INSTALLATION
SWM4-W Pendant
Wall Mount
C2223M (1/06)
Important Safety Instructions
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Only use attachments/accessories specified by the manufacturer.
6. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold
with the apparatus. When a cart is used, use caution when moving the cart/apparatus
combination to avoid injury from tip-over.
7. Installation should be done only by qualified personnel and conform to all local codes.
8. Unless the unit is specifically marked as a NEMA Type 3, 3R, 3S, 4, 4X, 6, or 6P enclosure, it is
designed for indoor use only and it must not be installed where exposed to rain and moisture.
9. Use only installation methods and materials capable of supporting four times the maximum
specified load.
10. Use only replacement parts recommended by Pelco.
Description
The SWM4-W pendant mount is specifically designed for the Spectra® Mini dome system. The mount
offers full feedthrough connections for a clean installation with no exposed wires.
2 C2223M (1/06)
Installation
The following parts are supplied:
1 Adapter plate with locking screw
1 Pendant wall mount
2 8-32 x 0.75-inch screws
To install the SPM4-W pendant mount:
1. Run 24 VAC power, video (coax or UTP), and camera control wiring to the mounting location. If
using coax video, attach a female BNC connector to the coax cable. Refer to Figure 6, Table D,
Table E, and Table F in the installation manual for the Spectra Mini dome for wiring information.
COAX
VIDEO
CAMERA
CONTROL
UTP
VIDEO
POWER
24 VAC
Figure 1.
C2223M (1/06) 3
Wiring
2. Thread the 24 VAC power, video (coax or UTP), and control wiring through the large access hole
in the adapter plate. Then attach the adapter plate to the mounting surface using either the
top/bottom or left/right pair of mounting holes. (The top/bottom pair is shown in Figure 2.)
NOTE:
If mounting to anything other than a junction box, please select appropriate mounting
hardware for the mounting surface
Figure 2.
4 C2223M (1/06)
Mounting the Adapter Plate
3. Thread the wiring through the pendant wall mount, and then attach the mount to the adapter
plate:
a. Locate the mount hooks in the mount. Hang these hooks onto the adapter plate guides.
b. Make sure all wires are enclosed in the mount.
c. Rock the mount into place.
3a
3b
3c
Figure 3.
C2223M (1/06) 5
Attaching the Mount
4. Lock the mount:
a. Locate the slide lock at the base of the mount. Slide it to the right to secure the mount.
b. Turn the locking screw counterclockwise until the slide lock is secured.
4a
4b
Figure 4.
5. Install the Spectra Mini dome in the mount. Follow the instructions in the
Hard Ceiling
In the
same section, attach the dome drive to the mount with the two 8-32 x 0.75-inch screws that are
supplied with the mount.
6 C2223M (1/06)
installation sections of the installation manual for the Spectra Mini dome system.
Hard Ceiling
section, disregard step 2 about cutting holes in the ceiling. In step 5 of the
Locking the Mount
Switch Settings
and
Specifications
MECHANICAL
Mounting Method Attach the mount to wall; attach Spectra Mini dome with the hardware
GENERAL
Construction
Mount ABS plastic
Adapter Plate Aluminum
Finish White
Weight 0.72lb (0.33 kg)
5.20
(13.21)
supplied with the mount.
3.70
(9.40)
Ø
6.10
(15.49)
7.05
(17.91)
NOTE: VALUES IN PARENTHESES ARE CENTIMETERS; ALL OTHERS ARE INCHES.
C2223M (1/06) 7
PRODUCT WARRANTY AND RETURN INFORMATION
WARRANTY
Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship
shipment.
Exceptions to this warranty are as noted below:
• Five years on FT/FR8000 Series fiber optic products.
• Three years on Genex
• Three years on Camclosure® and fixed camera models, except the CC3701H-2, CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2, and
MC3651H-2X camera models, which have a five-year warranty.
•Two years on standard motorized or fixed focal length lenses.
•Two years on Legacy®, CM6700/CM6800/CM9700 Series matrix, and DF5/DF8 Series fixed dome products.
•Two years on Spectra®, Esprit®, ExSite™, and PS20 scanners, including when used in continuous motion applications.
•Two years on Esprit® and WW5700 Series window wiper (excluding wiper blades).
•Two years (except lamp and color wheel) on Digital Light Processing (DLP®) displays. The lamp and color wheel will be covered for a period of
90 days. The air filter is not covered under warranty.
• Eighteen months on DX Series digital video recorders, NVR300 Series network video recorders, Endura™ Series distributed network-based video
products, and TW3000 Series twisted pair transmission products.
• One year (except video heads) on video cassette recorders (VCRs). Video heads will be covered for a period of six months.
• Six months on all pan and tilts, scanners or preset lenses used in continuous motion applications (that is, preset scan, tour and auto scan modes).
Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco shipment. All goods requiring warranty repair shall be sent freight
prepaid to Pelco, Clovis, California. Repairs made necessary by reason of misuse, alteration, normal wear, or accident are not covered under this
warranty.
Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from the specific use or application made of the Products. Pelco’s
liability for any claim, whether based on breach of contract, negligence, infringement of any rights of any party or product liability, relating to the Products
shall not exceed the price paid by the Dealer to Pelco for such Products. In no event will Pelco be liable for any special, incidental or consequential
damages (including loss of use, loss of profit and claims of third parties) however caused, whether by the negligence of Pelco or otherwise.
The above warranty provides the Dealer with specific legal rights. The Dealer may also have additional rights, which are subject to variation from state
to state.
If a warranty repair is required, the Dealer must contact Pelco at (800) 289-9100 or (559) 292-1981 to obtain a Repair Authorization number (RA), and
provide the following information:
1. Model and serial number
2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number
3. Details of the defect or problem
If there is a dispute regarding the warranty of a product which does not fall under the warranty conditions stated above, please include a written
explanation with the product when returned.
Method of return shipment shall be the same or equal to the method by which the item was received by Pelco.
®
Series products (multiplexers, server, and keyboard).
RETURNS
In order to expedite parts returned to the factory for repair or credit, please call the factory at (800) 289-9100 or (559) 292-1981 to obtain an authorization
number (CA number if returned for credit, and RA number if returned for repair).
All merchandise returned for credit may be subject to a 20% restocking and refurbishing charge.
Goods returned for repair or credit should be clearly identified with the assigned CA or RA number and freight should be prepaid. Ship to the appropriate
address below.
If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico, send goods to:
Service Department
Pelco
3500 Pelco Way
Clovis, CA 93612-5699
If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico and are instructed to return goods to the USA, you may do one of the
following
:
If the goods are to be sent by a COURIER SERVICE, send the goods to:
Pelco
3500 Pelco Way
Clovis, CA 93612-5699 USA
If the goods are to be sent by a FREIGHT FORWARDER, send the goods to:
Pelco c/o Expeditors
473 Eccles Avenue
South San Francisco, CA 94080 USA
Phone: 650-737-1700
Fax: 650-737-0933
for a period of one year
after the date of
REVISION HISTORY
Manual # Date Comments
C2223M 1/06 Original version.
Pelco, the Pelco logo, Camclosure, Esprit, Genex, Legacy, and Spectra are registered trademarks of Pelco. ©Copyright 2006, Pelco.
Endura and ExSite are trademarks of Pelco. All rights reserved.
DLP is a registered trademark of Texas Instruments, Inc.
Loading...