This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
RADIO AND TELEVISION INTERFERENCE
This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However there is no guarantee that the interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and the receiver.
•
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
You may also find helpful the following booklet, prepared by the FCC: “How to Identify and Resolve Radio-TV Interference Problems.”
This booklet is available from the U.S. Government Printing Office, Washington D.C. 20402.
Changes and Modifications not expressly approved by the manufacturer or registrant of this equipment can void your authority to operate this
equipment under Federal Communications Commission’s rules.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
Cautions
To avoid damaging your camera, please note the following:
1. The camera has threaded mounting locations on the top and bottom of the case. Use only a standard photographic mounting bolt with a
1/4-20 UNC thread.
2. Before fitting the lens, make sure its back will not touch the camera imager or associated components when fully installed.
3. Do not touch the surface of the optical filter. If the filter is accidentally touched, use only isopropyl alcohol to clean it.
4. Do not expose the camera imager to direct sunlight as this may impair camera performance.
6C2910M-C (4/06)
Description
The CCC5100H Series camera is a high resolution, 480 TV line, wide dynamic range video camera with a 1/3-inch SIMD imager. It automatically
senses and sets the video standard to NTSC or PAL. It supports DC-drive auto iris lenses as well as C- and CS-mount lenses. The CCC5100H
Series camera also automatically supports Coaxitron
range of options and settings than other cameras.
The CCC5100H Series camera introduces a new era in video imaging technology. The single instruction, multiple data (SIMD) imager is the first
to be designed and optimized for security applications. This wide dynamic range camera can “see” both light and dark objects in the same scene,
even in scenes where harsh glare, bright light, and shadows make seeing the details a challenge. The SIMD camera uses a multisampling
approach to achieve higher image quality than any CCD camera currently on the market. Each of the more than 388,000 pixels operates like an
individual camera. As lighting conditions change at each pixel, the camera adjusts the exposure time for that pixel. As a result, the
CCC5100H Series camera produces sharp, clearly identifiable images with true color reproduction over a wide range of lighting conditions.
®
as well as the Pelco D and Pelco P protocols. Using its setup menus, it offers a wider
MODEL
MULTIFUNCTION
(RJ45-10) CONNECTOR
VIDEO
CONNECTOR
AUTO IRIS
LENS CONNECTOR
SERVICE
CONNECTOR
Figure 1. CCC5100H Series Camera
CCC5100H-6A 1/3-inch high resolution SIMD digital color camera, 12 VDC/24 VAC
BACK FOCUS
ADJUSTMENT
POWER
CONNECTOR
SETUP
BUTTONS
C2910M-C (4/06)7
PARTS LIST
CCC5100H Series camera
Quick Start Guide
Two-pin terminal block
Four-pin auto iris connector
Lens mount cap
Resource CD:
•
Installation/Operation manual: INSTALL.PDF
•
Quick Start Guide: QSG.PDF
•
Important Safety Instructions: SAFETY.PDF
OPTIONAL ACCESSORIES
PCM150Adjustable camera mount
CST150 Handheld camera setup tool with microdisplay
CST100 Handheld camera setup tool with video output connector
8C2910M-C (4/06)
Lens Mounting
The CCC5100H Series camera supports both manual and DC-drive auto iris lenses, either fixed focal length or varifocal. The camera accepts both
CS- and C-mount lenses without a mount adapter.
NOTE: The CCC5100H Series camera does not support video-drive auto iris lenses.
WIRING AN AUTO IRIS LENS
DC-drive auto iris lenses are controlled through the four-pin drive connector (type D4-152N). Figure 2 identifies the pin connections for the auto
iris lens connector on the back of the camera.
2
4
MOUNTING THE LENS
When mounting the lens onto the camera, refer to Figure 3:
1. Use clean, compressed air to make sure there is no dust or other foreign matter between the lens and the camera imager.
2. Screw the lens onto the lens mount.
3.DC-drive auto iris lens: Connect the four-pin connector from the lens to the connector on the back of the camera.
NOTE: Before using a DC-drive auto iris lens, you must adjust the DC offset setting (refer to DC-Drive Auto Iris Lens Setup).
Figure 2. DC-Drive Auto Iris Lens Connections (Camera Connector)
C/CS LENS
AUTO IRIS
LENS CABLE
AND CONNECTOR
(OPTIONAL)
Figure 3. Mounting Lens to Camera
C2910M-C (4/06)9
Camera Mounting
The CCC5100H Series camera can be mounted from either the top or bottom, depending on the type of camera mount used in your installation.
Use a standard 1/4-20 screw (provided) with a maximum thread length of 0.375 inch (10 mm).
WARNING: The maximum thread depth is 0.4 inch (1 cm). Do not use a longer screw or you may damage the camera.
The optional Pelco PCM150 camera mount is designed specifically for CCC5100H Series cameras. It can be used to wire and mount both high and
low voltage models quickly. (Refer to
the PCM150 camera mount.)
Using the Multifunction Connector
as well as the PCM150 documentation for more information about using
Figure 4.
The CCC5100H Series camera can be fitted with most Pelco lenses and mounted into most Pelco domes and enclosures, resulting in the greatest
possible number of combinations. This means you can find a solution for nearly any application.
When selecting a lens, dome, or enclosure for this camera, consider how the physical dimensions of each component may affect camera
installation
•
•
•
NOTE:
or enclosure. Pelco will build and test it for you. Contact Pelco or your dealer for more information.
and
operation. Specifically, you should address the following three issues.
Enclosure size:
enough for both the camera and the lens.
Lens size:
length. This could affect how it fits within the enclosure.
Optical alignment:
be obstructed by the enclosure itself. The camera sled in many Pelco enclosures has a low side and a high side. You may be able to raise
the optical center by simply flipping the camera sled to the high side.
To simplify lens and enclosure selection, Pelco offers ImagePak
The camera dimensions are 3.60 (L) x 2.77 (W) x 2.4 (H) inches (9.14 x 7.03 x 6.09 cm). Make sure the enclosure is large
Some lenses have minimum and maximum lengths. To focus the scene correctly, you may have to adjust the lens to its maximum
The optical center of this camera may be too low for some enclosures. As a result, the lower portion of the scene may
CCC5100H Series Camera and PCM150 Mount
®
options for the CCC5100H Series camera. Select the lens and the dome
10C2910M-C (4/06)
Power, Video, and Control Connections
The CCC5100H Series is a low voltage camera. Maximum power consumption is about 4.5 watts.
The CCC5100H Series camera offers standard power and coax video connectors as well as a multifunction connector that combines power, video
(coax and unshielded twisted pair), and control leads for quick installation (refer to Using the Multifunction Connector for more information).
Before installation, identify how you will connect each power, video, and control lead to the camera.
CONNECTING POWER
The CCC5100H Series camera operates from either a 12 VDC or a 24 VAC power source. They automatically sense power type and polarity.
Use only a Class 2 isolated power source that can supply 12-36 VDC ±10% or 24-28 VAC ±10%, 47-63 Hz.
NOTE: (AC power only) When connecting more than one camera to the same AC transformer, connect the same side of the transformer to the
same terminal on all cameras. Otherwise, the cameras may be out of phase, causing a vertical roll when switching between cameras. Refer to
Camera Synchronization for more information.
Use Table A to help you identify the necessary wire gauge and maximum cable distance. This table applies to two-conductor copper wire.
These maximum distances are based on a maximum allowable voltage drop of 10%.
Table A. Recommended Wire Gauge and Maximum Wiring Distances
Wire Gauge
24 AWG (0.25 mm
22 AWG (0.35 mm
20 AWG (0.5 mm
18 AWG (1.0 mm
16 AWG (1.5 mm
14 AWG (2.5 mm
12 AWG (4.0 mm
10 AWG (6.0 mm
2
) 62 ft (18 m)251 ft (76 m)
2
)99 ft (30 m)399 ft (121 m)
2
)158 ft (48 m)634 ft (193 m)
2
)251 ft (76 m)1,007 ft (306 m)
2
)399 ft (121 m)1,599 ft (487 m)
2
)634 ft (193 m)2,539 ft (773 m)
2
)1,007 ft (306 m)4,031 ft (1,228 m)
2
)1,600 ft (487 m)6,400 ft (1,950 m)
Maximum Distance
12 VDC24 VAC
Connect power to the terminal block that is supplied with the camera. Then plug the terminal block into the two-pin connector on the back of the
camera. If using the multifunction connector, refer to Using the Multifunction Connector.
WARNINGS:
•
Do not connect high voltage power to the two-pin power connector on the rear panel or you may damage the camera.
•
Apply power to either the power connector or the multifunction connector. The camera cannot accept power at both connectors at the
same time.
C2910M-C (4/06)11
USING COAX VIDEO
The CCC5100H Series camera outputs coax video from either the BNC connector on the rear panel or through the multifunction connector.
The camera also supports two Pelco up-the-coax technologies.
Selected Pelco multiplexers and switchers send a Pelco V-Sync signal to the camera. The camera uses this signal to lock its vertical
synchronization pulse to all other connected cameras. This eliminates certain display problems at the head-end.
Pelco Coaxitron lets you access and configure the camera settings remotely from selected Pelco devices.
Connect a video cable to the BNC connector on the back of the camera. Refer to Table B for the type of video coaxial cable to use. If using the
multifunction connector, refer to Using the Multifunction Connector.
Table B. Video Coaxial Cable Requirements
Cable Type*Maximum Distance
RG59/U750 ft (229 m)
RG6/U1,000 ft (305 m)
RG11/U1,500 ft (457 m)
*Cable requirements:
75 ohms impedance
All-copper center conductor; steel-center conductor cable may result in poor performance
All-copper braided shield with 95% braid coverage
12C2910M-C (4/06)
USING THE MULTIFUNCTION CONNECTOR
The CCC5100H Series camera combines data, video, and power leads into a single multifunction connector on the rear panel. This lets you
quickly install and uninstall the camera.
NOTES:
•
Do not connect a network cable into the multifunction connector on the camera’s rear panel. It is not a network connector.
•
The PCM150 camera mount is designed for the CCC5100H Series camera. It includes a preconfigured cable and an easy-to-wire adapter
plate.
The camera supports two different RJ-45 plugs, depending on the application. Use a 10-pin RJ45-10 plug. (The 10-pin RJ45-10 plug is also
known as an RJ-50 plug.) If you will not use camera control to access the on-screen menus, you can use an 8-pin RJ-45 plug.
To install the multifunction connector
1. Have the following:
•
Unshielded twisted pair cable, either 10-conductor in five twisted pairs or 8-conductor in four twisted pairs. If you will not implement
UTP video, you can use flat Cat5 or Cat6 cable.
•
RJ45-10 (10-pin) or RJ-45 (8-pin) plugs
•
A crimping tool that matches the plug type: RJ45-10 (10-pin, 10-conductor) or RJ-45 (8-pin, 8-conductor)
2. Identify the multifunction connector leads that you will use.
3. Wire the cable and connectors according to Table C. Figure 5 identifies pin 1 on the multifunction connector.
4. Plug the multifunction connector into the camera. Each pair of leads is described in more detail in Control Leads, Coax Video Leads,
Unshielded Twisted Pair (UTP) Leads, and Power Leads.
Table C. Multifunction Connector
By PinBy Pair
Pin Lead Pin Lead
1Pelco Data RX+ 1Pelco Data RX+
2Coax Video Return 10Pelco Data RX3Coax Video 3Coax Video
4Reserved 2Coax Video Return
5UTP- Video 6UTP+ Video
6UTP+ Video 5UTP- Video
7Reserved 912 V / 24 V
8GND / 24 V 8GND / 24 V
912 V / 24 V 4Reserved
10Pelco Data RX-7Reserved
PIN 1
Figure 5. Multifunction Connector, Pin 1
C2910M-C (4/06)13
CONTROL LEADS
The CCC5100H Series camera lets you access and configure the menu settings from any Pelco keyboard, receiver, or other device that supports
the Pelco D or Pelco P protocol. The camera supports the following settings:
•
Baud rate:2400, 4800, 9600
•
Start bit:1
•
Data bits:8
•
Stop bit:1
•
Parity:None
When connecting external control, the wiring should meet the following requirements:
•
24 AWG (0.25 mm
•
Shielded twisted pair
•
Up to 4,000 ft (1,219 m) maximum
2
) or 22 AWG (0.35 mm
Connect the control wires from the Pelco device to the multifunction connector (refer to Table D).
Table D. Device Transmit (TX) to Camera Receive (RX) Connections
2
)
PinLeadPelco Device
1Pelco Data RX+TX+
10Pelco Data RX-TX-
NOTE: To use the control leads, you must use an RJ45-10 plug.
COAX VIDEO LEADS
Connect the coax video wires to the multifunction connector (refer to Table E). Refer to Table B for the maximum video cable distance (BNC).
Table E. Coax Video Connections
PinLead
2Coax Video Return
3Coax Video
14C2910M-C (4/06)
Loading...
+ 30 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.