................................................................................................. 13

Lens Setup and Focus Procedures............................................................................................................. 13

Back Focus Adjustment............................................................................................................................... 14

Switch Settings ............................................................................................................................................ 15

Camera Synchronization ............................................................................................................................. 17

SPECIFICATIONS ........................................................................................................................................... 18

WARRANTY AND RETURN INFORMATION .................................................................................................22

LIST OF ILLUSTRATIONS

1 Camera Layout...............................................................................................................................6

2 AID/AIV Lens Connector................................................................................................................6

3 Camera Mounting...........................................................................................................................7

4 Genlock Daisy-chain Connection ............................................................................................... 10

5 RJ45-10 Connector......................................................................................................................11

6 Service Connector ...................................................................................................................... 12

7 AGC and ESC Switch Settings................................................................................................... 13

8 Back Focus Adjustment .............................................................................................................. 14

9 Switch Settings ........................................................................................................................... 15

LIST OF TABLES

A Video Coaxial Cable Requirements ...............................................................................................7

B Wiring Distances for 5 VA Cameras (24 VAC/12 VDC) ................................................................ 9

C RJ45-10 Pinouts ..........................................................................................................................11

Pelco Manual C2913M-F (08/05) [ 3 ]

IMPORTANT SAFETY INSTRUCTIONS

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including

amplifiers) that produce heat.

9. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles,

and the point where they exit from tha apparatus.

10. Only use attachments/accessories specified by the manufacturer.

11. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold

with the apparatus. When a cart is used, use caution when moving the cart/apparatus
combination to avoid injury from tip-over.

12. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been

damaged in any way, such as when the power supply cord or plug is damaged, liquid has been spilled or
objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, the apparatus
does not operate normally, or the apparatus has been dropped.

13. Apparatus shall not be exposed to dripping or splashing, and no objects filled with liquids, such as vases,

shall be placed on the apparatus.

14. WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.

15. Installation should be done only by qualified service personnel and conform to all local codes.

16. Unless the unit is specifically marked as a NEMA Type 3, 3R, 3S, 4, 4X, 6, or 6P enclosure, it is designed

for indoor use only and it must not be installed where exposed to rain and moisture.

17. Use only installation methods and materials capable of supporting four times the maximum specified load.

18. CAUTION: These servicing instructions are for use by qualified personnel only. To reduce the risk of

shock, do not perform any servicing other than that contained in the operating instructions unless you are
qualified to do so.

19. Only use replacement parts recommended by Pelco.

20. Only power 12 VDC/24 VAC cameras from a UL Listed Class 2 power supply.

21. For outdoor use, an appropriate protective housing conforming to IP65 or better must be used. For UL, a

UL Listed enclosure suitable for the application must be used.

22. DD/AI Lens Connector
The maximum load for a direct drive lens must not exceed 25 mA
The maximum load for an auto iris lens must not exceed 50 mA.

This symbol indicates that dangerous voltage
constituting a risk of electric shock is present
within this unit.

This symbol indicates that there are impor­tant operating and maintenance instructions
in the literature accompanying this unit.

Please thoroughly familiarize yourself with the information in this manual prior to installation and
operation.

[ 4 ] Pelco Manual C2913M-F (08/05)

REGULATORY NOTICES

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.

RADIO AND TELEVISION INTERFERENCE
MC3610H-6, MC3610H-6X, MC3610H-7, MC3710S-6, MC3710S-6X, MC3710S-7, MC3710H-6, MC3710H­6X and MC3710H-7 models:

This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However there is no guarantee that the interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.
You may also find helpful the following booklet, prepared by the FCC: “How to Identify and Resolve Radio-TV

Interference Problems.” This booklet is available from the U.S. Government Printing Office, Washington D.C.

20402.
This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

DESCRIPTION

MC3610 and MC3710 Series cameras are black-white video cameras with a 1/3-inch CCD imager. All cameras
have a direct drive/auto iris lens connector and adjustable back focus, and they accept C and CS lenses.

Models

MC3610H-6 High resolution (570 TV lines), Exview HAD™ CCD, 0.04 lux at F1.2, EIA, 12 VDC/24 VAC
MC3610H-6X High resolution (570 TV lines), Exview HAD™ CCD, 0.04 lux at F1.2, CCIR, 12 VDC/24 VAC
MC3610H-7 High resolution (570 TV lines), Exview HAD™ CCD, 0.04 lux at F1.2, EIA, 110-240 VAC
MC3610H-7X High resolution (570 TV lines), Exview HAD™ CCD, 0.04 lux at F1.2, CCIR, 110-240 VAC
MC3710S-6 Standard resolution (380 TV lines), SuperHAD™ CCD, 0.06 lux at F1.2, EIA, 12 VDC/24 VAC
MC3710S-6X Standard resolution (380 TV lines), SuperHAD™ CCD, 0.06 lux at F1.2, CCIR, 12 VDC/24 VAC
MC3710S-7 Standard resolution (380 TV lines), SuperHAD™ CCD, 0.06 lux at F1.2, EIA, 110-240 VAC
MC3710S-7X Standard resolution (380 TV lines), SuperHAD™ CCD, 0.06 lux at F1.2, CCIR, 110-240 VAC
MC3710H-6 High resolution (570 TV lines), SuperHAD™ CCD, 0.07 lux at F1.2, EIA, Genlock, 12 VDC/24 VAC
MC3710H-6X High resolution (570 TV lines), SuperHAD™ CCD, 0.07 lux at F1.2, CCIR, Genlock, 12 VDC/24 VAC
MC3710H-7 High resolution (570 TV lines), SuperHAD™ CCD, 0.07 lux at F1.2, EIA, Genlock, 110-240 VAC
MC3710H-7X High resolution (570 TV lines), SuperHAD™ CCD, 0.07 lux at F1.2, CCIR, Genlock, 110-240 VAC

Pelco Manual C2913M-F (08/05) [ 5 ]

CAMERA LAYOUT

Figure 1. Camera Layout

INSTALLATION

Lens Mounting

MC3610 and MC3710 Series cameras can use fixed iris, manual iris, auto iris, or direct drive lenses. Cameras
are factory-set for CS-mount lenses, but are easily adjusted for C-mount lenses.

1. C-Mount Lens Only - Loosen the two back focus locking screws. Rotate the back focus adjust-

ment ring fully counterclockwise before installing the C-mount lens (refer to the section on Back Focus
Adjustment).

2. Screw the lens onto the lens mount. Be careful to prevent dust from entering the space between the

lens and the CCD element. If necessary, use clean, compressed air to remove any foreign matter.

3. Auto Iris Lens Only - Connect the auto iris lens to the four-pin iris drive connector located on

the side of the camera. Pin connections for the iris drive connector are as follows.

Camera Connector

Maximum load:
50 mA video auto iris lens
25 mA direct drive lens

[ 6 ] Pelco Manual C2913M-F (08/05)

PIN DC (AID) AUTO IRIS LENS VIDEO (AIV) AUTO IRIS LENS

1 Control coil positive (+) Not used
2 Control coil negative (-) Lens positive supply
3 Drive coil negative (-) Ground
4 Drive coil positive (+) Video drive signal

Figure 2. AID/AIV Lens Connector

Camera Mounting

Mounting points are provided on the top and bottom of the camera and are used to mount the camera on a
bracket or tripod. They are designed to accept standard photographic mounting bolts (1/4-inch UNC-20). The
mounting bracket must be capable of supporting the weight of the camera and its lens.

NOTE: Some installation codes dictate that the mounting bracket must be capable of supporting up to four
times the combined weight of the camera and lens.

Figure 3. Camera Mounting

CONNECTIONS

MC3610 and MC3710 Series cameras offer standard power and coax video connectors as well as an RJ45-10
connector that combines low voltage power and video (composite or UTP except MC3710S models which do
not have a UTP output). These cameras also have a service connector allowing a video monitor to be connected
locally to the camera using a composite video BNC cable.

Video Connections

To obtain a video output, connect a video coaxial cable terminated with a 75Ω BNC connector to the BNC
socket marked VIDEO OUT on the rear of the camera. Refer to T able A for the type of video coaxial cable to use.

Table A. Video Coaxial Cable Requirements

Cable Type* Maximum Distance

RG59/U 750 ft (229 m)

RG6/U 1,000 ft (305 m)

RG11/U 1,500 ft (457 m)

* Minimum cable requirements:

75 ohms impedance
All-copper center conductor
All-copper braided shield with 95% braid coverage

Another way to transmit video is over unshielded twisted pair wiring through the RJ45-10 connector. Refer to
the RJ45-10 Connections section. When using the Genlock connector or outputting composite video through
the BNC or RJ45-10, do not send UTP output to a passive UTP receiver. However it is acceptable to use an
active UTP receiver for UTP output in combination with the other video connections.

Pelco Manual C2913M-F (08/05) [ 7 ]

Power Connections

MC3610 and MC3710 Series cameras are available in AC high voltage and AC/DC low voltage types. The
voltage required to operate the camera is clearly marked on the rear panel of the camera. The green POWER
LED on the rear panel indicates that power is connected. Power low voltage cameras only from a UL Listed
Class 2 isolated power supply. Power consumption is 4 watts.

Mains Power Supply

Cameras that are intended to operate directly from the mains supply are fitted with a nondetachable power
supply cord. The voltage of operation is 110 to 240 VAC at 50/60Hz.

WARNING: Refer to the wiring instruction label attached to the supply cord. For instances
where the camera will be connected to a socket outlet, the camera should be connected to an
easily accessible socket outlet near to the camera. For instances where the camera will be
connected to the building installation, the building wiring should incorporate a readily accessible
disconnect device, with a contact separation greater than three millimeters. This device should be
fitted into the live conductor, if that is readily identifiable, or should be 2-pole. All installations shall
be carried out in accordance with the locally applicable installation rules.

WARNING: Fuse (F1) should only be replaced by one of equivalent type and rating
1A (T) HRC 250V

WARNING: This camera is a Class 2 device and therefore does not have an earth connection
in the power cord. The leakage current on these cameras is well within safe limits. However, it is
advisable to connect the coaxial or RJ45-10 cable from the camera to the receiving equipment
(such as a monitor or matrix) before applying power to the camera, so that this small leakage
current has a low resistance path to earth.

Low Voltage Power Supply

Cameras fitted with an automatic-switching low voltage power supply operate at 10.8 to 13.8 VDC (12 VDC

-10% +15%) or 20.4 to 27.6 VAC (24 VAC ±15%) at 50/60Hz. Connections and polarity are indicated adjacent
to the screw terminals on the rear panel.

Refer to Table B for the recommended wire gauge and wiring distances.

WARNING: When powering the camera via the screw terminals, ensure that the power
connections to the RJ45-10 connector are not used, and that any connections to the RJ45-10 are
not shorted together. The power supply must be a UL Listed Class 2 isolated type.

CAUTION: AC Operation Only - When wiring more than one camera to the same transformer,
connect the same side of the transformer to the same terminal on all cameras. Failure to connect
all of the cameras the same way will cause the cameras to be out of phase with each other and
may produce a vertical roll when switching between cameras.

[ 8 ] Pelco Manual C2913M-F (08/05)