®
00974
DF8 Series
Pendant Dome
Maintenance/
Service Manual
C2433SM-A (8/02)
Pelco • 3500 Pelco Way • Clovis, CA 93612-5699 USA • www.pelco.com
In North America and Canada: Tel (800) 289-9100 • FAX (800) 289-9150
International Customers: Tel +1(559) 292-1981 • FAX +1(559) 348-1120
CONTENTS
LIST OF ILLUSTRATIONS
LIST OF TABLES
Section Page
IMPORTANT SAFEGUARDS AND WARNINGS................................................................ 3
DESCRIPTION ................................................................................................................... 4
MODELS ....................................................................................................................4
MAINTENANCE ................................................................................................................. 4
EXPLODED ASSEMBLY DIAGRAMS................................................................................ 5
WARRANTY AND RETURN INFORMATION..................................................................... 8
Figure Page
1 Exploded Assembly Diagram–DF8 Pendant Models ............................................ 5
2 Exploded Assembly Diagram–Heater and Fan Assembly (Outdoor Models Only) .. 6
3 Exploded Assembly Diagram–Pendant Lower Dome ........................................... 7
Table Page
A Exploded Assembly Parts List–DF8 Pendant Models ........................................... 5
B Exploded Assembly Parts List–Heater and Fan Assembly (Outdoor Models Only) . 6
C Exploded Assembly Parts List–Pendant Lower Dome .......................................... 7
2 Pelco Manual C2433SM-A (8/02)
IMPORTANT SAFEGUARDS AND WARNINGS
Prior to installation and use of this product, the following WARNINGS should be observed.
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not block any ventilation openings. Install in accordance with the manufacturer’s
instructions.
6. Do not install near any heat sources, such as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce heat.
7. Only use attachments/accessories specified by the manufacturer.
8. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer or
sold with the apparatus. When a cart is used, use caution when moving the cart/
apparatus combination to avoid injury from tip-over.
9. Refer all servicing to qualified service personnel. Servicing is required when the
apparatus has been damaged in any way, such as power-supply cord or plug is
damaged, liquid has been spilled or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture, the apparatus does not operate
normally, or the apparatus has been dropped.
10. To reduce the risk of shock, do not perform any servicing other than that contained in
the operating instructions unless you are qualified to do so.
11. The installation method and materials should be capable of supporting four times the
weight of the unit and equipment.
12. Only use replacement parts recommended by Pelco.
13. After replacement/repair of this unit’s electrical components, conduct a resistance
measurement between line and exposed parts to verify the exposed parts have not
been connected to line circuitry.
The product and/or manual may bear the following marks:
This symbol indicates that dangerous voltage constituting a risk of electric shock is
present within this unit.
This symbol indicates that there are important operating and maintenance instructions
in the literature accompanying this unit.
Please thoroughly familiarize yourself with the information in this manual prior to installation
and operation.
CAUTION:
RISK OF ELECTRIC SHOCK.
DO NOT OPEN.
Pelco Manual C2433SM-A (8/02) 3
DESCRIPTION
DF8 Series pendant domes are discreet surveillance domes that are designed for indoor or
outdoor use.
MODELS
DF8-PB-0 Indoor, black, fixed mount pendant dome, black opaque lower dome
DF8-PB-1 Same as DF8-PB-0, except clear viewing window (virtually no light loss)
DF8-PB-2 Same as DF8-PB-0, except chrome lower dome (2 f-stops of light loss)
DF8-PB-3 Same as DF8-PB-0, except gold lower dome (2 f-stops of light loss)
DF8-PG-0 Indoor, gray, fixed mount pendant dome, black opaque lower dome
DF8-PG-1
DF8-PG-2 Same as DF8-PG-0, except chrome lower dome (2 f-stops of light loss)
DF8-PG-3 Same as DF8-PG-0, except gold lower dome (2 f-stops of light loss)
DF8-PG-E0 Outdoor, gray, fixed mount pendant dome, heater and blower, black
DF8-PG-E1 Same as DF8-PG-E0, except clear viewing window (virtually no light loss)
MAINTENANCE
Clean the acrylic dome as necessary to maintain a clear picture. Be careful not to scratch
the surfaces of the dome.
Exterior Surface – Clean the dome’s exterior surface with a nonabrasive cleaning cloth
and cleaning agent that is safe for acrylic plastic. Either liquid or spray cleaner/wax suitable
for fine furniture is acceptable.
with smoked viewing window (1/2 f-stop of light loss)
with smoked viewing window (1/2 f-stop of light loss)
Same as DF8-PG-0, except clear viewing window (virtually no light loss)
opaque lower dome with smoked viewing window (1/2 f-stop of light loss)
Interior Surface (Except Chrome or Gold) – Clean the same as the exterior surface.
Interior Surface (Chrome or Gold) – The inside surface of a chrome or gold dome is
easily scratched. Use the following precautions to maintain the dome’s surface.
1. Always handle the dome from the outside of its circular flange.
2. Never touch the coated inside surface. The acid in your fingerprints will eventually
etch the coating if the fingerprints are not carefully removed according to the recommended cleaning procedure in item 5.
3. If dust or other contaminants accumulate on the dome’s interior, remove the debris
with compressed air. Compressed air cans are available from photographic equipment
or electronic supply dealers.
4. If heavy residue accumulates and cannot be removed with air pressure, rinse with
water and immediately dry with air pressure so that water spots will not remain. Avoid
wiping the coated surface with direct hand pressure – it will easily abrade unless
extreme care is taken. Once scratched, the dome cannot be recoated.
5. If internal wiping is necessary, avoid hand rubbing. Instead, make a wick as follows:
Use a very soft paper towel. Roll a section into a tightly wound tube. Tear the tube in
half, and wet the fuzzy end of the wick with a solution of isopropyl alcohol diluted with
water. Hold the dome with its opening facing downward and wipe the interior of the
dome with the wet end of the wick. Use a circular motion, starting from the outside and
spiraling into the center. Use a new wick for each two passes over the dome.
4 Pelco Manual C2433SM-A (8/02)
EXPLODED ASSEMBLY DIAGRAMS
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
13
15
14
14
Figure 1. Exploded Assembly Diagram–DF8 Pendant Models
Table A. Exploded Assembly Parts List–DF8 Pendant Models
Item Qty Description Part Number
13 Screw, 6-32 x 5/16", pan head, Phillips, gray, with plastic washer ZH6-32X.312GRAY
23 Internal tooth lock washer, #6 (outdoor models only) ZH6LWSIS
31 Sun shield (outdoor models only) MF02-3020-007
41 Top mount, black MF03-7060-174
51 Gasket 70610012
63 Internal tooth lock washer, #8 ZH8LWSIS
73 Screw, 8-32 x 3/8", pan head, Phillips ZH8-32X.375SPP
81 Back box, black MF03-3021-005
91 Base plate PDF54000COMP
10 3 Internal tooth lock washer, #8 ZH8LWSIS
11 3 Nut, 8-32 ZH8-32NUTSH
12 1 Tilt table support leg MF03-3020-002
13 2 Fender washer, 1/4" ZH25X1.50X625
14 3 Split lock washer, 1/4" ZH1/4LWSSL
15 2 Nut, 1/4-20 ZH1/420NUTCH
16 1 Tilt table MF03-3021-003
17 1 Flat washer, 3/16" ZH260X562X65C
18 1 Screw, 1/4-20 x 1/2" ZH1/420X.500CH
NS 1 Trim leash assembly attached to side of back box
NS = Not shown
(outdoor models only)
Top mount, gray MF02-7060-174
Back box, gray MF02-3021-005
Leash 7061005
Internal tooth lock washer, #6 ZH6LWSIS
Nut, 6-32 ZH6-32NUTSH
Nylon cable clamp (outdoor models only) ZH8911
Pelco Manual C2433SM-A (8/02) 5
2
3
5674
1
7
6
01145
Figure 2. Exploded Assembly Diagram–Heater and Fan Assembly (Outdoor Models Only)
Table B. Exploded Assembly Parts List–Heater and Fan Assembly (Outdoor Models Only)
Item Qty Description Part Number
11Circuit board, fan rectifier PCB9000277BASSY
21Spacer, 3/16" diameter x .125", #4 SPA9015
32Fan/heater shroud MF01-1041-013
42Heater pad, 24 VAC, 15W HT01-0321-0202
52Fan, 12 VDC, .7W, 7 cfm ZH65-1240-1044
67Nut, 4-40 ZH4-40NUTSH
77Internal tooth lock washer, #4 ZH4LWSIS
NS 1 Power/heater circuit board on side of back box
Includes thermostat PCB9000300ASSY
On at 40°F (4°C)
Off at 60°F (16°C)
Spacer, .250" outside diameter x .125", #6 SPA8500
Internal tooth lock washer, #6 ZH6LWSIS
Nut, 6-32 ZH6-32NUTSH
NS = Not shown
6 Pelco Manual C2433SM-A (8/02)
1
2
3
4
5
6
7
8
9
10
01146
Figure 3. Exploded Assembly Diagram–Pendant Lower Dome
Table C. Exploded Assembly Parts List–Pendant Lower Dome
Item Qty Description Part Number
15Screw, 6-32 x 1/4", pan head, Phillips (indoor models only) ZH6-32X.250SPP
26Internal tooth lock washer, #6 ZH6LWSIS
31DF8 Heater Ring Assembly (outdoor models only) 3023-004A
41Screw, 6-32 x 1/4", pan head, Phillips ZH6-32X.250SPP
51Lower dome retainer MF00-3020-006
61O-ring ZH69-0105-2756
71Tr im ring gasket GS01-0002-0430
82Screw, 6-32 x 5/16", pan head, ZH6-32X.312GRAY
91Tr im ring, black MF03-3020-010
10 1 Acrylic dome, black opaque with smoked viewing window 80810015-00
5 Screw, 6-32 x 3/8", pan head, Phillips (outdoor models only) ZH6-32X.375SPP
24 VAC, 60W
Includes thermostat
On at 70°F (21°C)
Off at 85°F (29°C)
Phillips, gray, with plastic washer
Tr im ring, gray MF02-3020-010
Acrylic dome, black opaque with clear viewing window 80810015-01
Acrylic dome (chrome) 80810011-2
Acrylic dome (gold) 80810011-3
Pelco Manual C2433SM-A (8/02) 7
PRODUCT WARRANTY AND RETURN INFORMATION
WARRANTY
Pelco will repair or replace, without charge, any merchandise proved defective in material or
workmanship for a period of one year after the date of shipment.
Exceptions to this warranty are as noted below:
• Five years on FT/FR8000 Series fiber optic products.
®
• Three years on Genex
• Three years on Camclosure
CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2, and MC3651H-2X camera models,
which have a five-year warranty.
•Two years on standard motorized or fixed focal length lenses.
•Two years on Legacy
fixed dome products.
•Two years on Spectra
continuous motion applications.
•Two years on Esprit
• Eighteen months on DX Series digital video recorders, NVR300 Series network video
recorders, and Endura
• One year (except video heads) on video cassette recorders (VCRs). Video heads will be
covered for a period of six months.
• Six months on all pan and tilts, scanners or preset lenses used in continuous motion
applications (that is, preset scan, tour and auto scan modes).
Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco
shipment. All goods requiring warranty repair shall be sent freight prepaid to Pelco, Clovis,
California. Repairs made necessary by reason of misuse, alteration, normal wear, or accident
are not covered under this warranty.
Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from
the specific use or application made of the Products. Pelco’s liability for any claim, whether
based on breach of contract, negligence, infringement of any rights of any party or product
liability, relating to the Products shall not exceed the price paid by the Dealer to Pelco for
such Products. In no event will Pelco be liable for any special, incidental or consequential
damages (including loss of use, loss of profit and claims of third parties) however caused,
whether by the negligence of Pelco or otherwise.
The above warranty provides the Dealer with specific legal rights. The Dealer may also have
additional rights, which are subject to variation from state to state.
Series products (multiplexers, server, and keyboard).
®
and fixed camera models, except the CC3701H-2,
®
, CM6700/CM6800/CM9700 Series matrix, and DF5/DF8 Series
®
, Esprit®, ExSite™, and PS20 scanners, including when used in
®
and WW5700 Series window wiper (excluding wiper blades).
™
Series distributed network-based video products.
If a warranty repair is required, the Dealer must contact Pelco at (800) 289-9100 or
(559) 292-1981 to obtain a Repair Authorization number (RA), and provide the following
information:
1. Model and serial number
2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number
3. Details of the defect or problem
If there is a dispute regarding the warranty of a product which does not fall under the
warranty conditions stated above, please include a written explanation with the product
when returned.
Method of return shipment shall be the same or equal to the method by which the item was
received by Pelco.
RETURNS
In order to expedite parts returned to the factory for repair or credit, please call the factory at
(800) 289-9100 or (559) 292-1981 to obtain an authorization number (CA number if returned
for credit, and RA number if returned for repair).
All merchandise returned for credit may be subject to a 20% restocking and refurbishing
charge.
Goods returned for repair or credit should be clearly identified with the assigned CA or RA
number and freight should be prepaid. Ship to the appropriate address below.
If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico, send goods to:
Service Department
Pelco
3500 Pelco Way
Clovis, CA 93612-5699
If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico and are
instructed to return goods to the USA, you may do one of the following:
If the goods are to be sent by a COURIER SERVICE, send the goods to:
Pelco
3500 Pelco Way
Clovis, CA 93612-5699 USA
If the goods are to be sent by a FREIGHT FORWARDER, send the goods to:
Pelco c/o Expeditors
473 Eccles Avenue
South San Francisco, CA 94080 USA
Phone: 650-737-1700
Fax: 650-737-0933
REVISION HISTORY
Manual # Date Comments
C2433SM 9/01 Original version.
C2433SM-A 8/02 Added certifications. Revised
Important Safeguards and Warnings.
Pelco, the Pelco logo, Camclosure, Esprit, Genex, Legacy, and Spectra are registered trademarks of Pelco. © Copyright 2002, Pelco.
Endura and ExSite are trademarks of Pelco. All rights reserved.
8 Pelco Manual C2433SM-A (8/02)
Loading...