Pelco C2525, C2525E, C2506E User Manual

C934M-F (7/99) C2506/C2525 Pre-Wired Interconnecting Cables

3500 Pelco Way, Clovis, CA 93612-5699 USA

In North America & Canada: Tel (800) 289-9100 FAX (800) 289-9150

International Customers: Tel (1-559) 292-1981 FAX (1-559) 348-1120

www.pelco.com

IMPORTANT SAFEGUARDS AND WARNINGS

Prior to installation and use of this product, the following WARNINGS should be observed.

1. Installation and servicing should be done by qualified service and installation personnel only.

2. Installation should be done in accordance with all local and national electrical and mechanical codes using only approved materials.

The product and/or manual may bear the following marks:

This symbol indicates that dangerous voltage constituting a risk of electric shock is present within this unit.

This symbol indicates that there are important operating and maintenance instructions in the literature accompanying this unit.

Please thoroughly familiarize yourself with the information in this manual prior to installation and operation.

CAUTION:

RISK OF ELECTRIC SHOCK.

DO NOT OPEN.

DESCRIPTION

The C2506 and C2525 are pre-wired cables used to connect Pelco’s CX9000 Series Coaxitron receiver with Pelco’s SB1900, SB2500, SB2600, and SS2000 Series domes and Legacy® Series pan and tilts in indoor applications only. The C2506E and C2525E are used with CX9000 Series receivers and Legacy® Series pan and tilts in outdoor applications.

Models

C2506 Indoor, 6-foot (1.8 m), pre-wired interconnecting cable (UL) C2506E Same as C2506 but for outdoors C2525 Indoor, 25-foot (7.6 m), pre-wired interconnecting cable (UL) C2525E Same as C2525 but for outdoors

INSTALLATION

1. Connect the male 37-pin CPC connector to the Coaxitron® receiver.

2. Connect the female 37-pin CPC connector to the dome or pan and tilt unit.

3. Use the controller to perform the following functions (if applicable) and verify each operates correctly:

• Pan left • Zoom tele • Preset operation

• Pan right • Iris open • Camera power

•Tilt down • Iris closed • Enclosure power

• Tilt up • Focus near • Camera sync

• Zoom wide • Focus far

Installation is complete when all the above functions operate correctly. If they do not, refer to the

Troubleshooting

section.

TROUBLESHOOTING

1. If any of the functions do not operate correctly, check the cable wiring (refer to Figure 1).

If the pan and tilt functions operate backwards (for example, “tilt up” actually tilts down and “pan right” actually pans left), pins 3 and 7 for pan and pins 5 and 6 for tilt are reversed. You can correct the problem in the field with a CPC pin/socket extracting tool by exchanging the reversed function. If you lack the necessary tool, contact Pelco for a return authorization number to exchange the cable.

2. If the connections are loose, tighten the lock ring on the CPC connectors.

3. Check the Coaxitron® receiver to determine if it is operating correctly.

WIRING DIAGRAM

37 PINS

29 33

34 37

10 15

16 22

23 28

CON206305-1

FIRST 6-CONDUCTOR CABLE

RECEIVER SIDE PAN & TILT SIDE

AC ENCL (HI) 15 RED 15 AC ENCL (HI)

AC ENCL (LOW) 16 BLK 16 AC ENCL (LOW)

AUTO IRIS 2 WHT 2 AUTO IRIS

SPARE 1 17 GRN 17 SPARE 1 SPARE 2 18 BLU 18 SPARE 2 SPARE 3 19 BRN OR ORG 19 SPARE 3

SECOND 12-CONDUCTOR CABLE

RECEIVER SIDE PAN & TILT SIDE

PRESET GND 28 BRN 28 PRESET GND

PRESET HI 29 RED 29 PRESET HI

PAN B PRESET 33 BLU 33 PAN B PRESET

FOCUS PRESET 34 VIO 34 FOCUS PRESET

ZOOM PRESET 35 GRY 35 ZOOM PRESET

TILT PRESET 36 WHT 36 TILT PRESET

PAN A PRESET 37 BLK 37 PAN A PRESET

CAM SYNC CORE 30 ORG 30 CAM SYNC CORE

WIPER 25 PINK (OR RED/WHT) 25 WIPER

WASHER 26 TAN (OR BLK/WHT) 26 WASHER

HB (PAN & TILT) LOW 32 GRN 32 HB (PAN & TILT) LOW

HB (PAN & TILT) HI 31 YEL 31 HB (PAN & TILT) HI

37 SOCKETS

33 29

37 34

15 10

22 16

28 23

CON206306-1

RECEIVER PAN & TILT SIDE

COMMON 1 BRN 1 COMMON

LEFT 3 RED 3 LEFT

DOWN 5 ORG 5 DOWN

UP 6 YEL 6 UP

RIGHT 7 GRN 7 RIGHT

GROUND 8 BLU 8 GROUND

CAMERA HI 9 VIO 9 CAMERA HI

IRIS 10 GRY 10 IRIS

FOCUS 11 WHT 11 FOCUS

ZOOM 12 BLK 12 ZOOM

LENS COM 13 TAN (OR BLK/WHT) 13 LENS COM

CAMERA LOW 14 PINK (OR RED/WHT) 1 4 CAMERA LOW

FIRST 12-CONDUCTOR CABLE

COAX CORE

27 VIDEO CORE

4 VIDEO SHIELD

COAX SHIELD

CABLE PART NUMBER CABLE LENGTH

C2506/C2506E 6 FEET C2525/C2525E 25 FEET

SPECIFICATIONS

MECHANICAL

Connectors

Receiver side: CPC, 37 pins Pan/tilt side: CPC, 37 sockets

ELECTRICAL

Cable

2 lengths: 12 conductors with shield,

20 AWG 1 length: RG59/U 1 length: 6 conductors, 20 AWG

GENERAL

Dimensions

C2506/C2506E: 6 ft (1.8 m) long C2525/C2525E: 25 ft (7.6 m) long

Maximum Wire Temperature: 140°F (60°C)

(Design and product specifications subject to change without notice.)

Figure 1. Wiring Diagram

PRODUCT WARRANTY AND RETURN INFORMATION

WARRANTY

Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment.

Exceptions to this warranty are as noted below:

• Five years on FT/FR8000 Series ﬁber optic products.

• Three years on Genex

• Three years on Camclosure CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2, and MC3651H-2X camera models, which have a ﬁve-year warranty.

•Two years on standard motorized or ﬁxed focal length lenses.

•Two years on Legacy ﬁxed dome products.

•Two years on Spectra continuous motion applications.

•Two years on Esprit

• Eighteen months on DX Series digital video recorders, NVR300 Series network video recorders, and Endura

• One year (except video heads) on video cassette recorders (VCRs). Video heads will be covered for a period of six months.

• Six months on all pan and tilts, scanners or preset lenses used in continuous motion applications (that is, preset scan, tour and auto scan modes).

Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco shipment. All goods requiring warranty repair shall be sent freight prepaid to Pelco, Clovis, California. Repairs made necessary by reason of misuse, alteration, normal wear, or accident are not covered under this warranty.

Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from the speciﬁc use or application made of the Products. Pelco’s liability for any claim, whether based on breach of contract, negligence, infringement of any rights of any party or product liability, relating to the Products shall not exceed the price paid by the Dealer to Pelco for such Products. In no event will Pelco be liable for any special, incidental or consequential damages (including loss of use, loss of proﬁt and claims of third parties) however caused, whether by the negligence of Pelco or otherwise.

The above warranty provides the Dealer with speciﬁc legal rights. The Dealer may also have additional rights, which are subject to variation from state to state.

Series products (multiplexers, server, and keyboard).

and ﬁxed camera models, except the CC3701H-2,

, CM6700/CM6800/CM9700 Series matrix, and DF5/DF8 Series

, Esprit®, ExSite™, and PS20 scanners, including when used in

and WW5700 Series window wiper (excluding wiper blades).

™

Series distributed network-based video products.

If a warranty repair is required, the Dealer must contact Pelco at (800) 289-9100 or (559) 292-1981 to obtain a Repair Authorization number (RA), and provide the following information:

1. Model and serial number

2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number

3. Details of the defect or problem

If there is a dispute regarding the warranty of a product which does not fall under the warranty conditions stated above, please include a written explanation with the product when returned.

Method of return shipment shall be the same or equal to the method by which the item was received by Pelco.

RETURNS

In order to expedite parts returned to the factory for repair or credit, please call the factory at (800) 289-9100 or (559) 292-1981 to obtain an authorization number (CA number if returned for credit, and RA number if returned for repair).

All merchandise returned for credit may be subject to a 20% restocking and refurbishing charge.

Goods returned for repair or credit should be clearly identiﬁed with the assigned CA or RA number and freight should be prepaid. Ship to the appropriate address below.

If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico, send goods to:

Service Department Pelco 3500 Pelco Way Clovis, CA 93612-5699

If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico and are instructed to return goods to the USA, you may do one of the following:

If the goods are to be sent by a COURIER SERVICE, send the goods to:

Pelco 3500 Pelco Way Clovis, CA 93612-5699 USA

If the goods are to be sent by a FREIGHT FORWARDER, send the goods to:

Pelco c/o Expeditors 473 Eccles Avenue South San Francisco, CA 94080 USA Phone: 650-737-1700 Fax: 650-737-0933

REVISION HISTORY

Manual # Date Comments

C934M-F 7/99 Revised Figure 1, added certifications, condensed instructions, and reformatted the manual.