Pelco C237M User Manual

C237M (3/99) MRWA Wall Mount

300 W. Pontiac Way, Clovis, CA 93612-5699 USA

In North America & Canada: Tel (800) 289-9100 FAX (800) 289-9150

International Customers: Tel (1-559) 292-1981 FAX (1-559) 348-1120

www.pelco.com

LISTED

IMPORTANT SAFEGUARDS AND WARNINGS

Prior to installation and use of this product, the following WARNINGS should be observed.

1. Installation and servicing should only be done by qualified service and installation personnel.

2. Installation shall be done in accordance with all local and national electrical and mechanical codes utilizing only approved materials.

3. Use only installation methods and materials capable of supporting four times the maximum specified load.

4. Use stainless steel hardware to fasten the mount to outdoor surfaces.

The product and/or manual may bear the following marks:

This symbol indicates that dangerous voltage constituting a risk of electric shock is present within this unit.

This symbol indicates that there are important operating and maintenance instructions in the literature accompanying this unit.

Please thoroughly familiarize yourself with the information in this manual prior to installation and operation.

CAUTION:

RISK OF ELECTRIC SHOCK.

DO NOT OPEN.

DESCRIPTION

The MRWA Wall Mount is designed for indoor use with pendant-mount domes and monitor mounts which utilize a suitable length of 1.5-inch NPT threaded pipe for mounting.

NOTE:

When determining the mount location, consideration must be given to the total weight of both the mount and the equipment selected for use with the mount.

The mounting surface must be adequate to support this total weight.

The MWRA mount is compatible with MR3000/MR3050/MR4050 monitor mounts and most Pelco pendant domes.

INSTALLATION

1. Determine the location for mounting your specific equipment on the wall. Remember to allow for adequate clearance on all sides to insure proper operation of selected equipment.

2. Use the mount itself as a template to mark the required mounting holes (a minimum of six fasteners must be used).

3. Using the fasteners of a suitable size, attach the mount to the chosen surface.

4. Attach the chosen equipment to the MRWA mount using a suitable length of threaded

1.5-inch NPT pipe. Tighten set screw as shown in Figure 1. Remember to be certain that the mount is properly fastened to a surface adequate to support the total weight of the mount and equipment.

SPECIFICATIONS

Construction: Steel Finish: Black polyester powder

coat Dimensions: See Figure 1 Mounting Method: Minimum of six 5/16-inch

diameter mounting

fasteners (not supplied).

(Maximum of nine

fasteners can be used.) Weight: Approximately 11 lb (5 kg) Shipping Weight: 13 lb (5.88 kg)

Figure 1. MWRA Dimensions and Exploded Assembly

WARRANTY AND RETURN INFORMATION

WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below:

• Five years on FT/FR8000 Series fiber optic products.

• Three years on Genex® Series products (multiplexers, server, and keyboard).

• Three years on Camclosure® and fixed camera models, except the CC3701H-2, CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2, and MC3651H-2X camera models, which have a five-year warranty.

• Two years on standard motorized or fixed focal length lenses.

• Two years on Legacy®, CM6700/CM6800/CM9700 Series matrix, and DF5/DF8 Series fixed dome products.

• Two years on Spectra®, Esprit®, ExSite™, and PS20 scanners, including when used in continuous motion applications.

• Two years on Esprit® and WW5700 Series window wiper (excluding wiper blades).

• Eighteen months on DX Series digital video recorders, NVR300 Series network video recorders, and Endura™ Series distributed network-based video products.months on DX Series digital video recorders, NVR300 Series network video recorders, Endura™ Series distributed network-based video products, and TW3000 Series twisted pair transmission products.

• One year (except video heads) on video cassette recorders (VCRs). Video heads will be covered for a period of six months.

• Six months on all pan and tilts, scanners or preset lenses used in continuous motion applications (that is, preset scan, tour and auto scan modes).

Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco shipment. All goods requiring warranty repair shall be sent freight prepaid to Pelco, Clovis, California. Repairs made necessary by reason of misuse, alteration, normal wear, or accident are not covered under this warranty.

Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from the specific use or application made of the Products. Pelco’s liability for any claim, whether based on breach of contract, negligence, infringement of any rights of any party or product liability, relating to the Products shall not exceed the price paid by the Dealer to Pelco for such Products. In no event will Pelco be liable for any special, incidental or consequential damages (including loss of use, loss of profit and claims of third parties) however caused, whether by the negligence of Pelco or otherwise.

The above warranty provides the Dealer with specific legal rights. The Dealer may also have additional rights, which are subject to variation from state to state.

If a warranty repair is required, the Dealer must contact Pelco at (800)289-9100 or (559) 292-1981 to obtain a Repair Authorization number (RA), and provide the following information:

1. Model and serial number

2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number

3. Details of the defect or problem If there is a dispute regarding the warranty of a product which does not fall under the

warranty conditions stated above, please include a written explanation with the product when returned.

Method of return shipment shall be the same or equal to the method by which the item was received by Pelco.

RETURNS In order to expedite parts returned to the factory for repair or credit, please call the factory at (800) 289-9100 or (559) 292-1981 to obtain an authorization number (CA number if returned for credit, and RA number if returned for repair). All merchandise returned for credit may be subject to a 20% restocking and refurbishing charge.

Goods returned for repair or credit should be clearly identified with the assigned CA or RA number and freight should be prepaid. Ship to the appropriate address below. If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico, send goods to:

If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico and are instructed to return goods to the USA, you may do one of the following: If the goods are to be sent by a COURIER SERVICE, send the goods to:

If the goods are to be sent by a FREIGHT FORWARDER, send the goods to:

Service Department Pelco 3500 Pelco Way Clovis, CA 93612-5699

Pelco 3500 Pelco Way Clovis, CA 93612-5699 USA

Pelco c/o Expeditors 473 Eccles Avenue South San Francisco, CA 94080 USA Phone: 650-737-1700 Fax: 650-737-0933

REVISION HISTORY

Manual # Date Comments

C237M 3/99 Original version.