Pelco C2495M-A User Manual

INSTALLATION

ICS-DO111ABK
Integrated Camera
System

MR5000 Series Public Viewing System

C2495M-A (1/06)

Important Safety Instructions

CAUTION:

RISK OF ELECTRIC SHOCK.

DO NOT OPEN.

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not block any ventilation openings. Install in accordance with the manufacturer’s
instructions.

6. Do not install near any heat sources such as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce heat.

7. Only use attachments/accessories specified by the manufacturer.

8. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold
with the apparatus. When a cart is used, use caution when moving the cart/apparatus
combination to avoid injury from tip-over.

9. Refer all servicing to qualified service personnel. Servicing is required when the apparatus
has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been
spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or
moisture, does not operate normally, or has been dropped.

10. Installation should be done only by qualified personnel and conform to all local codes.

11. Unless the unit is specifically marked as a NEMA Type 3, 3R, 3S, 4, 4X, 6, or 6P enclosure, it is
designed for indoor use only and it must not be installed where exposed to rain and moisture.

12. Use only installation methods and materials capable of supporting four times the maximum
specified load.

13. Use stainless steel hardware to fasten the mount to outdoor surfaces.

14. To prevent damage from water leakage when installing a mount outdoors on a roof or wall,
apply sealant around the bolt holes between the mount and mounting surface.

CAUTION:

15.
To reduce the risk of electric shock do not perform any servicing other that contained in the
operating instructions unless you are qualified to do so.

16. Only use replacement parts recommended by Pelco.

The product and/or manual may bear the following marks:

These servicing instructions are for use by qualified service personnel only.

This symbol indicates that dangerous voltage
constituting a risk of electric shock is present
within this unit.

This symbol indicates that there are important
operating and maintenance instructions in the
literature accompanying this unit

2 C2495M-A (1/06)

Regulatory Notices

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.

FCC, Class B (except auto iris models)
RADIO AND TELEVISION INTERFERENCE

This equipment has been tested and found to comply with the limits of a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However there is no guarantee that the
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following
measures:

•

Reorient or relocate the receiving antenna.

•

Increase the separation between the equipment and the receiver.

•

Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.

•

Consult the dealer or an experienced radio/TV technician for help.

You may also find helpful the following booklet, prepared by the FCC: “How to Identify and Resolve
Radio-TV Interference Problems.” This booklet is available from the U.S. Government Printing Office,
Washington D.C. 20402.

Changes and modifications not expressly approved by the manufacturer or registrant of this
equipment can void your authority to operate this equipment under Federal Communications
Commission’s rules.

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

C2495M-A (1/06) 3

Description

Designed specifically for the MR5000 Series public viewing system, the ICS-DO111ABK integrated
camera system packages a camera and lens into a small, discreet, high-security dome.

Pelco’s MR5000 Series public viewing system is specifically designed for retail applications to
provide a clear, visual warning to potential shoplifters that these premises are under surveillance.
When properly installed the station is an effective deterrent against shoplifting.

4 C2495M-A (1/06)

Installation

PREPARE VIDEO AND ELECTRICAL CABLING

1. Temporarily remove the bottom end cap of the MR5000 Series mount if the end cap is
installed.

2. Feed the 42-inch video cable (provided) through the monitor feedthrough hole in the mount
arm and out the bottom end of the mount arm.

3. Pull power wires through the ICS-DO111ABK feedthrough hole located at the bottom of the
mount arm. Remove the 0.750-inch plug if it is installed.

C2495M-A (1/06) 5